Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Biomega BOS
Summary of Contents for Biomega BOS
- Page 1 MANUAL...
-
Page 2: Table Of Contents
INDEX The manual Get started 05/06 How to mount front wheel 07/08 Handlebar Stem and headset 10/11 Pedals Brakes 12/13 Gearhubs 14/16 Wheels Gates Belt Drive 17/18 BOS specifics 19/25... -
Page 3: The Manual
Furniture for locomotion General bike safety practices: Congratulations on the purchase of your new Biomega bike. 1. Always follow the traffic laws in your country. This manual will assist you in setting up and maintaining your bike. Read it through 2. -
Page 4: Get Started
GET STARTED With your new biomega bike ADJUSTMENTS BEFORE YOUR FIRST RIDE Before taking your new bike on your first ride, it is important for your own comfort and for your safety that you adjust your bike. SADDLE In order to fit your bike to your size and taste, please follow these instructions: Adjust the seat height by loosening the seat clamp bolt by using a 5mm Allen key. -
Page 5: How To Mount Front Wheel
the axle; first put the supplied washer (4 d) outside the fork and then the hub nut (4 e) outside the washer. The hub nut is then tightened firmly with an 8mm allen key. HOW TO MOUNT FRONT WHEEL P. 4 1. -
Page 6: Handlebar
Loosen the four bolts on the front of the stem, and tilt the bar forward or backwards. When you have found a suitable position, To align the Biomega stem with the front wheel, loosen the stem clamp bolt situated on the side of the stem with a 5mm Allen key, align the stem with retighten the bolts. -
Page 7: Pedals
BRAKES Biomega bikes are equipped with quality Shimano hydraulic disc brakes. We recommend you study the Shimano disc brake manual found inside the box with your bike. WARNING: Always check your brakes before you ride your bike. Ensure that they are working properly. Failing to do so may result in injury and serious damage. -
Page 8: Gearhubs
For more information about maintaining the hub or how to connect the hub with the shifter, please see the attached hub manual or visit www.shimano.com. The lever is adjusted in relation to the handlebar by loosening the lever clamp bolt close to the handlebar. Biomega recommends you set the break levers at a 45°angle downwards. -
Page 9: Wheels
IMPORTANT: Before you ride, check: Is gear shifting happening smoothly? Is there any noticeable damage to the electric wires? Are there any unusual between two gears. This means that the pawl of the lower gear is still available in case the higher gear is not engaging yet. The clicking noise IS NOT a sign that something is wrong on your internal hub. -
Page 10: Gates Belt Drive
CARE FOR YOUR CARBON DRIVE GATES BELT DRIVE • Impervious to sunlight. Biomega bikes are equipped with a high quality belt drive to minimize maintenance and increase comfort. • Wash with water. IMPORTANT: Find general safety information below. Also read enclosed Gates manual. -
Page 11: Bos Specifics
BOS SPECIFICS The BOS/Boston bicycle is designed with a special DT-wire lock system. Therefore this bike needs comprehensive explanations. DT-wire Tension DT-wire is factory adjusted. A correctly adjusted DT-wire ensures that the bike can be locked/unlocked and that the bike frame is stable while riding. - Page 12 DT-WIRE TENSION GEAR CABLES/WIRES DT-wire is factory adjusted. A correctly adjusted DT-wire ensures that the bike can be locked/unlocked and that the bike frame is stable while riding. The DT-wire should never be too tight or too loose. If for any reason the cable adjustment has been modified, follow the manual directions to ensure Lubricate with a Teflon spray every six months.
- Page 13 Check your tubes for any leaks. If your tire is flat, there is most likely a hole in the tube. Patch the leak with a patch kit. If problem persists, change the tube. Never ride a bike with a flat tire. FOR BOS/BOSTON AND NYC/NEW YORK 26” BIKE TIRES In order to maintain Shimano gear hub performance, it is recommended that you contact a bicycle mechanic to carry out maintenance such as greasing the internal parts about once every two years from the first time of use (once about every 5,000 km if the bicycle is used very frequently).
- Page 14 BOTTOM BRACKET Subject to the following limitations, terms and conditions, Biomega war- rants to the original owner of each new Biomega bike that this bike is free of defective materials and workmanship for a period of 2 (two) years from the date of the original purchase from an authorized Biomega dealer.
- Page 15 BIOMEGA Hagemannsvej 17 8600 Silkeborg Denmark WWW.BIOMEGA:COM...