Panasonic SC-HT1500 Operating Instructions Manual page 11

Í/I
CHX, CHW
REC
RDS TIME SLIP CH CH
PULL-OPEN
Í
HDD
1
Numbered
4
buttons
7
STOP
DIRECT NAVIGATOR
TOP MENU
3 4 2 1
ENTER
FM MODE
SUB MENU
AV2/OPT
PROG/CHECK PROG/CHECK
TIME SLIP
EXT LINK
A
SHIFT SHIFT
Auto-Setup
(Setup without Q Link functions)
≥When connecting to a television with the VIDEO OUT, S-
VIDEO OUT or COMPONENT VIDEO OUT terminal (➡page 8).
≥When connecting to a television that does not have the Q
Link function (➡Operations Guide, page 55).
This unit's Auto-Setup function automatically tunes all available TV stations
and synchronizes the time and date with that of the receiving station after
tuning is completed.
≥When connecting to a television with RF socket only
(➡page 7)
1
Turn on the television and select the
appropriate AV input to suit the
connections to this unit.
2
Press [Í] to turn the unit on.
Auto-Setup starts. This takes about 5 minutes.
Auto-Setup
Ch 1
Auto-Setup in progress, please wait.
RETURN: to abort
RETURN
VOLUME
OPEN/CLOSE
TUNE
INPUT SELECTOR
HDD DVD FM/AM AUX
DOWN UP
HOME THEATER TV
DISPLAY
DIRECT TV REC AV
DVD FM/AM AUX
2 3
CH
5 6
VOLUME
8 9
CANCEL HDD/DVD INPUT
0 -/--
SKIP SLOW/SEARCH
PAUSE PLAY/
FUNCTIONS
ENTER
CH SELECT
RETURN
RETURN
MIX
2CH
TEST
PRO LOGIC
STATUS MANUAL SKIP VIDEO Plus +
TIMER ERASE REC
F
MULTI REAR S.POSITION C.FOCUS
DUBBING CREATE CHAP REC MODE
B C D
AUDIO REPEAT
EQ/SFC
MUTING
S W. LEVEL
(When connecting to a television with RF socket only)
Set the new RF output channel to TV (refer to the instructions for your TV).
Select an unused channel pre-set on your TV and tune it to the RF
output channel number shown on the unit's display.
(When the Auto-Setup screen does not appear clearly even after
performing the above operations, re-tune the channel until the Auto-
Setup screen becomes clear.)
3
When Auto-Setup has been
completed, the Owner ID
settings screen appears.
Press [1] and
press the
numbered buttons
to enter a 4-digit
PIN number.
≥Make a note of the PIN number (don't forget), as it is not possible to
return to the factory preset.
4
Press [ENTER] twice to store the PIN
number.
The cursor moves to "Name".
5
Press [1].
6
Press [3, 4] to select a letter and then
press [1].
Repeat this to enter the name.
7
Press [ENTER] to store the name.
8
Press [4] and [1], and then repeat steps
6, 7 to enter and store "House No." and
"Postcode".
9
Press [RETURN].
The Owner ID settings screen disappears.
To stop partway
Press [RETURN].
∫ If the clock setting menu appears
Set the clock manually (➡ Operations Guide, page 52).
∫ To confirm that stations have been tuned correctly
(➡Operations Guide, page 51)
∫ To restart Auto-Setup (➡Operations Guide, page 51)
You can also use the following method to restart Auto-Setup.
When the unit is on and stopped
Press and hold [X CH] and [CH W] on the main unit for about 5
seconds.
≥All the settings except for the ratings level, ratings password, Owner ID
and time settings return to the factory preset. The timer recording
programmes are also cancelled.
[When connecting to a television with RF socket only (➡ page 7)]
∫ To enter the satellite station's name (➡Operations
Guide, page 51)
The name of the satellite station is not set automatically. ("-- ---" will appear
under "Name" in the program list). After Auto-Setup is completed, enter the
name manually.
∫ If you connect other equipment to AV2 terminal of this
unit
Change the "AV2 Input" and "AV2 Connection" in the SETUP menu to
match the connected equipment (➡Operations Guide, page 50).
11
Owner ID
¢¢¢¢
PIN number
Name
House No.
Postcode
RETURN
RETURN : leave