Xerox Phaser 790 Service Manual page 3

REP 8.22 Feeder Drive Unit/Low Paper Sensor .............................................................
REP 8.23 Paper Feeder Assembly .................................................................................
REP 8.24 Takeaway Clutch ............................................................................................
REP 8.25 Nudger Solenoid .............................................................................................
REP 8.26 Turn Clutch .....................................................................................................
REP 8.27 Duplex Tray Assembly ....................................................................................
REP 8.28 Duplex Entrance Sensor.................................................................................
REP 8.29 Duplex Exit Sensor .........................................................................................
REP 8.30 Duplex Drive Clutch ........................................................................................
REP 8.31 Front Belt ........................................................................................................
REP 8.32 Rear Belt .........................................................................................................
REP 8.33 Inverter Upper Assembly ................................................................................
REP 8.34 Exit Roll...........................................................................................................
REP 8.35 Inverter/Lower Assembly ................................................................................
REP 8.36 Inverter Motor .................................................................................................
REP 8.37 Inverter Sensor ...............................................................................................
REP 8.38 Duplex Controller PWB...................................................................................
REP 8.39 Duplex Nip Solenoid .......................................................................................
REP 8.40 Exit Transport Assembly .................................................................................
REP 8.41 Full Stack Sensor............................................................................................
REP 8.42 Exit Chute Interlock.........................................................................................
REP 8.43 Top Exit Sensor ..............................................................................................
Xerographics
REP 9.1 Copy/Print Cartridge .........................................................................................
REP 9.2 Waste Container ...............................................................................................
REP 9.3 ROS ..................................................................................................................
REP 9.4 ADC Sensor......................................................................................................
REP 9.5 Locating Rail .....................................................................................................
REP 9.6 Waste Toner Sensor.........................................................................................
REP 9.7 Toner Box Sensor .............................................................................................
REP 9.8 Erase Lamp ......................................................................................................
REP 9.9 Dry Ink Cartridge...............................................................................................
REP 9.10 Developer Housing .........................................................................................
REP 9.11 Rotary Sensor .................................................................................................
REP 9.12 Rotary Frame..................................................................................................
REP 9.13 Cartridge Sensor.............................................................................................
REP 9.14 Developer Tie Plate ........................................................................................
REP 9.15 Tension Lever .................................................................................................
REP 9.16 IBT Assembly..................................................................................................
REP 9.17 Belt Cleaner ....................................................................................................
REP 9.18 BTR 2 Assembly .............................................................................................
REP 9.19 BTR 2 Cam Assembly ....................................................................................
REP 9.20 Auger ..............................................................................................................
REP 9.21 IBT Belt ...........................................................................................................
REP 9.22 TR0 Sensor.....................................................................................................
REP 9.23 BTR 2 Cam Clutch ..........................................................................................
Fusing
REP 10.1 Fuser Assembly ..............................................................................................
REP 10.2 Main Fuser Assembly .....................................................................................
REP 10.3 Upper Guide Assembly ...................................................................................
Repairs and Adjustments
4-73 REP 10.4 Upper Plate .....................................................................................................
4-74 REP 10.5 Heat Roll Heat Lamp.......................................................................................
4-75 REP 10.6 Pressure Roll Heat Lamp................................................................................
4-75 REP 10.7 Lower Guide Assembly ...................................................................................
4-76 REP 10.8 Front Fuser Exit Sensor ..................................................................................
4-76 REP 10.9 Rear Fuser Exit Sensor...................................................................................
4-77 REP 10.10 Heat Roll .......................................................................................................
4-78 REP 10.11 Pressure Roll ................................................................................................
4-80 REP 10.12 Temperature Sensor .....................................................................................
4-80 REP 10.13 Exchange Chute ...........................................................................................
4-81 REP 10.14 Exchange Solenoid .......................................................................................
4-81 REP 10.15 Cleaner Cam Solenoid..................................................................................
4-82 REP 10.16 Cleaner Cam Shaft .......................................................................................
4-83 REP 10.17 Exit Roll.........................................................................................................
4-83 REP 10.18 Fuser Entrance Sensor .................................................................................
4-85 REP 10.19 Fuser Chute Fan ...........................................................................................
4-86
Sorter
4-87
REP 11.1 Sorter ..............................................................................................................
4-88
REP 11.2 Bottom Cover ..................................................................................................
4-89
REP 11.3 Sorter Control PWB ........................................................................................
4-89
REP 11.4 Sorter Transport Motor....................................................................................
4-90
REP 11.5 Sensor Receiver .............................................................................................
REP 11.6 Sensor Transmitter .........................................................................................
4-91 REP 11.7 Sorter Path Sensor .........................................................................................
4-91 REP 11.8 Full Sensor......................................................................................................
4-92 REP 11.9 Bin Drive Motor ...............................................................................................
4-94 REP 11.10 Front / Rear Gear Shaft ................................................................................
4-95 REP 11.11 Front / Rear Bin Cam ....................................................................................
4-96 REP 11.12 Bin Cam Switch.............................................................................................
4-96 REP 11.13 Bin Home Switch...........................................................................................
4-97 REP 11.14 Bin Tray(s) ....................................................................................................
4-97 REP 11.15 Docking Interlock ..........................................................................................
4-98
Covers
4-99
REP 14.1 Front Cover Assembly ....................................................................................
4-100
REP 14.2 Front Mid Cover ..............................................................................................
4-102
REP 14.3 Front Lower Cover ..........................................................................................
4-103
REP 14.4 Top Cover Assembly.......................................................................................
4-103
REP 14.5 Inner Covers ...................................................................................................
4-104
REP 14.6 Rear Cover......................................................................................................
4-105
REP 14.7 Filter ................................................................................................................
4-106
REP 14.8 Left Lower Cover.............................................................................................
4-107
REP 14.9 Right Cover .....................................................................................................
4-108
REP 14.10 Control Panel ................................................................................................
4-109
REP 14.11 Right Lower Cover ........................................................................................
4-111
4-111
Adjustments
ADJ 3.1 Hard Disk Drive Assembly.................................................................................
ADJ 3.2 ESS PWB Initialization ......................................................................................
4-113
ADJ 5.1 ADF Side Registration .......................................................................................
4-113
ADJ 5.2 ADF Lead Edge Registration.............................................................................
4-114
10/00
4-115
4-116
4-117
4-117
4-118
4-118
4-119
4-120
4-121
4-122
4-123
4-123
4-124
4-125
4-126
4-127
4-129
4-129
4-130
4-131
4-132
4-132
4-133
4-133
4-134
4-135
4-135
4-136
4-136
4-137
4-137
4-139
4-139
4-140
4-141
4-142
4-143
4-144
4-144
4-145
4-145
4-146
4-147
4-147
4-148
4-149
Initial Issue
Phaser 790/DocuColor 2006