Operating Instructions ZC-NAF27 Before installing and using the camera, please read these instructions throughly and retain them for later reference.
Page 2
Warning CAUTION RISK OF ELECTRIC SHOCK To prevent fire or shock hazard, do not expose the unit to rain or moisture. DO NOT OPEN To avoid electrical shock, do not open the cabinet Refer servicing to qualified personnel only. CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
Contents Features....................................3 Cautions for Safe Operation .............................. 4 Operating Controls and Their Functions........................... 5 Connections ..................................6 Control ....................................7 MENU DESCRIPTIONS ............................... 8 CAMERA ID ................................9 FOCUS MODE SET ............................10-11 AWB SET ................................. 12-13 AE SET ................................14-16 SPECIAL SET ..............................
Cautions for Safe Operation Power Supply • Close to generators of powerful electromagnetic radiation such as radio or TV This camera must always be operated a 12V DC transmitters. power supply. (More than 500mA) Care of the unit Handling of the unit •...
Operating Controls and Their Functions 1. Tripod adaptor This adaptor can also be attached on the bottom of the camera. 2. Lens mount cap 3. TELE Key When push the TELE KEY, picture is telephoto 4. WIDE Key When push the WIDE KEY, picture is wide angle 5.
Connections Power Connection 1. Remove the insulation on the power cable as illustrated. 2. Attach the terminal tips. 3. Connect to the DC 12V terminals on the camera. Connection the monitor 1. To VIDEO OUT 2. To Video input on the monitor...
Control Remote Control Lines are connected to RJ-45 socket as shown below In case of RS-422 INTERFACE (Basic) CONTROL CONTROL OUT Controller In case of Zoom/Focus control Interface (option) ZOOM ZOOM (+Tele, -Wide) COMMON FOCUS FOCUS (+Near, -Far) PIN 8 PIN 1 Receiver/Controller Voltage Range Vcom + (+5~15V)
CAMERA ID 1. CAMERA ID To connect a large number of camera , It can be assigned to identification number to each camera for camera control easily. (OFF, 0 - 255 : total numbers of ID are 256) • It only can be set this function using ID commend. To transfer ID Code of camera , In first byte at PC control.
2. Focus Set: 2-1. Focus Mode Set: This function is for focus mode setting A) Set up “FOCUS SET” in main menu using Menu key. Select the “FOCUS MODE” in submenu using PUSH Tele/Wide key. And then set the mode (Auto, Push auto, or Manual) using Focus key.
FOCUS MODE SET 2-4. ZOOM END Set: This function is for selection of zoom end position. Select the “ZOOM END” in submenu using Tele/wide key. Set the Zoom end mode from (Zoom Start + 1) x 270 to X using PUSH Focus key.
AWB SET 3. AWB SET 3-1. WB Mode Set: This function is for changing the WB mode. A) Set up “AWB SET” in main menu using Tele/wide key. B) Select the “WB MODE” in submenu using Tele/wide key. C) Set the mode Auto, Push auto , Manual, Outdoor, Indoor, Special using Focus key.
Page 13
AWB SET 3-3. BLUE ADJUST Set : This function is available for Special ,Push Auto, Manual WB mode. This mode is the adjustment of user option for special color. A) Select the “BLUE ADJUST” in submenu using Tele/wide key. B) Adjust the level from (-30 to 30 SPECIAL, -128 to +127 PUSH AUTO, 0-255 MANUAL) using Focus key.
AE SET 4. AE SET 4-1. AE Mode Set: This function is for changing to AE mode. A) Set up “AE SET” in main menu using Tele/wide key. B) Select the “AE MODE” in submenu using Tele/wide key. C) Set the mode auto, IRIS MAN, AGC MAN, Manual, Auto using Focus key.
Page 15
AE SET 4-4. BRIGHTNESS ADJUSTMENT Set: A) Select the “BRIGHTNESS” in submenu using Tele/wide key. B) Adjust the level from ##MIN to ##MAX. using Focus key. * ## : Current level at Auto mode. 4-5. BACKLIGHT Set: A) Select the “BACKLIGHT” in submenu using Tele/wide key. B) Set the mode OFF, ON, or AUTO using Focus key.
Page 16
AE SET 4-7. SHUTTER SPEED Set: A) Select the “SHUTTER” in submenu using Tele/wide key. B) Set the mode NORMAL, 1/125 - 1/10000 using Focus key. 4-8. INITIAL SET: A) Select the “INITIAL SET” in submenu using Tele/wide Command, B) Set the initial set mode to ON or OFF using Focus key. 4-9.
SPECIAL SET 5. SPECIAL SET 5-1. User Title Set: This function is for custom title on screen display. A) Set “SPECIAL SET” in main menu using Tele/wide key. B) Select the “USER TITLE” in submenu using Tele/wide key. C) Set the position of title and set data using Tele / Wide, Focus key.
Page 18
SPECIAL SET 5-5. NEGATIVE Set: This mode is to change color and luminance to negative. A) Select the “COLOR” in submenu using Tele/wide key. B) Select the mode ON, OFF using Focus key. 5-6. WIDE BURST Set: This mode is to change color burst width for long distance application. A) Select the “WIDEBURST”...
MOTION DET 6. MOTION DETECTION SET 6-1. DETECTION Mode Set: A) Set “MOTION” in main menu using Tele/wide key. B) Select the “DETECTION” in submenu. Using Tele/wide key. C) Set the mode ON, OFF using Focus key. 6-2. LEVEL ADJUST Set: This function is available for DETECTION ON mode.
F . OSD SET 7-1. FUNCTION Set: A) Set “F. OSD” in main menu using Tele/wide key. B) Select the mode what you want in submenu using Tele/wide key. C) Set the display mode of OSD using Tele / Wide, Near/Far key. *INITIAL SET and RETURN are the same as before procedure.
E. SENSITIVITY SET 8. E. SENSITIVITY SET 8-1. E. SENSITIVITY SET A) Select the “E.SENSITIVITY” in submenu using Tele/wide key. B) Select the sensitivity mode what you want in submenu using Focus key. *Mode sequence: OFF-X2 AUTO-X4 AUTO-X8 AUTO-X10 AUTO-X16 AUTO- X32 AUTO -OFF- X2 FIX-X4 FIX -X8 FIX -X10 FIX -X16 FIX - X32 FIX-OFF 8-2.
WDR SET 9. WDR SET 9-1. WDR SET A) Select the “WDR” in main menu using Tele/wide key. B) Select the “WDR CONTROL” in submenu using Tele/wide key. C) Select the WDR mode what you want in submenu using Focus key.
On Screen Display FUNCTION Description Format Some of these functions will 1. Focus Mode Non display Auto Mode be displayed every time the camera is operated and then Manual / push Auto Mode disappeared after 5 seconds. 2. Back Light Non display Back Light OFF “BL”display...
Page 24
On Screen Display FUNCTION OSD Format Description White Balance AUTO 6. WBC Mode Special Auto White Balance; Adjustment Mode according to change of external illuminant. RED ADJUST and BLUE ADJUST (0~255) are available. After changing R/B value, The mainternance mode is “AUTO”. WB Preset for INDOOR (3200°K) Wb Preset for OUTDOOR (5100°K) Manual WB Adjustment;...
Specifications Image device 1/4" interline transfer CCD Image device NTSC, High resolution : 811(H) X 508(V) 410K NTSC, Normal resolution : 537(H) X 505(V) 270K PAL, High resolution : 795 (H) X 596 (V) 470K PAL, Normal resolution : 537(H) X 597(V) 320K Internal Sync system Approx.480 Line (NTSC, High resolution)
Page 26
Specifications English OSD(On Screen Display) DC 9V-15V Power requirement Composite Output 75S Terminated Video output 5.3W Power consumption 0°C - 45°C operating temperature 0% RH - 60% RH Operating Humidity -20°C - 60°C, 0% RH - 85% RH Storage temperature 57mm(W) X 68.9mm(H) X 111.5mm(D) Dimensions 500g...
R S - 4 2 2 / R S - 4 8 5 Command 1. Communication Format 1. Connection Conditions> Data Length 1 Byte ( 8 Bit ) Start/Stop Bit 1 BIT Parity Bit None Baud rate 9,600 bps 2. The communication data format from PC to Camera The data of total 6 bytes is transmitted PC to camera.
Page 28
3. The communication data format from Camera to PC The data of total 6 bytes is transmitted camera to pc. 1) Format BYTE 1 BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6 BYTE 7 BYTE 8 BYTE 9 0xC5 CODE1 CODE2...
Page 29
2. PC Command 1. Read Camera ID This command is to read the ID number on camera that is currently connected. Caution This command is valid only one camera is connected. Control Command [C5h] [CCh] [00h] [00h] [XXh] [Check Sum] Return Data [C5h] [CCh] [00h] [00h] [Camera ID] [Check Mode] [XXh] [XXh] [Check Sum] Parameter Description...
Page 30
2. Change Camera ID 2. Change Camera ID This command is to change the camera ID number which is connected as New ID number or Enable or Disable a "Camera ID Number Check Mode". Control Command [C5h] [78h] [New Camera ID] [Check Mode] [Camera ID] [Check Sum] Return Data [C5h] [78h] [New Camera ID] [Check Mode] [New Camera ID] [XXh] [XXh] [XXh] [Check Sum] Parameter Description...
Page 31
3. Camera ID Display ON/OFF control Change the Camera ID display mode of camera according to the data “Mode”. 1) PC -> Camera 0xC5 0xAA 0x96 Mode CAM_ID C·S 2) Camera -> PC 0xC5 0xAA 0x96 Mode 0x96 0xXX 0xXX 0xXX C·S mode :: This is a data for setting the Camera ID Display Mode.
Page 32
5. Camera Power Off; Turn off power of Camera. Change the Camera ID display mode of camera according to the data “Mode”. 1) PC -> Camera 0xC5 0x3E 0x00 0x00 CAM_ID C·S 2) Camera -> PC 0xC5 0x3E 0x00 0x00 0x00 0xXX 0xXX...
Page 33
7. MENU OSD Display ON/OFF Setting Set the MENU OSD Display mode of the camera to ON or OFF according to the data of “MODE”. 1) PC -> Camera 0xC5 0xAA 0x63 MODE CAM_ID C·S 2) Camera -> PC 0xC5 0xAA 0x63 MODE...
Page 34
9. BACKLIGHT ON/OFF control Switch the BACKLIGHT mode to ON/OFF according to the data of “MODE”. 1) PC -> Camera 0xC5 0xAA 0x70 MODE CAM_ID 2) Camera -> PC 0xC5 0xAA 0x70 MODE 0x70 0xXX 0xXX 0xXX MODE: In case of MODE = 0x01, MENU OSD Display mode is changed to ON mode. In case of MODE = 0x00, MENU OSD Display mode is changed to OFF mode Otherwise, MENU OSD Display mode is not changed.
Page 35
11. 100% NEGATIVE ON/OFF control Switch the 100% NEGATIVE mode to ON/OFF according to data of “MODE”. 1) PC -> Camera 0xC5 0xAA 0x72 MODE CAM_ID 2) Camera -> PC 0xC5 0xAA 0x72 MODE 0x72 0xXX 0xXX 0xXX MODE: In case of MODE = 0x01, The 100% NEGATIVE mode becomes ON mode. In case of MODE = 0x00, The 100% NEGATIVE mode becomes OFFmode.
Page 36
Focus Mode Description • Set "Focus Action Mode" to "Focus Auto/Manual AUTO Mode". • Camera Fulfill "Auto Focus Action". • If "Focus Auto/Manual Or Push Auto" key is inputted, "Focus Action Mode" is changed to "Focus Auto/Manual MANUAL Mode". • Set "Focus Action Mode" to "Focus Auto Manual MANUAL Mode". •...
Page 37
13. FLICKERLESS Mode ON/OFF Setting Switch the FLICKERLESS mode to ON/OFF according to the data of “MODE” 1) PC -> Camera 0xC5 0xAA 0x74 MODE CAM_ID 2) Camera -> PC 0xC5 0xAA 0x74 MODE 0xXXX 0xXX 0xXX 0xXX MODE: In case of MODE = 0x01, The FLICKERLESS mode becomes “ON” mode. In case of MODE = 0x00, The FLICKERLESS mode becomes “OFF”mode.
Page 38
15. SPECIAL White Balance Mode RED adjust data Setting Set the RED adjust data at SPECIAL White Balance mode according to the data of “RED_ADJ”. 1) PC -> Camera 0xC5 0xAA 0x75 RED_ADJ CAM_ID 2) Camera -> PC 0xC5 0xAA 0x75 RED_ADJ 0x75...
Page 39
17. Set Manual Red Gain This commands is to set the value of Red Gain in "MANUAL White Balance Control Mode" or "PUSH AUTO White Balance Control Mode". Caution It is valid when White Balance Control Mode is "MANUAL White Balance Control Mode" or "PUSH AUTO White Balance Control Mode".
Page 40
19. White Balance PUSH_AUTO ON/OFF Setting Switch the PUSH AUTO White Balance state to ON or OFF White Balance mode according to the data of “MODE”. 1) PC -> Camera 0xC5 0xAA 0x78 MODE CAM_ID 2) Camera -> PC 0xC5 0xAA 0x78 MODE...
Page 41
21. BRIGHTNESS Data Setting Set the brightness level of the camera according to the data of “Brightness”. 1) PC -> Camera 0xC5 0xAA 0x00 CAM_ID 2) Camera -> PC 0xC5 0x62 0x00 0xXX 0xXX 0xXX Brightness ; This is a data for which adjusts a brightness level of the camera. 22.
Page 42
23. ZOOM END Data Setting Set the zoom end magnification of the camera according to the data of “End 1) PC -> Camera 0xC5 0x62 0x7A Brightness CAM_ID 2) Camera -> PC 0xC5 0xAA 0x7A Brightness 0x7A 0xXX 0xXX 0xXX End : This is a data for which adjusts a zoom end magnification of the camera.
Page 43
25. Exposure Mode Set Command Set the mode of Exposure according to AEmodeCNT 1) PC -> Camera 0xC5 0xAA 0x60 AEmodeCNT CAM_ID 2) Camera -> PC 0xC5 0xAA 0x60 0x60 0xXX 0xXX 0xXX AEmodeCNT AEmodeCNT : The counter for setting Exposure mode 1.
Page 44
26. SHUTTER Speed Setting Set the shutter speed of the camera according to the data of “SSS_CNT”. 1) PC -> Camera 0xC5 0xAA 0x78 SSC_CNT CAM_ID 2) Camera -> PC 0xC5 0xAA 0x78 SSC_CNT 0x78 0xXX 0xXX 0xXX SSC_CNT NTSC SSC_CNT NTSC 1/60...
Page 45
27. IRIS OPEN Level Setting Set the IRIS OPEN Level of the camera according to the data of “IRIS_CTL”. 1) PC -> Camera 1) PC -> Camera 0xC5 0xAA 0x7C IRIS_CTL CAM_ID 2) Camera -> PC 0xC5 0xAA 0x7C IRIS_CTL 0x7C 0xXX 0xXX...
Page 46
29. Set Function OSD Display On/Off Mode Register This command is to set the value of Camera's Function OSD Display On/Off Register directly and mode of each Display On/Off for Function OSD. Display On/Off Mode Display On Mode -> Function OSD displays on screen in the key event. Display Off Mode ->...
Page 47
Bit of FOSD_DISP Description • Means value of OR operation among Function OSD fields from Bit 0 to Bit 5. 1 -> have at least one of "Display On Mode" among Function OSD fields from Bit 7 Bit 0 to Bit 5. 0 ->...
Page 48
30. Key Action : Perform the Key action according to the data of “KEY CODE”. aution: After using the Key action, Camera has to be notified by stop of key action code “KN_STOP”. 1) PC -> Camera 0xC5 0x5F KEY_CODE 0x00 CAM_ID 2) Camera ->...
Page 49
3. Key Code Table for "Camera Key Action Control Command" 1. Key Code Table related to Focus Mode Key Name Key Code Description Focus Mode • Change Focus Action Mode. Selection (-> Focus Auto/Manual AUTO Mode -> Focus Auto/Manual MANUAL Mode -> Focus PUSH AUTO Mode -> Focus Auto/Manual AUTO Mode") Focus Auto/Manual or Push Auto (Menu...
Page 50
Key Name Key Code Description • In case of "Focus PUSH AUTO Mode" -> Auto Focus operates while the key is pushed. Focus • Toggle Focus Action Mode to "Focus Auto/Manual AUTO Auto/Manual Mode" or "Focus Auto/Manual MANUAL Mode". Caution It is valid when Focus Action Mode is "Focus Auto/Manual AUTO Mode"...
Page 51
2. Key Code Table related to Manual Focus Action Caution: It is key about Manual Focusing Action. It is valid when Focus Action Mode is "Focus Auto/Manual MANUAL Mode" or "Focus PUSH AUTO Mode". Key Name Key Code Description Quick Speed FAR •...
Page 52
Key Name Key Code Description • Move Focus Lens forward NEAR by 1step. 1step NEAR (Menu • In Menu OSD Displayed, Fulfill Menu Data Up Change Key Action. Data Up Change) • Fulfill only Quick Speed Manual Focus FAR Move Action. Quick Speed FAR Only Quick Speed NEAR...
Page 53
Key Name Key Code Description • Fulfill Manual Focus FAR Move Action at 360pps Speed. 360pps Speed FAR • Fulfill Manual Focus FAR Move Action at 420pps Speed. 420pps Speed FAR • Fulfill Manual Focus NEAR Move Action at 60pps Speed. 60pps Speed NEAR •...
Page 54
3. Key Code Table related to Zoom In/Out Action Key Name Key Code Description Slow Speed Zoom • Fulfill Slow Speed (9sec) Zoom In Action. In (Menu Item Up (or 34h) • In Menu OSD Displayed, Fulfill Menu Item Up Selection Key Action. Selection) Slow Speed Zoom •...
Page 55
Key Name Key Code Description Selected Speed • Fulfill Zoom In Action as "Zoom Tracking Speed" set in Camera. Zoom In (Menu • In Menu OSD Displayed, Fulfill Menu Item Up Selection Key Action. Item Up Selection) Selected Speed • Fulfill Zoom Out Action as "Zoom Tracking Speed" set in Camera. Zoom Out (Menu •...
Page 56
Key Name Key Code Description Selected Speed • Fulfill only Zoom Out Action as Speed set in Menu. Zoom Out Only Optical 8x Auto • Fulfill automatically Zoom In/Out Action in Slow Speed with rotation of the Zoom In/Out order "-> 8x -> 1x". 4.
Page 57
Key Name Key Code Description Instant Digital • Set Instant Digital Zoom to off. Zoom Off • Set Instant Digital Zoom Mode to "x2 Mode". Instant Digital Zoom x2 Setting • Fulfill Zoom In/Out Action in Optical Zoom Region only in state that 2x Digital Zoom is ON and displays "IDX2 ~ IDX54"...
Page 58
5. Key Code Table related to Digital Pan/Tilt Action It is valid when Instant Digital Zoom Mode is x2, x4, x8 Mode or Zoom magnification is in Digital Zoom Region while Digital Zoom operates. Key Name Key Code Description Right Direction •...
Page 59
6. Key Code Table related to Digital Effect Action Key Name Key Code Description Digital Effect • Fulfill Digital Effect in order. Scroll Change • The order of Digital Effect WIDE VISION -> ART -> MIRROR -> 100% NEGATIVE -> 80% NEGATIVE -> Color OFF -> MOSAIC ...
Page 60
7. Key Code Table related to Function & Menu OSD Key Name Key Code Description OSD On/Off • Function OSD Display is Toggled whenever this key is pushed. • If this key is pushed in Menu OSD Displayed, Menu OSD Display is off. 2sec Menu OSD •...
Page 61
Key Name Key Code Description Menu Item Up • In case of displaying Menu OSD, Menu Item Up Selection is Selection Fulfilled. Menu Item • In case of displaying Menu OSD, Menu Item Down Selection Down Selection (or 50h) is Fulfilled. Menu Data Up •...
Page 62
Key Name Key Code Description • Brightness level is Scrolled toward increment. Brightness Up (or 3Ch, • It is invalid in case that Exposure Mode is "MANUAL Exposure Mode". Scroll Change 46h) Brightness • Brightness Level is Scrolled toward decrement. Down Scroll (or 3Dh, •...
Page 63
Key Name Key Code Description • If this key is pushed over 2 seconds, Auto Backlight Control becomes on. • Toggle Flickerless Control Mode On/Off, whenever this key is pushed. Flickerless On/Of • In case Flickerless On, High Shutter Speed is ->...
Page 64
Key Name Key Code Description -> Increase compensation value for Red Gain. • In case of "MANUAL White Balance Control Mode" -> Increase directly value for Red Gain. • In case of "PUSH AUTO White Balance Control Mode" -> Increase Red Position value of Target White Point in Vector. •...
Page 65
Key Name Key Code Description Blue Color • BLUE component of Control Data is decreased. Down Change • It operates like as followings according to White Balance Control Mode. • In case of "SPECIAL White Balance Control Mode" -> Decrease compensation value of Blue Gain. •...
Page 66
S t o p C o mma n d 0 C h S t o p a l l a c t i o n s t h a t a r e b e i n g p e r f o r me d c u r r e n t l y...