Residual Risks; Package Contents; Electrical Safety; Mains Plug Replacement - DeWalt dw713 User Manual

material to be machined (chip board produces more dust than
wood) and the importance of local extraction (capture or source)
and ensure to make proper adjustment of hoods/baffles/chutes.
• Operator shall be instructed on factors influencing exposure to
noise (e.g. use of saw blade designed to reduce the emitted noise,
saw blade and machine maintenance);
-– Report faults in the machine, including guards or saw blade, as
soon as they are discovered.
-– Provide adequate general or localized lighting.
-– Ensure the operator is adequately trained in the use, adjustment
and operation of the machine.

Residual risks

The following risks are inherent to the use of saws:
– injuries caused by touching the rotating parts
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be
avoided. These are:
– Impairment of hearing.
– Risk of accidents caused by the uncovered parts of the rotating
saw blade.
– Risk of injury when changing the blade.
– Risk of squeezing fingers when opening the guards.
– Health hazards caused by breathing dust developed when sawing
wood, especially oak, beech and MDF.

Package contents

The package contains:
1 Mitre Saw
1 Blade wrench stored in wrench pocket
1 Saw blade
1 Dust bag
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual prior
to operation.
Description (fi g. 1, 2)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
INTENDED USE
Your DW713 mitre saw has been designed for professional cutting of
wood, wood products and plastics. It will perform the sawing operations of
cross-cutting, bevelling and mitring easily, accurately and safely.
The DW713 mitre saw is a professional power tool. DO NOT let children
come into contact with the tool. Supervision is required for those under
16 years of age.
a. Operating handle
b. Lower guard
c. Right side, fence
d. Table
e. Mitre lock lever
f. Mitre scale
g. Base
h. Holes for extension kit
i. Wrench
j. Bench mounting holes
k. Fence clamping knob
l. On/Off switch
m. Carrying handle
n. Dust spout
o. Lock down pin
p. Bevel clamp knob
q. Bevel scale
r. Hand indentation
s. Kerf plate
t. Mitre detent
u. Mitre detent override
v. left side, fence
w. Motor housing
x. Spindle lock
y. Hole for padlock
z. Angle postion stop
aa. Bevel position adjustment stop
bb. Vertical position adjustment stop
cc. Head lock up lever
dd. Rear lower guard
ee. Upper guard
Optional Accessories (fi g. 3)
ff. Dust bag
gg. Clamp
hh. Lazer
ii. Length stop
jj. Work support

Electrical safety

The electric motor has been designed for one voltage only. Always
check that the power supply corresponds to the voltage on the rating
plate.
Your tool is double insulated in accordance with EN 61029;
therefore no earth wire is required.
In case of cord replacement the tool must only be repaired by an
authorized service agent or by qualified electrician.

Mains plug replacement

(U.K. & Ireland only)
DANGER:
• Should your mains plug need replacing and you are competent to
do this, proceed as instructed below. If you are in doubt, contact
an authorized D WALT repair agent or a qualified electrician.
E
• Disconnect the plug from the supply.
• Cut off the plug and dispose of it safely; a plug with bared copper
conductors is dangerous if engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs fitted with the
correctly rated fuse (1).
• The cable wire colours, or a letter, will be marked at the connection
points of most good quality plugs. Attach the wires to their
respective points in the plug (see below). Brown is for Live (L) (2)
and Blue is for Neutral (N) (4).
• Before replacing the top cover of the mains plug ensure that the
cable restraint (3) is holding the outer sheath of the cable firmly and
that the two leads are correctly fixed at the terminals crews.
4
3
ENGLISH
1
2
11