Table of Contents
Advertisement
Parts and their functions (continued)
Rear panel
DIGITAL
SDI
IN
VIDEO1
SDI
OUT
VIDEO OUT
DVCPRO
/DV
IEEE1394 digital input/output connector
(option: AJ-YAD255G)
This enables signals to be input and output using the
IEEE1394 digital interface. Use a 6-pin type of connector.
Bus power is not supported.
VIDEO MON connector
Analog composite video signals are output from this connector.
Video signals with information superimposed on them
can be output. To set the superimposing to ON or OFF,
use the SUPER switch
AUDIO MON (L, R) connectors
The playback signal from the PCM audio signals (CH1
and CH2) are output from these connectors.
Fan
This fan is used to cool down the VTR.
If, for any reason, the fan stops, "E-10" will appear on the
counter display.
AC IN socket
Connect one end of the power cord supplied to this
socket and the other end to the power outlet.
SIGNAL GND terminal
This is connected to the signal ground terminal on the
component connected to this VTR in order to minimize
noise. It is not a safety ground.
SERIAL DIGITAL COMPONENT AUDIO
VIDEO IN/OUT connectors
(option: AJ-YA94G)
Digital component audio/video signals complying with the
SMPTE 259M-C standard are input to and output from
these connectors.
Note:
The digital audio signals to be input must be
synchronized with the video input signals. Otherwise,
noise will be generated in the audio output signals.
ANALOG VIDEO IN connectors
The signals which are to be supplied to these connectors
are selected as follows by setting the INPUT SELECT
button on the front panel.
Y P
P
: Analog component video signals are input.
B
R
CMPST: Analog composite video signals are input using
the VIDEO/Y connector
S-VIDEO: S-Video (Y/C separated) signals are input using the
VIDEO/Y connector
Note:
The wide ID superimposed on the input signals is not detected.
ANALOG VIDEO OUT connectors
The signals which are to be output from these connectors
are selected as follows by setting the ANALOG VIDEO
OUT selector switch
Y P
P
(bottom position):
B
R
Analog component video signals are output.
12
VIDEO
IN
VIDEO
IN
P R
Y
P B
750
AUTO
VIDEO2
OUT
Y
C
P B
P R
Y
REF VIDEO IN
TIME CODE
REMOTE
1
2
CH
CH
VIDEO MON
(SUPER)
AUDIO IN
L
1
2
CH
CH
R
AUDIO MON
AUDIO OUT
on the front panel.
.
and PB/C connector
.
1
AC IN
5
SIGNAL
GND
VIDEO1/VIDEO2 (top position):
Two sets of analog composite video signals are output from
connectors
Y/C (middle position):
S-Video (Y/C separated) signals are output from
connectors
Note:
The wide ID is not superimposed onto the output signals.
ANALOG VIDEO OUT selector switch
Set this switch to the Y P
the ANALOG VIDEO OUT connectors for component video
output, set to the VIDEO1 VIDEO2 position (top) when
using for composite video output, and set to the middle
position when using for S-Video (Y/C separated) output.
REF VIDEO IN connector
This is the input connector for the reference video
signal. Input a signal with color burst.
Note:
Since the video or audio output signal may be disrupted
if the reference video signal is not input, it is
recommended that this connector be used by the system
which supplies the reference video signals.
Use a signal where SCH does not fluctuate for the
reference video signal.
REF VIDEO OUT connector
This is the loop-through output connector of the REF
VIDEO IN connector
to this connector, the REF VIDEO IN connector
automatically terminated by the 75 Ω resistance. When a
cable is connected, the 75 Ω termination is released.
TIME CODE IN connector
This connector is used for recording the external time
code onto the tape.
TIME CODE OUT connector
The playback time code is output from this connector during
playback. During recording, the time code generated by the
internal time code generator is output.
Remote control connector
This enables the unit to be connected to the external remote
controller for operation from an external source.
Notes:
• Set the CONTROL switch
.
• The specifications are based on the RS-422A interface,
and editing-related functions do not work. In this case,
use it as a player.
ANALOG AUDIO IN connectors
The analog audio signals are input from these
connectors.
ANALOG AUDIO OUT connectors
The analog audio signals are output from these
connectors.
Signal
Pin No.
1
Frame Ground
6
2
Transmit A
3
Receive B
4
Receive Common
9
5
6
Transmit Common
7
Transmit B
8
Receive A
9
Frame Ground
and
.
and
.
P
position (bottom) when using
B
R
. When a cable is not connected
to REMOTE.
is
Hide quick links:
Advertisement
Table of Contents
