Related Manuals for Megasat SAT IP Server 2
Summary of Contents for Megasat SAT IP Server 2
- Page 1 SAT>IP Server 2 user manual Stand: 1.0 November 2014 // Technical changes, misprints and errors reserved. Megasat Werke GmbH | Industriestraße 4a | D-97618 Niederlauer | www.megasat.tv | info@megasat.tv...
-
Page 2: Table Of Contents
Content Safety Instructions Please read the manual thoroughly before operating the equipment. In case of incorrect Safety Instructions...................... 03 or improper handling, the warranty becomes void. 1. Introduction ......................04 Power supply: Before start please check the correct operation voltage of the 2. -
Page 3: Introduction
1. Introduction 2. Connection & How to access SAT>IP Server 2 allows free satellite live TV/Radio programs to be received & distributed to SAT>IP Client compliant devices like smart phones, tablet pc‘s and notebook pc‘s & other client devices over Wired/Wireless home network in both unicast/multicast mode of transmission. - Page 4 2. Connection & How to access Identify the IP address • Select in the list of „UPnP Devices“ to „Megasat SAT> IP Server 2“, and read the corre- Turn on the server. The server connects to the network and receives sponding „Base URL“...
-
Page 5: Login / Logout
3. Login / Logout 4. System Settings Login Server box supports the below network mode of interfaces. • Wired Network Once the browser was successful- • Wireless Network ly connected to Server, then the „Login“ page will be displayed. The default user name for server is „admin“... -
Page 6: Network Settings
4. System Settings 4. System Settings Click „System Setting“ from the Server page. 4.1.1 Wired Topics covered under Admin are listed below: • Network Settings By default the Server box is in DHCP mode. • LNB Settings • Import Settings Server acquires IP address from DHCP server &... -
Page 7: Wireless
4. System Settings 4. System Settings Password request screen will be 4.1.2 Wireless displayed if user select WPA se- cure system available WiFi router. Using keypad user should enter Wireless option can be configure the valid WPA key. by Auto (or) Manual. A warning pop-up is displayed if the password is invalid or the Receiver is unable to connect to... -
Page 8: Lnb Settings
4. System Settings 4. System Settings The Green color tick icon is dis- 4.2 LNB Settings played if WiFi Router is connec- ted without any problem. All WiFi Select the type of LNB that is connected to Satellite input of your box based on your network settings are stored in the satellite installation. - Page 9 4. System Settings 4. System Settings 4.2.1 LNB Settings 4.2.2 Quad To configure the below settings from the LNB settings menu. Satellite reception system consists of a Quad LNB. Connect the 4 outputs of the LNB to the inputs 1... 4 of the Server box via suitable SAT antenna cables. •...
-
Page 10: Quattro
4. System Settings 4. System Settings 4.2.3 Quattro 4.2.4 Unicable Satellite reception system consists of a Quattro LNB. Connect the 4 outputs of the Unicable distribution is a satellite TV technology that enables delivery of broadcast pro- Quattro LNB to the inputs 1... 4 of the Server via suitable SAT antenna cables & and ensu- gramming to multiple users over a single coaxial cable. -
Page 11: Jess
4. System Settings 4. System Settings 4.2.5 Jess 4.2.6 DiSEqC 32 users can able to view the 8 different satellites via user band frequency. DiSEqC 1.2 is used to move the motor manually. Using this option user can move the motor with the following moving controls. - Page 12 4. System Settings 4. System Settings Set the Dish moving type as INSTALLER. Press Left/Right key in Drive East/West option Set the Dish moving type as USER. Press Left/Right key in Drive East/West option to to move the motor. Now motor will be move continuously[coarse movement]. Motor move the motor.
- Page 13 4. System Settings 4. System Settings The above picture which shows the Advanced setup, through this setup user can per- form the below listed Motor related settings, • Enable / Disable limit - Enable or Disable the motor rotation to the restricted direc- tion angle.
-
Page 14: Usals
4. System Settings 4. System Settings 4.2.7 USALS The above picture shows the Motor moving in-progress. USALS means Universal Satellite Automatic Location System. This type is used to move the dish towards the satellite position automatically. USALS is used to position the dish automatically without user stress. By giving the input of satellite angle, user latitude &... -
Page 15: Import Settings
4. System Settings 4. System Settings 4.3 Import Settings 4.4 Export Settings Import Settings: User can import the configuration information which was available Using export settings user can retrieve the user configured details of the Server & stored from the receiver (can be extracted using export settings). it as separate XML file. -
Page 16: System Status
5. System Status 6. Tuner System status menu gives the informations about: Select the type of Tuner of your box based on your satellite installation. Topics covered under are listed below: • Tuner details • Tuner parameters Tuner Settings • Streaming details •... - Page 17 6. Tuner 6. Tuner 6.1 Tuner Settings • By default the Server box is in Dynamic mode. • Server box tuned the client requested carrier in Dynamic mode. Select „Static“ for configure the tuner to the particular frequency where the client can only tune that carrier.
-
Page 18: Software Update
6. Tuner 7. Software Update In order to support S/W upgrading, we have supported the below upgrading modes, 6.2 Tuner Test • S/W download via USB • S/W download via OND • S/W download via WEB UI 7.1 USB Enter the below valid parameters to check the tuner lock sattus. The S/W Upgrade via USB option used to download the latest software by USB memory •... - Page 19 7. Software Update 7. Software Update If USB media is inserted with S/W image and when user select „Software Upgrade via System switch to Upgrader mode when select Yes from the confirmation. USB“ then above message will be displayed. ENGLISH ENGLISH...
- Page 20 7. Software Update 7. Software Update System boot the upgrader mode and if the „Update“ folder in USB contains more than Select the correct image and press the ok key, downloading will start. one file the above screen will be displayed. User need to select the correct image. Other- wise it directly start the S/W fusing.
- Page 21 7. Software Update 7. Software Update The above slide indicated downloading in-progres. After complete the downloading, box booted with new S/W. Warning - Don‘t power off the STB during software downloading/erasing/fusing. ENGLISH ENGLISH...
-
Page 22: Ond
7. Software Update 7. Software Update 7.2 OND Upgrade the software from anywhere in the network world through TCP/IP mode of When select „Search“ Button, STB will search new S/W in the Network. connection in a secure manner. Select the Network Interface mode and enter the OND server IP address for search the S/W availability. - Page 23 7. Software Update 7. Software Update If new S/W is not available then STB shows the above message. If new S/W is available then STB shows the above confirmation message. ENGLISH ENGLISH...
- Page 24 7. Software Update 7. Software Update Once user press OK STB starts to connect the server. Once successfully connected with After complete the downloading, box booted with new S/W. server then downloading will be started. ENGLISH ENGLISH...
-
Page 25: Webui
7. Software Update 7. Software Update 7.3 WebUI User can able to cancel the upgrade mode with confirmation via press the cancel button. This is simple file based upgrading process by this user can able to upgrade the s/w image from the local PC or from USB device connected to the PC. The s/w image should be of format .nig ENGLISH ENGLISH... -
Page 26: Admin
7. Software Update 8. Admin Server box supports S/W version display and Password setup mechanism to change the server configuration. • S/W Version • Change Password 8.1 SW Version The Version menu displays below informations about the application. • Serial Mumber •... - Page 27 9. Specifications Notes • Processor ............STi7108 • Flash ..............1 MB NOR / 128 MB NAND • RAM ..............512 MB / DDR3-1066 • Ethernet ............RJ45 10/100/1000 • Specification ..........SAT>IP 1.2 compatible • Video / Audio Unterstützung ... MPEG2 / MPEG4 / TS & PS •...
- Page 28 Status: 1.0 November 2014 // Technical changes, misprints and errors reserved. Megasat Werke GmbH | Industriestraße 4a | D-97618 Niederlauer | www.megasat.tv | info@megasat.tv...