Page 1
AXIS P3364-LV Network Camera Installation Guide...
Page 2
Low Voltage (LVD) Directive 2006/95/EC. See Safety Every care has been taken in the preparation of this on page 3. document. Please inform your local Axis office of any • Restrictions of Hazardous Substances (RoHS) Directive inaccuracies or omissions. Axis Communications AB cannot 2011/65/EU.
Page 3
FAQ database. ケーブル(STP)を使用して接続してください。また Search by product, category, or phrase 適切に接地してください。 • report problems to Axis support staff by logging in to your private support area Korea • chat with Axis support staff 이 기기는 가정용(B급) 전자파적합기기로서 주로...
AXIS P3364-LV Network Camera Safety Information Read through this Installation Guide carefully before installing the product. Keep the Installation Guide for future reference. Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
TICE • The Axis product shall be used in compliance with local laws and regulations. • To use the Axis product outdoors, or in similar environments, it shall be installed in an approved outdoor housing. • Store the Axis product in a dry and ventilated environment.
WARNING • Risk of explosion if the battery is incorrectly replaced. • Replace only with an identical battery or a battery which is recommended by Axis. • Dispose of used batteries according to local regulations or the battery manufacturer's instructions.
AXIS P3364-LV Network Camera Installation Guide This Installation Guide provides instructions for installing AXIS P3364-LV Fixed Dome Network Camera on your network. For other aspects of using the product, see the User Manual available at www.axis.com. Installation Steps 1. Make sure the package contents, tools and other materials necessary for the installation are in order.
AXIS P3364-LV Network Camera Hardware Overview Camera unit IR illumination Network connector (PoE) Audio out LED indicators Audio in I/O connector Control button Built-in microphone 10 SD memory card slot...
AXIS P3364-LV Network Camera 11 Fan output connector 12 Wall screw (x2) 13 Dome cover Mounting Bracket Note The mounting bracket is available as an optional accessory. LED Indicators Note • The Status LED can be configured to be unlit during normal operation. To configure, go to Setup >...
AXIS P3364-LV Network Camera Network LED Indication Green Steady for connection to a 100 Mbit/s network. Flashes for network activity. Amber Steady for connection to a 10 Mbit/s network. Flashes for network activity. Unlit No network connection. Power LED Indication Green Normal operation.
The control button is used for: • Resetting the product to factory default settings. See page 22. • Connecting to an AXIS Video Hosting System service or AXIS Internet Dynamic DNS Service. For more information about these services, see the User Manual. Specifications Operating Conditions The Axis product is intended for indoor use.
AXIS P3364-LV Network Camera Power Consumption Note Make sure the switch on the bottom of the camera is configured to PoE class 3. The IR illumination will not work if configured otherwise. Product AXIS P3364-LV Power over Ethernet IEEE 802.3af/802.3at Type 1 IR illumination on: Class 3;...
Install the Hardware Note • This Axis product can be mounted with the cables routed through or along the wall. • This product can be fitted with a metal conduit for protecting the cabling when the cables are routed along the wall.
4. Complete the Installation Replace Clear/Smoked Dome Cover (Optional) The Axis product is supplied with an optional dome. To replace the dome cover: 1. Loosen the four screws under the dome cover that hold the dome in place. 2. Replace the old dome with the new. Make sure the rubber gasket sits securely in place...
AXIS P3364-LV Network Camera Mount the Camera Directly onto Wall 1. Drill two holes in the wall using the drill template. 2. Route and connect all required cables. These include the network cable and may include external input/output devices and the active speaker/external microphone.
AXIS P3364-LV Network Camera Mounting bracket Network cable M4x8 screw Adjust the Position of the Lens The lens can be rotated and tilted to cover a certain area of interest and adjust the live view image. Rotate the Lens Note The marking on the lens cover is by default oriented facing upwards (wall mount).
Page 19
AXIS P3364-LV Network Camera Locking screw Lens holder Marking (design A) Marking (design B) 2. Loosen the locking screw. 3. Check the Live View page and turn the lens holder to rotate the lens 90° or 180°. 4. Once satisfied, gently tighten the locking screw to secure the lens holder’s position.
AXIS P3364-LV Network Camera Lens Screw Adjust Focus and Zoom NO TICE TICE TICE Adjusting focus and zoom manually can damage the lens. Note • Due to the dome’s refraction, the image may appear slightly out of focus once the dome has been placed.
Page 21
AXIS P3364-LV Network Camera Side lid Dome cover 2. Rotate the black shield inside the dome cover so it does not cover the lens. Black shield 3. Make sure the rubber gasket sits securely on the dome cover. 4. Clean the dome with a dry soft cloth to remove dust and finger prints and use a blower to remove dust from the lens.
AXIS P3364-LV Network Camera Access the Product AXIS IP Utility and AXIS Camera Management are recommended methods for finding Axis products on the network and assigning them IP addresses in Windows®. Both applications are free and can be downloaded from www.axis.com/techsup The product can be used with most operating systems and browsers.
AXIS P3364-LV Network Camera Visit www.axis.com/techsup to check if there is updated firmware available for your network product. To see the currently installed firmware version, go to Setup > About. Visit Axis learning center www.axis.com/academy for useful trainings, webinars, tutorials and guides.
AXIS P3364-LV Network Camera Informations sur la sécurité Lisez attentivement ce guide d'installation avant d'installer l'appareil. Conservez le guide d'installation pour toute référence ultérieure. Niveaux de risques DANGER Indique une situation dangereuse qui, si elle n'est pas évitée, entraînera le décès ou des blessures graves.
Page 26
• Le produit Axis doit être utilisé conformément aux lois et règlementations locales en vigueur. • Pour pouvoir utiliser le produit Axis à l'extérieur, ou dans des environnements similaires, il doit être installé dans un boîtier d'extérieur homologué. • Conserver ce produit Axis dans un environnement sec et ventilé.
AXIS P3364-LV Network Camera La batterie doit être remplacée uniquement en cas de besoin, et pour ce faire, contactez l'assistance technique d'Axis à l'adresse www.axis.com/techsup et obtenir de l'aide. AVERTISSEMENT • Risque d'explosion si la batterie est remplacée de façon incorrecte.
AXIS P3364-LV Network Camera Guide d'installation Ce guide d'installation explique comment installer la caméra réseau AXIS P3364-LV à dôme fixe sur votre réseau. Pour toute autre information relative à l’utilisation du produit, consultez le manuel de l’utilisateur disponible sur le site www.axis.com.
AXIS P3364-LV Network Camera Aperçu du matériel Caméra Éclairage IR Connecteur réseau (PoE) Sortie audio Voyants DEL Entrée audio Connecteur d'E/S Bouton de commande Microphone intégré...
Page 31
AXIS P3364-LV Network Camera 10 Logement pour carte mémoire SD 11 Connecteur de sortie de ventilateur 12 Vis murales (x 2) 13 Couvercle de dôme Support de fixation Note Le support de fixation est également disponible en option. Voyants Note •...
AXIS P3364-LV Network Camera Fixe pendant le démarrage et lors de la restauration des Orange paramètres. Rouge Clignote en rouge en cas d'échec de la mise à niveau du microprogramme. Indication Voyant DEL réseau Vert Fixe en cas de connexion à un réseau de 100 Mbits/s. Clignote en cas d’activité...
Page 33
Le bouton de commande permet de réaliser les opérations suivantes : • Réinitialisation du produit aux paramètres d’usine par défaut. Cf. page 43. • Connexion au service du Système d'hébergement vidéo AXIS ou au service AXIS Internet Dynamic DNS. Pour plus d'informations sur ces services, reportez-vous au Manuel de l'utilisateur.
AXIS P3364-LV Network Camera Caractéristiques techniques Conditions d’utilisation Le produit Axis est uniquement destiné à une utilisation en intérieur. Produit Classification Température Humidité AXIS P3364–LV IEC 62262 IK10 0 °C à 50 °C Humidité relative (32 °F à 122 °F) de 10 à...
Page 35
AXIS P3364-LV Network Camera Entrée Connectez-la à la broche 1 pour l’activer 0 à 40 V CC numérique ou laissez-la flotter (déconnectée) pour la désactiver. Sortie Connectée à la broche 1 lorsqu'elle est 0 à 40 V CC max., drain numérique...
AXIS P3364-LV Network Camera Schémas de connexion Connecteur d'E/S 0 V CC (-) Sortie CC 3,3 V, maxi. 50 mA Entrée numérique 0 à max. 40 V CC Entrée numérique 0 à max. 40 V CC, drain ouvert, max. 100 mA Installation du matériel...
Page 37
Remplacement du couvercle de dôme fumé ou non fumé (en option) La caméra Axis est fournie avec un dôme en option. Pour remplacer le couvercle du dôme : 1. sous le couvercle du dôme, dévissez les quatre vis qui maintiennent le dôme en place.
AXIS P3364-LV Network Camera 2. Orientez et connectez tous les câbles nécessaires. Les câbles nécessaires comprennent le câble réseau et peuvent inclure des dispositifs d’entrée/sortie et le haut-parleur actif/microphone externe. 3. Fixez la caméra au mur à l’aide de vis et de chevilles appropriées au matériau du mur.
Page 39
AXIS P3364-LV Network Camera Support de fixation Câble réseau Vis M4 x 8 Ajuster la position de l’objectif Vous pouvez pivoter l'objectif et l'incliner afin de couvrir une certaine zone d'intérêt et d'ajuster l'image en direct. Rotation de l'objectif Note La marque sur le couvercle de l’objectif est par défaut tournée vers le haut (support mural).
Page 40
AXIS P3364-LV Network Camera Vis de verrouillage Porte-objectif Marque (forme A) Marque (forme B) 2. Dévissez la vis de verrouillage. 3. Consultez la page Visualisation en direct et tournez le porte-objectif pour faire tourner l'objectif de 90° ou 180°. 4. Une fois que vous avez terminé, serrez délicatement la vis de verrouillage pour bien maintenir le porte-objectif en position.
Page 41
AXIS P3364-LV Network Camera Objectif Réglage de la mise au point et du zoom A A A VIS Le réglage manuel de la mise au point et du zoom peut endommager l’objectif. Note • Du fait de la réfraction du dôme, l'image peut apparaître légèrement floue une fois le dôme installé.
Page 42
AXIS P3364-LV Network Camera Couvercle latéral Couvercle de dôme 2. Tournez le bouclier noir à l'intérieur du boîtier du dôme de la caméra afin qu'il ne masque pas l'objectif. Bouclier noir 3. Assurez-vous que le joint en caoutchouc est correctement placé sur le couvercle du dôme.
AXIS P3364-LV Network Camera Utilisez le produit Si vous souhaitez rechercher des produits Axis sur le réseau ou leur affecter des adresses IP sous Windows®, nous recommandons l’utilisation des applications AXIS IP Utility et AXIS Camera Management. Ces deux applications sont gratuites et peuvent être téléchargées depuis www.axis.com/techsup...
Pour connaître la version du microprogramme actuellement installée, reportez-vous à la page Setup > About (Configuration > À propos de). Visitez le centre de formation en ligne Axis sur le site www.axis.com/academy pour en savoir plus sur les formations, les webinaires, les tutoriels et les guides.
AXIS P3364-LV Network Camera Sicherheitsinformation Lesen Sie das Installationshandbuch sorgfältig durch bevor sie das Produkt installieren. Bewahren Sie das Installationshandbuch für zukünftige Zwecke auf. Gefährdungsstufen GEFAHR Weist auf eine gefährliche Situation hin, die, falls nicht verhindert, zu Tod oder schweren Verletzungen führt.
Page 46
Produkts, wenn ein Batteriewechsel erforderlich ist. Weitere Informationen über den Serverbericht finden Sie auf den Setup-Seiten des Produkts, oder wenden Sie sich an den Axis Support. Die Batterie sollte nur bei Bedarf ersetzt werden. Wenden Sie sich in diesem Fall an den Axis Support unter www.axis.com/techsup.
Page 47
AXIS P3364-LV Network Camera WARNUNG • Explosionsgefahr bei fehlerhaftem Batteriewechsel. • Die Batterie darf nur durch eine identische Batterie oder eine von Axis empfohlene Batterie ersetzt werden. • Verbrauchte Batterien sind gemäß den örtlichen Vorschriften oder den Anweisungen des Herstellers zu entsorgen.
AXIS P3364-LV Network Camera Installationsanleitung In dieser Anleitung wird die Installation der unbeweglichen AXIS P3364-LV Dome-Netzwerk-Kamera in Ihrem Netzwerk beschrieben. Weitere Informationen zur Verwendung dieses Produktes finden Sie im Benutzerhandbuch unter www.axis.com. Installationsschritte 1. Stellen Sie sicher, dass die Packungsinhalte, Werkzeuge und andere notwendige Materialien für die Installation in Ordnung sind.
AXIS P3364-LV Network Camera Übersicht über die Hardware Kameraeinheit IR-Beleuchtung Netzwerkanschluss (PoE) Audioausgang LED-Anzeigen Audioeingang E/A-Anschluss Steuertaste Eingebautes Mikrofon...
Page 51
AXIS P3364-LV Network Camera 10 SD-Speicherkarteneinschub 11 Lüfterausgangsanschluss 12 Wandschrauben (2x) 13 Kuppelabdeckung Montagehalterung Beachten Die Montagehalterung ist als optionales Zubehör erhältlich. LEDs Beachten • Die Status-LED kann so eingestellt werden, dass sie während des Normalbetriebs nicht leuchtet. Diese Konfiguration können Sie unter Setup > System Options > Ports &...
Page 52
AXIS P3364-LV Network Camera Netzwerk-LED Bedeutung Grün Leuchtet bei Verbindung mit einem 100 MBit/s-Netzwerk. Blinkt bei Netzwerkaktivität. Gelb Leuchtet bei Verbindung mit einem 10 MBit/s-Netzwerk. Blinkt bei Netzwerkaktivität. Leuchtet nicht Keine Netzwerkverbindung vorhanden. Netz-LED Bedeutung Grün Normaler Betrieb. Gelb Blinkt grün/gelb bei der Firmware-Aktualisierung.
Die Steuertaste hat folgende Funktionen: • Zurücksetzen des Produkts auf die Werkseinstellungen. Siehe Seite 63. • Verbinden mit einem AXIS Video Hosting System-Service oder einem AXIS Internet Dynamic DNS-Service. Weitere Informationen zu diesen Diensten finden Sie in der Bedienungsanleitung. Technische Daten Betriebsbedingungen Das Axis Produkt ist für die Verwendung in Innenräumen konzipiert.
Page 54
AXIS P3364-LV Network Camera Produkt Temperatur Klassifikation Luftfeuchtigkeit AXIS P3364–LV IEC 62262 IK10 0 °C bis 50 °C 10–85 % rF (nicht kondensierend) Stromverbrauch Beachten Stellen Sie sicher, dass der Schalter an der Kameraunterseite auf PoE Klasse 3 eingestellt ist.
Page 55
AXIS P3364-LV Network Camera Digital- Zum Aktivieren mit Pin 1 verbinden; 0 bis max. 40 V DC eingang zum Deaktivieren nicht anschließen. Digital- Bei Aktivierung mit Pin 1 verbunden; 0 bis max. 40 V DC, Open ausgang wenn deaktiviert: frei (nicht Drain, 100 mA verbunden).
Digitalausgang 0 bis max. 40 V DC, Open Drain, 100 mA Installieren der Hardware Beachten • Bei der Montage dieses Axis Produkts können Sie die Kabel entweder durch die Wand oder entlang der Wand führen. • Sie können die Netzwerk-Kamera mit einer Kabelführung aus Metall zum Schutz der Kabel...
3. Einstellen von Fokus und Zoom 4. Abschluss der Installation Austauschen der klaren/getönten Kuppelabdeckung (optional) Das Axis Produkt wird mit einer optionalen Kuppel geliefert. So tauschen Sie die Kuppelabdeckung aus: 1. Lösen Sie die vier Schrauben unter der Kuppelabdeckung, die die Kuppel an ihrer Position halten.
AXIS P3364-LV Network Camera Montage der Kamera direkt an der Wand 1. Bohren Sie mithilfe der Bohrschablone zwei Löcher in die Wand. 2. Verlegen Sie alle benötigten Kabel und schließen Sie sie an. Hierzu gehören das Netzwerkkabel sowie die Kabel für externe Eingabe-/Ausgabegeräte und für den Aktivlautsprecher bzw.
AXIS P3364-LV Network Camera Die Abbildung zeigt ein Modell ohne IR-Beleuchtung. Montagehalterung Netzwerkkabel M4x8-Schraube Einstellen der Objektivposition Das Objektiv kann gedreht und gekippt werden, sodass ein ausgewählter Bereich als Live-Bild dargestellt wird. Drehen des Objektivs Beachten Die Markierung auf der Objektivabdeckung weist standardmäßig nach oben (Wandmontage).
Page 60
AXIS P3364-LV Network Camera Feststellschraube Objektivhalter Markierung (Ausführung A) Markierung (Ausführung B) 2. Lösen Sie die Feststellschraube. 3. Überprüfen Sie die Seite Live View (Live-Ansicht) und drehen Sie den Objektivhalter und damit das Objektiv auf 90° bzw. 180°. 4. Wenn die richtige Ausrichtung erreicht ist, schrauben Sie die Feststellschraube vorsichtig wieder fest, um den Objektivhalter zu arretieren.
AXIS P3364-LV Network Camera Objektiv Schraube Einstellen von Fokus und Zoom HINWEIS HINWEIS HINWEIS Durch das manuelle Einstellen von Fokus und Zoom kann das Objektiv beschädigt werden. Beachten • Aufgrund der Lichtbrechungen auf der Glasoberfläche kann das Bild leicht unscharf erscheinen, nachdem die Kuppel installiert wurde.
Page 62
AXIS P3364-LV Network Camera Seitenabdeckung Kuppelabdeckung 2. Bringen Sie das schwarze Schild in der Kuppel so an, dass es das Objektiv nicht verdeckt. Schwarzes Schild 3. Vergewissern Sie sich, dass die Gummidichtung fest an der Kuppelabdeckung angebracht ist. 4. Entfernen Sie Fingerabdrücke und Staub von der Glasoberfläche mit einem trockenen, weichen Tuch.
AXIS P3364-LV Network Camera Zugriff auf das Produkt Für die Suche nach Axis Produkten im Netzwerk und zur Zuweisung einer IP-Adresse unter Windows® werden AXIS IP Utility und AXIS Camera Management empfohlen. Beide Anwendungen sind kostenlos und können von unserer Website unter www.axis.com/techsup heruntergeladen werden.
Unter www.axis.com/techsup finden Sie Firmware-Aktualisierungen für Ihre Netzwerkprodukte. Um die aktuell installierte Firmware-Version zu sehen, gehen Sie auf Einrichten > Über. Besuchen Sie das Axis-Schulungszentrum www.axis.com/academy für anregende Schulungen, Webinare, Lernprogramme und Anleitungen. Gewährleistung Informationen zur Gewährleistung der Axis Produkte und hierzu verbundene Informationen, finden Sie unter www.axis.com/warranty/...
AXIS P3364-LV Network Camera Informazioni di sicurezza Leggere con attenzione questa guida all'installazione prima di installare il dispositivo. Conservare questo documento per usi futuri. Livelli di pericolo PERICOLO Indica una situazione pericolosa che, se non evitata, provoca morte o lesioni gravi.
Page 66
• Durante il trasporto del dispositivo Axis, utilizzare l'imballaggio originale o equivalente per evitare danni al dispositivo. Batteria Il prodotto Axis utilizza una batteria al litio da 3,0 V BR/CR2032 come alimentazione per il suo real-time clock (RTC) interno. In condizioni normali questa batteria avrà una durata minima di cinque anni.
Page 67
• Rischio di esplosione se la batteria viene sostituita in modo errato. • Sostituire solo con una batteria identica o una batteria consigliata da Axis. • Smaltire le batterie usate in base alle normative locali o alle istruzioni del produttore della batteria.
Guida all'installazione La presente Guida all'installazione fornisce le istruzioni necessarie per installare la telecamera di rete a cupola fissa AXIS P3364-LV nella rete in uso. Per ulteriori informazioni sull'utilizzo del dispositivo, consultare la Guida per l'utente disponibile all'indirizzo www.axis.com. Procedure di installazione 1.
AXIS P3364-LV Network Camera Panoramica dell'hardware Unità telecamera Illuminazione IR Connettore di rete (PoE) Uscita audio Indicatori LED Ingresso audio Connettore I/O Pulsante di comando Microfono incorporato 10 Alloggiamento per schede di memoria SD...
AXIS P3364-LV Network Camera 11 Connettore di alimentazione in uscita ventola 12 Vite per il montaggio a parete (x2) 13 Copertura a cupola Staffa di montaggio Nota La staffa di montaggio è disponibile come accessorio opzionale. Indicatori LED Nota • Lo stato del LED può essere configurato per essere spento durante il normale funzionamento.
AXIS P3364-LV Network Camera LED di rete Indicazione Verde Luce fissa per connessione di rete a 100 Mbit/s. Luce lampeggiante: attività di rete. Giallo Luce fissa per connessione di rete a 10 Mbit/s. Luce lampeggiante: attività di rete. Spento Assenza di connessione.
• Ripristino del dispositivo alle impostazioni predefinite di fabbrica. Consultare pagina 83. • Collegamento a un servizio AXIS Video Hosting System o AXIS Internet Dynamic DNS Service. Per ulteriori informazioni su questi servizi, consultare il Manuale Utente. Dati tecnici Condizioni di funzionamento...
AXIS P3364-LV Network Camera Dispositivo Classificazione Temperatura Umidità AXIS P3364–LV IEC 62262 IK10 Da 0 °C a 50 °C 10-85% umidità (da 32 °F a 122 °F) relativa (senza condensa) Consumo energetico Nota Assicurarsi che lo switch sul fondo della telecamera sia configurato su PoE classe 3.
Page 75
AXIS P3364-LV Network Camera Ingresso Collegare al pin 1 per attivarlo oppure Da 0 a max 40 V CC digitale lasciarlo isolato (scollegato) per disattivarlo Uscita Collegare al pin 1 quando attiva, isolata Da 0 a max 40 V CC, digitale (scollegata) quando inattiva.
Ingresso digitale da 0 a max 40 V CC, open-drain, 100 mA Installazione dell'Hardware Nota • Questo dispositivo Axis può essere montato installando i cavi attraverso la parete o lungo di essa. • Questo dispositivo può essere munito di una canalina metallica per proteggere i cavi nel caso in cui vengano installati lungo la parete.
4. Completamento dell'installazione Sostituzione della copertura della cupola trasparente/fumé(opzionale) Il dispositivo Axis viene fornito con una cupola opzionale. Per sostituire la copertura a cupola: 1. Allentare le quattro viti che fissano la cupola in posizione sotto la copertura. 2. Sostituire la cupola esistente con quella nuova. Assicurarsi che la guarnizione in gomma sia ben salda e serrare le viti.
Page 78
AXIS P3364-LV Network Camera 2. Collegare tutti i cavi richiesti, incluso il cavo di rete e talvolta anche i collegamenti a dispositivi di input/output esterni e all'altoparlante attivo/microfono esterno. 3. Fissare la telecamera alla parete utilizzando viti e tasselli idonei al materiale della parete.
Page 79
AXIS P3364-LV Network Camera Staffa di montaggio Cavo di rete Vite M4x8 Regolazione della posizione dell'obiettivo L'obiettivo può essere ruotato e inclinato per coprire una determinata area di interesse e regolare le immagini dal vivo. Rotazione dell'obiettivo Nota Il contrassegno sul coperchio dell'obiettivo è orientato verso l'alto per impostazione predefinita (montaggio a parete).
Page 80
AXIS P3364-LV Network Camera Vite di arresto Porta-obiettivo Contrassegno (design A) Contrassegno (design B) 2. Allentare la vite di arresto. 3. Controllare la pagina Live View (Immagini dal vivo) e girare il porta-obiettivo per ruotare l'obiettivo di 90° o 180°.
AXIS P3364-LV Network Camera Obiettivo Vite Regolazione della messa a fuoco e dello zoom A A A VVISO VVISO VVISO La regolazione manuale della messa a fuoco e dello zoom può danneggiare l'obiettivo. Nota • Una volta montata la cupola, l'immagine potrebbe apparire leggermente sfocata a causa della rifrazione.
Page 82
AXIS P3364-LV Network Camera Copertura laterale Copertura a cupola 2. Ruotare lo schermo nero all'interno della copertura a cupola affinché non copra l'obiettivo. Schermo nero 3. Assicurarsi che la guarnizione in gomma sia ben salda sulla copertura a cupola. 4. Pulire la cupola con un panno morbido e asciutto per rimuovere polvere e impronte digitali;...
AXIS P3364-LV Network Camera Accedere al dispositivo AXIS IP Utility e AXIS Camera Management sono i metodi consigliati per trovare i dispositivi Axis in rete e assegnare loro un indirizzo IP in Windows®. Queste applicazioni sono entrambe gratuite e possono essere scaricate da www.axis.com/techsup Il dispositivo può...
Setup (Impostazioni) > About (Informazioni su). Visitare il centro di apprendimento Axis alla pagina www.axis.com/academy per servizi di formazione utili, webinar, tutorial e guide. Informazioni sulla garanzia Per informazioni sulla garanzia del dispositivo Axis e informazioni ad esso relative, consultare la pagina www.axis.com/warranty/...
AXIS P3364-LV Network Camera Información de seguridad Lea esta Guía de instalación con atención antes de instalar el producto. Guarde la Guía de instalación para poder consultarla en otro momento. Niveles de peligrosidad PELIGRO Indica una situación peligrosa que, si no se evita, provocará...
Batería Este producto de Axis utiliza una batería de litio BR/CR2032 de 3,0 V como fuente de alimentación del reloj interno en tiempo real. En condiciones normales, esta batería durará un mínimo de cinco años.
Page 87
ADVERTENCIA • La sustitución incorrecta de la batería implica riesgo de explosión. • Sustituya la batería por una batería idéntica u otra batería recomendada por Axis. • Deseche las baterías usadas de conformidad con la normativa local o las instrucciones del fabricante.
Guía de instalación Esta Guía de instalación incluye las instrucciones necesarias para instalar la cámara de red domo fija AXIS P3364-LV en su red. Para conocer otros aspectos de uso del producto, consulte el Manual del usuario, disponible en www.axis.com.
AXIS P3364-LV Network Camera Información general del hardware Unidad de cámara Iluminación de infrarrojos Conector de red (PoE) Salida de audio Indicadores LED Entrada de audio Conector de E/S Botón de control Micrófono integrado...
AXIS P3364-LV Network Camera 10 Ranura de tarjeta de memoria SD 11 Conector de salida del ventilador 12 Tornillos para la pared (2) 13 Cubierta del domo Soporte de montaje Nota El soporte de montaje se encuentra disponible como accesorio opcional.
AXIS P3364-LV Network Camera LED de red Indicación Verde Fijo para indicar una conexión a una red de 100 Mbits/s. Parpadea cuando hay actividad de red. Fijo para indicar una conexión a una red de 10 Mbits/s. Parpadea Ámbar cuando hay actividad de red.
Restablecer el producto a la configuración predeterminada de fábrica. Vea página 103. • Conectarse a un servicio AXIS Video Hosting System o al Servicio de DNS dinámico de Internet de AXIS. Para obtener más información sobre estos servicios, consulte el Manual del usuario.
Page 94
AXIS P3364-LV Network Camera Producto Temperatura Humedad Clasificación AXIS P3364-LV IEC 62262 IK10 De 0 °C a 50 °C Humedad relativa del 10 al 85 % (sin condensación) Consumo Nota Asegúrese de que el conmutador de la parte inferior de la cámara esté configurado en PoE Clase 3.
Page 95
AXIS P3364-LV Network Camera Entrada Conéctela al pin 1 para activarla o déjela De 0 a 40 V CC máx. digital suelta (desconectada) para desactivarla Salida digital Conectada al pin 1 cuando se activa y suelta De 0 a 40 V CC máx., (sin conectar) cuando está...
Salida digital: de 0 a 40 V CC máx., colector abierto, 100 mA Instalación del hardware Nota • Este producto de Axis puede montarse tendiendo los cables a través de la pared o sobre esta. • Este producto también puede equiparse con un conducto metálico para proteger el cableado cuando se tiende sobre la pared.
Sustitución de la cubierta del domo transparente/ahumada (opcional) El producto de Axis se suministra con una cubierta opcional. Para sustituir la cubierta del domo: 1. Afloje los cuatro tornillos de debajo de la cubierta del domo que fijan el domo en su posición.
AXIS P3364-LV Network Camera 2. Tienda y conecte todos los cables necesarios. Se incluye el cable de red y puede incluir dispositivos de entrada/salida externos y el micrófono externo/altavoz activo. 3. Conecte la unidad de cámara a la pared mediante los tornillos y tacos apropiados para el material de que esté...
Page 99
AXIS P3364-LV Network Camera Soporte de montaje Cable de red Tornillo M4x8 Ajuste de la posición del objetivo El objetivo se puede girar e inclinar para cubrir una determinada área de interés y ajustar la imagen de la vista en directo.
Page 100
AXIS P3364-LV Network Camera Tornillo de bloqueo Soporte del objetivo Marca (diseño A) Marca (diseño B) 2. Afloje el tornillo de bloqueo. 3. Consulte la página Live View (Vista en directo) y gire el soporte del objetivo para girar el objetivo 90° o 180°.
AXIS P3364-LV Network Camera Objetivo Tornillo Ajuste del enfoque y del zoom A A A VISO VISO VISO Si se ajustan el enfoque y el zoom manualmente, pueden producirse daños en el objetivo. Nota • Debido a la refracción del domo, la imagen puede aparecer ligeramente desenfocada una vez colocado.
Page 102
AXIS P3364-LV Network Camera Tapa lateral Cubierta del domo 2. Gire la cubierta de protección negra dentro de la cubierta del domo para que no cubra el objetivo. Cubierta protectora negra 3. Asegúrese de que la junta de goma se asienta correctamente sobre la cubierta del domo.
Acceso al producto Se recomiendan AXIS IP Utility y AXIS Camera Management como métodos para buscar los productos de Axis en la red y asignarles direcciones IP en Windows®. Ambas aplicaciones son gratuitas y pueden descargase de www.axis.com/techsup El producto se puede utilizar con la mayoría de los sistemas operativos y navegadores. Los navegadores recomendados son ®...
Visite el centro de aprendizaje de www.axis.com/academy para consultar guías, tutoriales, seminarios web y cursos que pueden resultarle útiles. Información de garantía Para obtener más detalles sobre la garantía del producto Axis y la información relacionada con ella, consulte www.axis.com/warranty/...
Page 115
AXIS P3364-LV Network Camera 3.3 V DC DC出力 補助装置の電源供給に使用できます。 最大負荷 = 50 mA 注: このピンは、電源出力としての み使用できます。 動作させるにはピン1に接続し、動作 0~40 V DC (最大) デジタル入 力 させない場合はフロート状態 (未接続) のままにします。 デジタル出 動作させるにはピン1に接続し、動作 0~40 V DC (最大)、 させない場合はフロート状態 (未接続) オープンドレイ 力 にします。 誘導負荷 (例: リレー) とと...
Page 116
AXIS P3364-LV Network Camera 接 接 接 続 続 続 図 図 図 I/O コ コ コ ネ ネ ネ ク ク ク タ タ タ 0 V DC (‑) DC出力3.3 V、最大50 mA デジタル出力0~最大40 V DC デジタル出力0~40 V DC (最大)、オープンドレイン、100 mA ハ...