Table of Contents
Advertisement
Quick Links
Image not readable or empty
images/manufacturers/Philio.png
PHI_PSM01
Z-Wave 3 in 1
Sensor(Door-
/Window,
Temperature,
Illumination)
Firmware Version : 1.0
Quick Start
S
This device is a Z-Wave Sensor. Tripple Click the Temper Switch on the backside to confirm inclusion,
exclusion and association.
Please refer to the chapters below for detailed information about all aspects of the products usage.
What is Z-Wave?
This device is equipped with wireless communication complying to the Z-Wave standard. Z-Wave is the
international standard for wireless communication in smart homes and buildings. It is using the
frequency of 868.42 MHz to realize a very stable and secure communication. Each message is reconfirmed
(two-way communication) and every mains powered node can act as a repeater for other nodes (meshed
network) in case the receiver is not in direct wireless range of the transmitter.
Z-Wave differentiates between Controllers and Slaves. Slaves are either sensors (S) transmitting metered or
measured data or actuators (A) capable to execute an action. Controllers are either static mains powered
controllers (C) also referred to as gateways or mobile battery operated remote controls (R). This results in a
number of possible communication patterns within a Z-Wave network that are partly or completely supported
by a specific device.
1. Controllers control actuators
2. Actuators report change of status back to controller
(c) 2012 Z-Wave Europe GmbH, Goldbachstr. 13, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Philio Technology Corporation PSM01
Summary of Contents for Philio Technology Corporation PSM01
- Page 1 Image not readable or empty images/manufacturers/Philio.png PHI_PSM01 Z-Wave 3 in 1 Sensor(Door- /Window, Temperature, Illumination) Firmware Version : 1.0 Quick Start This device is a Z-Wave Sensor. Tripple Click the Temper Switch on the backside to confirm inclusion, exclusion and association. Please refer to the chapters below for detailed information about all aspects of the products usage.
-
Page 2: Product Description
3. Sensors report change of status of measured values to controller 4. Sensors directly control actuators 5. Actuators control other actuators 6. Remote controls send signals to static controllers to trigger scenes or other actions 7. Remote controls control other actuators. There are two different role a controller can have. -
Page 3: Behavior Within The Z-Wave Network
Open the casing and dissemble the front part of the case. Put the included CR123A battery into the battery compartment and close the casing. The sensor consists of two parts; a Detector and a Magnet. They are designed to be fitted to doors or windows with the Magnet mounted on the opening part and the Detector mounted on the fixed frame. -
Page 4: Operating The Device
Operating the device Opening the protected door/window will remove the magnetic field, trigger the detector and generate an alarm condition, (if the system is armed). The sensor can also applied to automatic light control, one scenario is to get the illumination lux level from built in illumination sensors and send a signal to Z-Wave switch to turn the light on once we open the door when the room is dark. -
Page 5: Configuration Parameters
Configuration Parameters Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features. IMPORTANT: Controllers may only allow to configure signed values. In order to set values in the range 128 …... - Page 6 Multi-Sensor Function Switch (Parameter Number 6, Parameter Size 1) parameter to set the sensor functions Value Description Bit 0: Disable magnetic integrate illumination. Bit 1: Reserved, always 1. Bit 2: Reserved, always 1. Bit 3: Reserved. Bit 4: Disable delay 5 seconds to turn off the light, when door/window closed. 0 —...
-
Page 7: Command Classes
Auto Report Temperature Time (Parameter Number 13, Parameter Size 1) interval time for auto report the temperature Value Description 1 — 127 30 minutes per tick and minimum time is 30 minutes, default tick is 12 (6 hours) (Default 12) Command Classes Supported Command Classes Battery (version 1) -
Page 8: Disposal Guidelines
Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls. Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
Need help?
Do you have a question about the PSM01 and is the answer not in the manual?
Questions and answers