Page 1
3 7 63 1515 0 SERVICE MANUAL CD RECEIVER 49858 2003 KD-S845 KD-S845 45Wx4 TU NER L 13942296513 Area Suffix U ------- Other Areas TABLE OF CONTENTS Important Safety Precautions ............. 2 Disassembly method .
http://www.xiaoyu163.com 3 7 63 1515 0 SECTION 1 Important Safety Precautions Safety Precautions Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
http://www.xiaoyu163.com 3 7 63 1515 0 Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.2.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as DVD players.
Page 4
http://www.xiaoyu163.com 3 7 63 1515 0 SECTION 2 Disassembly method Main body 2.1.1 Removing the front panel assembly (See Fig.1) (1) Push the detach button in the lower left part of the front panel and remove the front panel assembly in the direction of the arrow.
Page 5
http://www.xiaoyu163.com 3 7 63 1515 0 2.1.3 Removing the heat sink (See Fig.4) (1) Remove the three screws A on the left side of the main body. Heat sink Fig.4 2.1.4 Removing the bottom cover (See Figs.5 and 6) • Prior to performing the following procedure, remove the front Joint d panel assembly, front chassis assembly and heat sink.
Page 6
http://www.xiaoyu163.com 3 7 63 1515 0 2.1.5 Removing the rear bracket (See Fig.7) • Prior to performing the following procedure, remove the front panel assembly, front chassis assembly, heat sink and bottom Rear bracket cover. (1) Remove the one screws B, for screws C and three screws D on the back side of the main body.
Page 7
http://www.xiaoyu163.com 3 7 63 1515 0 2.1.8 Removing the front board (See Figs. 10 to 12) • Prior to performing the following procedure, remove the front panel assembly. (1) Remove the four screws G on the back side of the front panel assembly.
Page 8
http://www.xiaoyu163.com 3 7 63 1515 0 CD mechanism section 2.2.1 Removing the CD mechanism control board (See Fig.1 and 2) (1) Unsolder the part a and b on the CD mechanism control board. Damper bracket CD mechanism assembly (2) Remove the stator fixing the CD mechanism control board and the damper bracket (To remove the stator smoothly, pick up the center part).
Page 9
http://www.xiaoyu163.com 3 7 63 1515 0 2.2.2 Removing the loading motor (See Fig.3 to 5) • Rrior to performing the following procedure, remove the CD mechanism control board. CD mechanism control board (1) Remove the two springs f attaching the CD mechanism as- sembly and the front bracket.
Page 10
http://www.xiaoyu163.com 3 7 63 1515 0 2.2.3 Removing the CD mechanism assembly (See Fig.1, 6 to 9) • Prior to performing the following procedure, remove the CD mechanism control board and the front bracket (loading mo- assembly CD mechanism Damper bracket tor).
Page 11
http://www.xiaoyu163.com 3 7 63 1515 0 2.2.4 Removing the feed motor assembly (See Fig.10) • Prior to performing the following procedure, remove the CD mechanism control board, the front bracket (loading motor) FD screw Part i Feed motor assembly and the CD mechanism assembly. (1) Remove the two screws F and the feed motor assembly.
Page 12
6. Digital tester FM 87.5MHz to 108.0MHz AM 531 kHz to 1602 kHz 7. Tracking offset meter 8. Test Disc JVC :CTS-1000 9. Extension cable for check EXTGS004-26P 1 Dummy load Exclusive dummy load should be used for AM, and FM. For FM dummy load, there is a loss of 6dB between SSG output and antenna input.
Page 13
http://www.xiaoyu163.com 3 7 63 1515 0 Flow of functional operation unit TOC read Power ON Set Function CD When the laser diode correctly When the pickup correctly moves emits to the inner area of the disc Microprocessor $82 $81 Disc inserted Microprocessor commands commands...
Page 14
http://www.xiaoyu163.com 3 7 63 1515 0 3.2.1 Feed section Is 3.3V present at IC501 Is the voltage output at Is the wiring for IC541 pin "20"? IC541 pin "40" 5V or 0V? pin 27? Check CD 8V Check the vicinity of and 5V.
Page 15
http://www.xiaoyu163.com 3 7 63 1515 0 Maintenance of laser pickup 3.4 Replacement of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens Turn off the power switch and,disconnect the with a alcohol soaked cotton swab.
http://www.xiaoyu163.com 3 7 63 1515 0 LA4743K (IC301) : Power amp. • Block diagram 2200 F 0.022 F Vcc 1/2 Vcc 3/4 IN 1 OUT 1+ 0.22 F OUT 1- PWR GND1 Protective circuit OUT 2+ IN 2 OUT 2- 0.22 F PWR GND2 L 13942296513...
Page 19
http://www.xiaoyu163.com 3 7 63 1515 0 • Pin layout • Pin function Pin No. Symbol Function Pin No. Symbol Function Header of IC FLIN Front Lch input Power GND RLIN Rear Lch input Outpur(-) for front Rch ONTIME Power on time control STDBY Stand by input Output (+) for rear Lch...
Page 27
http://www.xiaoyu163.com 3 7 63 1515 0 • Pin function Symbol Function Bit clock outputpin 32fs, 48fs, or 64fs selectable by command. LRCK L/R channel clock output pin."L" for L channe and "H" for R channel. Output polarity can be inverted by command.
Page 28
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol Function RFGC RF amplitude adjustment control signal output pin. TEBC Tracking balance control signal output pin. APC circuit ON/OFF signal output pin. At laser on, high impedance with UHS="L", H output with UHS="H". AVDD3 Analog 3.3V power supply voltage pin.
Page 29
http://www.xiaoyu163.com 3 7 63 1515 0 4.14 TEA6320T-X (IC161) : E.volume • Pin layout OUTLR OUTRR OUTRF OUTLF Vref MUTE CD-CH TAPE TUNER • Block diagram VOLUME 2 MUTE 0 to 55 dB FUNCTION BALANCE ZERO CROSS FENDER REAR POWER DETECTOR SUPPLY VOLUME 1...
Page 31
http://www.xiaoyu163.com 3 7 63 1515 0 • Pin function Pin No. Symbol I/O Description Pin No. Symbol I/O Description Digital GND /RESET Hard reset input terminal(H:Normal I/O External SRAM data input/output 2 operation L: Reset) terminal MiMD Micon I/F mode select input terminal I/O External SRAM data input/output 3 O External SRAM address output 0 terminal terminal...
Page 32
http://www.xiaoyu163.com 3 7 63 1515 0 4.16 UPD784215AGC184 (IC701) : CPU • Pin layout • Pin function Pin No. Symbol Function CD mechanism detect switch CD mechanism detect switch CD mechanism detect switch REST Reset signal input terminal from CD mechanism Loading motor control signal input terminal Loading motor control signal input terminal Not use...
Page 33
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Symbol Function BUSSCK J-BUS serial clock signal I/O terminal BUSI/O J-BUS data input/output terminal LCDDA Data output terminal for LCD driver LCDCK Clock output terminal for LCD driver LCDCE Chip enable 1 output terminal for LCD driver 44 to 52 Not use SD/ST...
Page 34
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY MOBILE ENTERTAINMENT CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.49858) Printed in Japan http://www.xiaoyu163.com...
KD-S845 3 7 63 1515 0 SCHEMATIC DIAGRAMS CD RECEIVER KD-S845 CD-ROM No.SML200305 Area suffix U --------------- Other Areas KD-S845 45Wx4 L 13942296513 TU NER Contents Block diagram Standard schematic diagrams Printed circuit boards 2-5~7 u163 No.49858SCH COPYRIGHT 2003 VICTOR COMPANY OF JAPAN, LTD.
KD-S845 3 7 63 1515 0 Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 44
KD-S845 3 7 63 1515 0 L 13942296513 u163 V ICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY 10-1,1Chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.49858SCH) 2003/05 http://www.xiaoyu163.com...
KD-S845 3 7 63 1515 0 PARTS LIST [ KD-S845 ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix U --------------------- Other Areas L 13942296513 - Contents - Exploded view of general assembly and parts list (Block No.M1) CD mechanism assembly and parts list (Block No.MB)
Page 46
KD-S845 3 7 63 1515 0 Exploded view of general assembly and parts list Block No. L 13942296513 u163 http://www.xiaoyu163.com...
Page 47
KD-S845 3 7 63 1515 0 General assembly Block No. [M][1][M][M] Symbol No. Part No. Part Name Description Local ------------ CD MECHA FSJC1029-401 TOP CHASSIS FSMH3001-202 SIDE PANEL FSKM3011-002 BOTTOM COVER FSMA3004-203 INSULATOR QYSDST2604Z SCREW 2.6mm x 4mm(x3)
Page 48
KD-S845 3 7 63 1515 0 CD mechanism assembly and parts list Block No. Grease G-31SA TN-CCD1001Z-138S G-31SA(Bottom side) RX-405 L 13942296513 u163 106 29 http://www.xiaoyu163.com...
Page 49
KD-S845 3 7 63 1515 0 CD mechanism Symbol No. Block No. [M][B][M][M] Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local 303105310T FEED MO ASSY 303105311T SPINDLE MO ASSY 303105312T FEED SCREW ASSY...
KD-S845 3 7 63 1515 0 Electrical parts list Main board Block No. [0][1][0][0] Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local D972 RB160M-30-X SB DIODE D981 1SS355-X SI DIODE...
Page 51
KD-S845 3 7 63 1515 0 Symbol No. Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local C316 QERF1EM-475Z E CAPACITOR 4.7uF 25V M C558 NCB31EK-473X C CAPACITOR 0.047uF 25V K C317...
Page 52
KD-S845 3 7 63 1515 0 Symbol No. Symbol No. Part No. Part Name Description Local Part No. Part Name Description Local NRSA63J-470X MG RESISTOR 47Ω 1/16W J R506 NRSA63J-822X MG RESISTOR 8.2kΩ 1/16W J NRSA63J-103X MG RESISTOR 10kΩ...
Page 53
KD-S845 3 7 63 1515 0 Front board Symbol No. Part No. Part Name Description Local Block No. [0][2][0][0] R723 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J Symbol No. R725 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J Part No.
Page 54
KD-S845 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local R649 NRSA63J-821X MG RESISTOR 820Ω 1/16W J R651 NRSA63J-222X MG RESISTOR 2.2kΩ 1/16W J R652 NRSA63J-222X MG RESISTOR 2.2kΩ 1/16W J R653 NRSA63J-103X MG RESISTOR 10kΩ...
Page 56
KD-S845 3 7 63 1515 0 Packing materials and accessories parts list Block No. A2 A3 L 13942296513 A4A5A6 A7A8 u163 3-12 http://www.xiaoyu163.com...
Page 57
KD-S845 3 7 63 1515 0 Packing and accessories Block No. [M][3][M][M] Symbol No. Part No. Part Name Description Local GET0163-001A INST BOOK ENG CHI CHI(TAIWAN)ARA GET0163-002A INSTALL MANUAL ENG CHI CHI(TAIWAN)ARA LVT0918-001A MP3 SHEET VKZ4027-202 PLUG NUT...
Need help?
Do you have a question about the KD-S845 and is the answer not in the manual?
Questions and answers