Table of Contents
Advertisement
DVD-S49PC
9.2.
Service Mode Table 1
The service modes can be activated by pressing various button combination on the player and remote control unit.
Player buttons
Remote control unit buttons
PAUSE
+
OPEN/CLOSE
PAUSE
QUICK OSD
OPEN/CLOSE
9.3.
DVD Self Diagnostic Function-Error Code
Error Code
Error Content
U, H error
U11
Focus error
U15
Unfinalized DVD-R
H01
Tray loading error
H02
Spindle servo error
H03
Traverse servo error
H04
Tracking servo error
H05
Seek error
H06
Power error
H07
Spindle
error
DSC related
F500
DSC error
F501
DSC not Ready
F502
DSC Time out error
F503
DSC
Failure
F505
DSC Attention error
F506
Invalid media
ODC related
F600
Access
management
information caused by
demodulation error
F601
Indeterminate sector ID
requested
F602
Access failure to LEAD-
IN
caused
demodulation error
F603
Access
KEYDET
demodulation error
F610
ODC abnormality
0
Displaying the UHF display F_ _ _
5
Jitter check, tilt adjustment
*Display shows J_xxx/yyy_zz
"yyy" and "zz" shown to the right have nothing to do with the jitter
value. "yyy" is the error counter, while "zz" is the focus drive
value.
Refer to section 11.4. for Optical Pickup Tilt Adjustment
Procedure.
6
Checking the region numbers and broadcast system
7
Checking the program version
9
Lighting Confirmation Function of Display Tube
FUNCTION
Checking the laser drive current
PAUSE
Writing the laser drive current value after replacing the optical
pickup (do not use for anything other than optical pickup
replacement)
Initializing the DVD player
(restoring factory preset settings)
Additional error explanation
(Spindle servo, DV3.2 (IC8001) SP motor, CLV
servo error)
Cannot switch off the power because of the panel
and system computer communication error
motor
drive
DV3.2 (IC8001) stops in the occurence of servo
error (starup, focus error, etc)
DSC-system
computer
(Communication failure caused by idling of DSC)
Similar disposal as F500
communication
Communication
although communication command was sent)
Similar disposal as F500
Disc
is
flipped
incompatible disc
failure
to
Operation stopped because navigation data is not
accessible caused by the demodulation defect
Operation stopped caused by the request to
access abnormal ID data
LEAD IN data unreadable
by
failure
to
Access failure to CSS data of disc
caused
by
No permission for command execution
Application
communication
error
error
(result
error
occured
over,
TOC
unreadable,
22
Refer to section 9.3. Self-
Diagnosis Function (UHF
Display).
Refer to section 11.4.
Optical Pickup Tilt
Adjustment
Check the IC8651 FLASH
ROM program.
Refer to section 8
Optical Pickup
Replacement Procedure.
Refer to section 9.5.
Initializing the DVD
player.
Defect 1
Defect 2
Defect 3
Spindle
motor ass'y
Optical
DV3.2
servo drive
pickup
(IC8001)
DV3.2
(IC8001)
Optical
DV3.2
servo drive
pickup
(IC8001)
DV3.2
EEPROM
(IC8001)
(IC8611)
Optical
DV3.2
servo drive
pickup
(IC8001)
DISC
DV3.2
(IC8001)
DV3.2
(IC8001)
DV3.2
(IC8001)
DV3.2
(IC8001)
Note
Defect 4
Advertisement
Table of Contents
