Cables And Flexible Leaders; Tools And Replacement Blades; Machine Assembly; Instructions For Installing Handle - RIDGID K-7500 Manual

• K-7500 Machine with AUTOFEED, toolbox, stan-
dard tools and C-24 Cable (

Cables and Flexible Leaders

Catalog Model
No. No.
92460 C-25
92465 C-26
92470 C-27
" (16mm)
5 /
8 43647 C-24
32737 C-27HC
58192 C-24HC
" (16mm)
5 /
8
95762 C-25 IW
95757 C-26 IW
95752 C-27 IW
" (16mm)
5 /
95747 C-24 IW
8
92475 C-28
92480 C-29
41212 C-75
" (20mm)
3 / 41697 C-100
4
47427 C-75HC
47432 C-100HC
" (20mm)
3 /
4
92555 T-458
92560 T-468
44122 —
44117 —
Tools and Replacement Blades — Fits C-24,
C-25, C-26, C-27,C-28, C-29, C-75, C-100,
C-24HC, C-27HC, C-75HC and C-100HC
Catalog Model
No. No. Description
P-Trap Cutter, 3"
92485 T-403
92490 T-404 P-Trap Cutter, 3
92495
T-406 Spear Blade
92500 T-407 Retrieving Auger
92505 T-408 Sawtooth Cutter
51762
T-409 H-D Bulb Auger
92510 Double Cutter, 2"
T-411
92515
T-412 Double Cutter, 2
92520
T-413 Double Cutter, 3"
92525
T-414 Double Cutter, 4"
92530 T-416 Double Cutter, 6"
92535
T-432 3-Blade Cutter, 2"
92540 T-433 3-Blade Cutter, 3"
92545 T-434 3-Blade Cutter, 4"
92550 3-Blade Cutter, 6"
T-436
" x 100' Inner-Core)
5 /
8
Description
25' I.C. Cable (7,6m)
50' I.C. Cable (15,2m)
75' I.C. Cable (22,9m)
100' I.C. Cable (30,5m)
75' Hollow-Core (22,9m)
100' Hollow-Core (30,5m)
25' I.W. Cable (7,6m)
50' I.W. Cable (15,2m)
75' I.W. Cable (22,9m)
100' I.W. Cable (30,5m)
25' I.C. Cable (7,6m)
50' I.C. Cable (15,2m)
75' I.C. Cable (22,9m)
100' I.C. Cable (30,5m)
75' Hollow-Core (22,9m)
100' Hollow-Core (30,5m)
" x 2' Leader
5 /
8
" x 2' Leader
3 /
4
" Pigtail
5 /
8
" Pigtail
3 /
4
Replacement
Blade(s) Holder*
92835 92900
"
1 / 92840 92900
2
92850 92915
— —
92890 92915
— —
92815 92905
"
1 / 92820 92905
2
92825 92910
92830 92910
92855 92910
92860 92895
92865 92895
92870 92895
92875 92895
K-7500 Drain Cleaning machine
Blade
Blade
Holder
Coupling*
Figure 2 – Tool Assembly

Machine Assembly

WARNING
To prevent serious injury, proper assembly of the
Drain Cleaner is required. The following procedures
should be followed:

Instructions for Installing Handle

Raise the stair climber to the upper position by pulling out
the locking pin and lifting the stair climber by the cross
member until the pin locks into the upper position (Figure
3). Insert handle through the motor table rail supports and
through the two holes on rear support (Figure 4) . Insert the
two hairpin cotter fasteners through the holes in the bot-
tom of the handle (Figure 5) . Adjust handle to desired
height. Securely tighten the two T-shaped mounting
knobs on rear support. Lower the stair climber.
Figure 3 – Raising Stair Climbers
Fastener*
* Identifies components
included with holder
5