Download
Share
Print this page
Clay Paky ALPHA SPOT HPE 1500 Instruction Manual
  1. Manuals
  2. Brands
  3. Clay Paky Manuals
  4. Lighting Equipment
  5. ALPHA SPOT HPE 1500
  6. Instruction manual

Clay Paky ALPHA SPOT HPE 1500 Instruction Manual

Hide thumbs Also See for ALPHA SPOT HPE 1500:

Advertisement

Quick Links

Download this manual See also: Instruction Manual
INDEX
Pag.
Contents
2
Safety information
3
Unpacking and preparation
4
Installation and start-up
5
Control panel
7
Menu setting
14
Maintenance
22
Technical information
22
Cause and solution of problems
23
Channel functions
ALPHA SPOT HPE 15
INSTRUCTION MANUAL
Congratulations on choosing a Clay Paky product
We thank you for your custom.
Please note that this product, as all the others in the rich Clay
Paky range, has been designed and made with total quality to
ensure excellent performance and best meet your expectations
and requirements.
Carefully read this instruction manual in its entirety and keep it
safe for future reference. It is essential to know the information
and comply with the instructions given in this manual to ensure
the fitting is installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting
or to other property or persons deriving from installation, use and
maintenance that have not been carried out in conformity with this
instruction manual, which must always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the
characteristics stated in this instruction manual at any time and
without prior notice.
1
1
C61325

Advertisement

loading
Need help?

Need help?

Do you have a question about the ALPHA SPOT HPE 1500 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Clay Paky ALPHA SPOT HPE 1500

Summary of Contents for Clay Paky ALPHA SPOT HPE 1500

  • Page 1 Control panel the fitting is installed, used and serviced correctly and safely. CLAY PAKY S.p.A. disclaims all liability for damage to the fitting Menu setting or to other property or persons deriving from installation, use and...

  • Page 2: Safety Information

    SAFETY INFORMATION • Installation Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of anchorage is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible.
  • Page 3 UNPACKING AND PREPARATION Lamp 1500W (fitted into projector) 099105 2 x 183102/802 Packing contents - Fig. 1 UNLOCKED LOCKED LOCKED UNLOCKED PAN Mechanism Lock and Release every 90°) - Fig. 2 TILT Mechanism Lock and Release every 45°) - Fig. 3 ALPHA SPOT HPE 15...
  • Page 4 INSTALLATION AND START-UP Installing the projector - Fig. 4 The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall. WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request). This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.

  • Page 5: Control Panel

    CONTROL PANEL Mains Connecting to the mains supply - Fig. 6 DMX 512 5 PIN SCREEN SIGNAL SIGNAL DMX 512 DMX 512 3 PIN SIGNAL SCREEN SIGNAL Connecting to the control signal line DMX) - Fig. 7 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified.
  • Page 6 Reversal of the display - Fig. 9 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Setting the projector starting address On each projector, the starting address must be set for the control signal (addresses from 1 to 512).

  • Page 7: Main Menu

    MENU SETTING MAIN MENU System Set Up Option Lamp Dmx Information Address Errors Invert Pan / Tilt Channel Fixture Mode Hours Invert Tilt Lamp Ethernet Hours Swap Pan-Tilt Lamp Fixture ID Strikes Encoder Pan-Tilt System Color Option Color Version Mixing Fixed Wheel Board Information...
  • Page 8 SET UP MENU DMX ADDRESS NOTE: without the DMX signal the Address XXX) flashing Set Up Address xxx Allows you to select the DMX ADDRESS Address 1) Press - the current DMX Adress appear on the display. 2) Use the UP , DOWN , RIGHT keys to plan the DMX...
  • Page 9 Swap Pan-Tilt Used for swapping Pan and Tilt channels (as well as Pan fine and Tilt fine). Swap Pan-Tilt 1) Press - the current settings appear on the display (On or Off). 2) Use the UP and DOWN keys to enable (On) or disable (Off) Pan and Tilt channel swap.

  • Page 10: Information Menu

    DISPLAY Display Used for automatically reduce brightness on the display after about 30 seconds in idle. 1) Press - the current settings appear on the display (On or Off). 2) Use the UP and DOWN keys to enable (On) or disable (Off) the decreasing of display brightness.
  • Page 11 3) Select YES to reset partial projectors counter or NO to keep the current setting and return to the top menu level. LAMP HOURS Total Lamp Used for displaying the lamp working hours (total and partial). Partial XXX Hours Reset... 1) Press - Hours total and partial appears on the display.

  • Page 12: Test Menu

    FANS MONITOR Fans Speed (RPM) Monitor Pwr.Sup XXXX Used for displaying the speed of each fan installed in the projector: Ball.In. XXXX Pwr.Sup (Power supply Fan) Ball.Out XXXX Eff.In XXXX Ball. IN (Ballast IN Fan) Eff.Out XXXX Ball. Out (Ballast OUT Fan) Iris XXXX Eff.IN (Effects IN Fan)
  • Page 13 ADVANCED MENU To enable the Advanced Menu set up the Access code (1234) using the Code Advanced , DOWN , RIGHT keys. 1234 Press - Menu advanced appears on the display UP LOAD FIRMWARE Transfer the firmware on all Allows you to transfer the firmware from 1 fixture to all the connected fixtures. the connected fixtures ? Upload Are you sure ?
  • Page 14 MAINTENANCE 1/4 Turn 1/4 Turn Locking and releasing Pan and Tilt movements - Refer to the instructions in the UNPACKING AND PREPARATION section. Opening the head covers - Fig. 11. Closing the head covers - Fig. 12. ALPHA SPOT HPE 15...
  • Page 15 Lamp change - Fig 14 Take the new lamp out of its package and insert in the fitting. WARNING: do not touch the lamp s envelope with bare hands. Should this happen, clean the bulb with a cloth soaked in alcohol and dry it with a clean, dry cloth.
  • Page 16 Upper Side Fan support plate opening and closing Upper side) - Fig. 17 Lower Side 085908/001 085907/001 085904/001 085903/001 085912/001 085911/001 085906/001 085901/001 Replacing fixed gobos ø 31.5 mm - max 25 mm image - thickness max 1 mm) - Fig. 18 ALPHA SPOT HPE 15...
  • Page 17 084627/001 Replacing rotating gobos ø 37.4 mm - max 25 mm image – thickness 1 mm) - Fig. 20 IMPORTANT: Use only glass gobos on the rotating gobos wheels. For any further information contact CLAY PAKY. Continue ALPHA SPOT HPE 15...
  • Page 18 • General cleaning of internal parts. • Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Clay Paky. • General visual check of the internal components, cabling, mechanical parts, etc.
  • Page 19 Extraction of the effect modules: Preliminary operations - Fig. 23 Continue ALPHA SPOT HPE 15...
  • Page 20 Upper Side Lower Side Upper Side Upper Side Extraction of the effect modules - Fig. 24 IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 24 and 25 in reverse order ALPHA SPOT HPE 15...
  • Page 21 Upper Side Upper Side Upper Side Upper Side Extraction of the effect modules - Fig. 25 IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged. Insertion of the effect modules: Repeat the operations indicated in Fig. 24 and 25 in reverse order ALPHA SPOT HPE 15...

  • Page 22: Technical Information

    TECHNICAL INFORMATION Power supplies available IP20 protection rating 200-240V 50/60Hz • Protected against the entry of solid bodies larger than 12mm (0.47”). Input power • No protection against the entry of liquids. • 2000VA a 230V 50Hz. CE Marking Lamp In conformity with the European Union Low Voltage Discharge lamp.
  • Page 23 CHANNEL FUNCTION ALPHA SPOT HPE 1500 CHANNEL MODE CHANNEL STANDARD VECTOR CYAN CYAN MAGENTA MAGENTA YELLOW YELLOW C.T.O C.T.O COLOUR WHEEL COLOUR WHEEL MACRO COLOURS MACRO COLOURS STOP/STROBE STOP/STROBE DIMMER DIMMER DIMMER FINE DIMMER FINE IRIS IRIS ANIMATED STAR GOBO...
  • Page 24 • MACRO COLOURS - channel 6 • COLOUR MIXING - channel 1 - 2 - 3 Operation with option color mixing: RGB EFFECT CHANNEL 1 CHANNEL 2 CHANNEL 3 COLOUR EXCLUDED COLOUR INSERTED CYAN MAGENTA YELLOW IMPORTANT: The lamp dim to half power 1 second after all the 3 channels stay at 0% level.
  • Page 25 • IRIS - channel 10 • ROTATING GOBO 1 CHANGE - channel 13 EFFECT GOBO 6 SHAKE, FAST SPEED 92.0 GOBO 6 SHAKE, SLOW SPEED 91.7 GOBO 5 SHAKE, FAST SPEED 84.0 GOBO 5 SHAKE, SLOW SPEED 83.7 GOBO 4 SHAKE, FAST SPEED 75.5 GOBO 4 SHAKE, SLOW SPEED 75.0...
  • Page 26 • ROTATING GOBO 2 CHANGE - channel 16 • ANIMATION DISK INSERTION - channel 19 EFFECT GOBO 6 SHAKE, FAST SPEED EFFECT DISK INSERTED 92.0 GOBO 6 SHAKE, SLOW SPEED 91.7 GOBO 5 SHAKE, FAST SPEED 84.0 GOBO 5 SHAKE, SLOW SPEED 83.7 GOBO 4 SHAKE, FAST SPEED 75.5...
  • Page 27 • FROST - channel 23 • AUTOFOCUS DISTANCE - channel 27 EFFECT EFFECT FROST INSERTED 100 METRES 50.0 50 METRES 40.0 40 METRES 30.0 30 METRES 20.0 20 METRES 10.0 10 METRES FROST EXCLUDED 5 METRES 0.0-3.0 AUTOFOCUS OFF • FOCUS - channel 24 •...
  • Page 28 • PAN - channel 30 • TILT - channel 32 Operation with option InvertPan Operation with option Invert Tilt (Tilt conventionally represented at 14% and option Invert Tilt Off) (Pan conventionally represented at 0% and option Invert Pan Off) 50.0 Operation with option InvertPan Operation with option Invert Tilt (Tilt conventionally represented at 14% and option Invert Tilt...
  • Page 29 10.0 EFFECTS RESET UNUSED RANGE • LAMP CONTROL only with option LAMP DMX On) - channel: 36 IMPORTANT: Alpha Spot HPE 1500 is not provided with hot restrike igniter EFFECT LAMP ON (1500 W) Lamp ignition after 5 s in full power levels.
  • Page 30 TIMING CHANNELS Timing Channel Channel function Pan - Tilt time Pan – Tilt – Pan Fine – Tilt Fine Colour time Cyan - Magenta - Yellow – C.T.O. – Color wheel Beam time Dimmer - Iris -Focus effects movment - Focus - Zoom - Frost – Rotating Prism change – Frost insertion Gobo time Gobo Fix - Rotating Gobo 1/2 change –...
  • Page 32 CLAY PAKY - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.it S.p.A.