Description, Specifications And Standard Equipment Description; Specifications; Standard Equipment - RIDGID K-7500 Manual

K-7500 Drain Cleaning Machine
• Do not operate machine if operator or machine is
standing in water. Will increase the risk of electrical
shock.
• Wear safety glasses and rubber soled, non-slip
shoes. Use of this safety equipment may prevent se-
rious injury.
• Only use the K-7500 to clean drain lines 4" to 10" in
diameter. Follow instructions on the use of the
machine. Other uses or modifying the drain cleaner for
other applications may increase the risk of injury.
Description, Specifications and

Standard Equipment

Description
The RIDGID K-7500 Drain Cleaning Machine will clean
drain lines 4" to 10" in diameter and up to 250 feet in
length. The 4 / HP universal motor spins
10
at 200 RPM. When the cable hits the blockage, the motor
gears down automatically to deliver greater power and en-
hance operator control.
The molded polyethylene drum includes an inner drum that
guards against cable flip over. An integral Ground Fault
Interrupter (GFCI) is built into the line cord and a "kick-
stand" base is provided for machine stability during
operation. A pneumatic foot actuator provides ON/OFF
control of the motor.
" or
The drum powers a 5 /
8
change coupling system for connecting or disconnecting
tools. The cable is fed in an out of the drain by a AUTO -
FEED™ assembly at a rate of 0-28 feet/min.

Specifications

Line Capacity.................Generally recommended for
Recommended Line Size and Reach
Cable Size
& Type Line Size
5/8" Hollow-Core 3" to 4"
5/8" Inner-Core 3" to 4"
5/8" Solid Core 3" to 6"
3/4" Hollow-Core 4" to 6"
3/4" Inner-Core 4" to 10"
Figure 1
NOTE! 3/4" Inner-core is not recommended for use through
P-Trap and severe bends in lines smaller than 4".
Drum Capacity .............125' of
150' of
4
" and " cable
5 / 3 /
8 4
" cable that has a quick
3 /
4
all drain lines 4" to 10" but de-
pends on choice of cable.
Refer to the following chart for
specifics.
Reach
250'
250'
250'
250'
250'
" Cable,
3 /
4
" Cable
5 /
8
Motor Type ...................115V 60Hz Reversible,
Universal AC Motor
Rating: .......................... 4 /
AMPS ............................6.0
Weight
(Machine Only).............116 lbs.
Width ............................21"
Length ..........................31"
Standard Equipment
" Cable
For 3 /
4
• K-7500 Machine with AUTOFEED, toolbox and stan-
dard tools which include:
– 1 Pair Work Gloves
– T-403 P-Trap Cutter, 3"
– T-406 Spear Blade
– T-407 Retrieving Auger
– T-408 Sawtooth Cutter
– T-411 Double Cutter, 2"
– T-413 Double Cutter, 3"
– T-414-B Double Cutter Blade Only, 4"
– T-416-B Double Cutter Blade Only, 6"
" Flexible Leader
– T-468 3 /
4
– 4 Spacers for AUTOFEED adjustment
" Hex Key
– 3 /
16
• K-7500 Machine with AUTOFEED, toolbox, standard
tools and C-100 Cable (
• K-7500 Machine with AUTOFEED, toolbox, standard
tools and C-75 Cable (
• K-7500 Machine with AUTOFEED, toolbox, standard
tools and C-100 Cable HC (
• K-7500 Machine with manual feed, standard tools
• K-7500 Machine with manual feed, toolbox, standard
tools and C-100 Cable (
• K-7500 Machine with manual feed, toolbox, standard
tools and C-100 HC Cable (
" Cable
For 5 /
8
• K-7500 Machine with AUTOFEED, toolbox and stan-
dard tools which include:
– 1 Pair Work Gloves
– T-403 P-Trap Cutter, 3"
– T-406 Spear Blade
– T-407 Retrieving Auger
– T-408 Sawtooth Cutter
– T-411 Double Cutter, 2"
– T-413 Double Cutter, 3"
– T-414-B Double Cutter Blade Only, 4"
" Flexible Leader
– T-458 5 /
8
" Hex Key
– 3 /
16
HP, 200 RPM
10
" x 100' Inner-Core)
3 /
4
" x 75' Inner-Core)
3 /
4
" x 100' Hollow-Core)
3 /
4
" x 100' Inner-Core)
3 /
4
" x 100' Hollow-Core)
3 /
4