Operation And Adjustment; How To Fold And Move The Treadmill - ProForm 525 SI User Manual

Change the incline of the treadmill, if desired.
6
To change the incline
of the treadmill, hold
down the top or bottom
of the incline button.
Important: Do not
change the incline of
the treadmill by plac-
ing objects under the
treadmill. Change the
incline only as
described above.
When you are finished exercising, stop the
7
walking belt and remove the key.
Step onto the foot rails,
stop the walking belt,
and remove the key
from the console. Store
the key in a secure
place. After the key is
removed, the displays
will remain on for
about five minutes.
Note: Any time that the walking belt is stopped
and no console buttons are pressed for five min-
utes, the displays will automatically turn off in
order to conserve the batteries.
HOW TO SELECT KILOMETERS AND MILES
The console can display distance and speed in either
kilometers or miles. The letters ÒKPHÓ or ÒMPHÓ will

HOW TO FOLD AND MOVE THE TREADMILL

HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, unplug the power cord. Caution:
You must be able to safely lift 45 lbs (20 kg) in order to
raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
vertical position.
10
appear in the SPEED display to show which unit of
measurement is selected.
To change
Console
the unit of
Screws
measure-
ment, first
UNPLUG
THE POWER
CORD. Next,
remove the
six screws
attaching the
console to
the console
Screws
base. Lift the
Console Base
console a few
inches, being
careful not to
pull on the
wires, and
turn the con-
sole over.
Locate the
Switch
small switch
on the back
of the con-
sole. Move
the switch to
the opposite
side to change the unit of measurement. Reattach the
console to the console base. After changing the unit
of measurement, remove one of the batteries from
the console for about five seconds and then reinsert
it. This will reset the console.
8. Remove the backing from the Adhesive Clip (77). Press
the Adhesive Clip onto the Rear Roller Endcap (78) in the
indicated location. Press the Allen Wrench (76) into the
Adhesive Clip.
9. Make sure that all parts are tightened before you use the treadmill. To protect the floor or carpet, place a
mat under the treadmill. For information on ordering a mat, see ORDERING REPLACEMENT PARTS on the
back cover.

OPERATION AND ADJUSTMENT

THE PERFORMANT LUBE TM WALKING BELT
Your treadmill features a walking belt coated with PERFORMANT LUBE
TANT: Never apply silicone spray or other substances to the walking belt or the walking platform. They will
deteriorate the walking belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
This product must be earthed. If it should malfunction or break
down, earthing provides a path of least resistance for electric
current to reduce the risk of electric shock. This product is
equipped with a cord having an equipment-earthing conductor
and a earthing plug. Plug one end of the cord into the treadmill.
Plug the power cord into an appropriate outlet that is prop-
erly installed and earthed in accordance with all local codes
and ordinances.
DANGER:
Improper connection of the
equipment-earthing conductor can result in an in-
creased risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to
whether the product is properly earthed. Do not mod-
ify the plug provided with the productÑif it will not fit
the outlet, have a proper outlet installed by a qualified
electrician.
Use only a power cord type H05VV-F with a conductor of at least 1mm
appliance coupler.
8
77
78
76
TM , a high-performance lubricant. IMPOR-
2 , with a country recognised plug and an
7