ADJ Inno Pocket Spot LZR User Instructions page 9

Inno Pocket Spot LZR
2. "Sh X" will now be displayed, "X" representing a number between
0-4. Shows 1-4 are factory programs, while show "0" is random mode.
Use the UP or DOWN buttons to find your desired show.
3. When you have found your desired show press ENTER, then press
and hold the MENU button for at least 3 seconds to activate. After
you have set your desired show, it can be changed at any time using
the UP or DOWN buttons.
SOUN -
Sound Active mode.
1. Press the MENU button until "SOUN" is displayed, press ENTER.
2. The display will show either "ON" or "OFF". Press the UP or
DOWN buttons to select "ON" to activate sound active mode, or
"OFF" to deactivate sound active mode.
3. Press ENTER to confirm.
SENS -
In this mode you can adjust the sound sensitiv-
ity.
1. Press the MENU button until "SENS" is displayed, press ENTER.
2. A number between 0-100 will be displayed. Press the UP or DOWN
buttons to adjust the sound sensitivity. 0 being the least sensitive,
and 100 being the most sensitive.
3. When you have found your desired setting press ENTER to confirm.
DNST
- This mode can be used as a precaution mode,
that in case the DMX signal is lost, interrupted, or power is
lost, the operating mode chosen in the setup is the running
mode the fixture will go into when the DMX signal is lost. You
can also set this as the operating mode you would like the
unit to return to when power is applied.
1. Press the MENU button until "DNST" is displayed, and either
"MASL", "BLND", or "LAST" will be displayed beneath.
2. Press ENTER and the bottom choice will begin to flash. Use the UP
or DOWN buttons to choose an operating mode you would like the unit
ADJ Products, LLC - www.adj.com - Inno Pocket Spot LZR Instruction Manual Page 16
System Menu Inno Pocket Spot LZR
to start up in when power is applied or the DMX signal is lost.
• LAST - If the DMX signal is lost the fixture will stay in the last DMX
setting. If power is applied and this mode is set, the unit will automati-
cally go into the last DMX set up.
• MASL (Master Slave) - If the DMX signal is lost or power is applied,
the unit will automatically go into Master Slave mode and run a built-in
show.
• BLND (Blackout) - If the DMX signal is lost or interrupted, the unit will
automatically go into stand by mode.
3. Press ENTER to confirm your desired set up.
DIND -
1. Press the either the MENU button until "DIND" is displayed, press
ENTER. 1 of 5 dimmer curves will be displayed. "STDA" (standard),
"STGE" (stage), "TV" (TV), "ARAL" (theatrical), or "THAL" (Architec-
tural).
2. Press the UP or DOWN buttons to find your desired dimmer curve
and press ENTER to confim and exit.
PINT
1. Press the MENU button until "PINT" is displayed, press ENTER.
Either "Yes" or "No" will be displayed.
2. To activate the Pan inversion press the UP or DOWN buttons until
"Yes" is displayed, press ENTER to confim. To deactivate Pan inver-
sion, select "No" and press Enter.
TINT
1. Press the MENU button until "TINT" is displayed, press ENTER.
Either "Yes" or "No" will be displayed.
2. To activate the tilt inversion press the UP or DOWN buttons until
"Yes" is displayed, press ENTER to confim. To deactivate tilt inver-
sion, select "No" and press Enter.
ADJ Products, LLC - www.adj.com - Inno Pocket Spot LZR Instruction Manual Page 17
This will let select your desired dimmer curve.
- Pan Inversion
- Tilt Inversion
System Menu