Nominal Data; Data According To Erp Directive; Technical Description - ebm-papst A3G710-AO81-03 Operating Instructions Manual

A3G710-AO81-03

3.2 Nominal data

Motor M3G112-IA
Phase 3~
Nominal voltage / VAC 400
Nominal voltage 380 .. 480
range / VAC
Frequency / Hz
50/60
Method of obtaining ml
data
-1
Speed / min 900
Power consumption / W 930
Current draw / A
1.5
Max. back pressure / Pa 125
Min. ambient -25
temperature / °C
Max. ambient 60
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change

3.3 Data according to ErP Directive

01 Overall efficiency η / %
es
02 Measurement category
03 Efficiency category
04 Efficiency grade N
05 Variable speed drive
06 Year of manufacture
07 Manufacturer
08 Type
09 Power consumption P / kW 0.86
ed
09 Air flow q / m³/h
v
09 Pressure increase total p /
sf
Pa
10 Speed n / min -1
*
11 Specific ratio
12 Recycling/disposal
13 Maintenance
14 Additional components
* Specific ratio = 1 + p / 100 000 Pa
fs
Data obtained at optimum efficiency level. The ErP data is determined using a motor-impeller
combination in a standardized measurement setup.
Item no. 50442-5-9970 · ENU · Change 89187 · Approved 2016-04-14 · Page 5 / 12
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
Actual Req. 2015
41.9 33.3
A
Static
48.6 40
Yes
The year of manufacture is specified on the
product's rating label.
ebm-papst Mulfingen GmbH & Co. KG
Amtsgericht (court of registration) Stuttgart
· HRA 590344
D-74673 Mulfingen
A3G710-AO81-03
11370
105
905
1.00
Information on recycling and disposal is
provided in the operating instructions.
Information on installation, operation and
maintenance is provided in the operating
instructions.
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.

3.4 Technical description

Weight 12.3 kg
Fan size 710 mm
Rotor surface
Painted black
Electronics housing Die-cast aluminum, painted black
material
Blade material Sheet aluminum insert, sprayed with PP
plastic
Number of blades 5
Blade pitch 0°
Airflow direction "V"
Direction of rotation Counterclockwise, viewed toward rotor
Degree of protection IP54
Insulation class "B"
Moisture (F) /
F4-1
Environmental (H)
protection class
Installation position
Shaft horizontal or rotor on bottom; rotor
on top on request
Condensation On rotor side
drainage holes
Mode S1
Motor bearing Ball bearing
Technical features
- Output 10 VDC, max. 10 mA
- Output 20 VDC, max. 50 mA
- Output for slave 0-10 V
- Input for sensor 0-10 V or 4-20 mA
- Alarm relay
- Integrated PID controller
- Motor current limitation
- PFC, passive
- RS-485 ebmBUS
- Soft start
- Control input 0-10 VDC / PWM
- Control interface with SELV potential
safely disconnected from supply
- Thermal overload protection for
electronics/motor
- Line undervoltage / phase failure
detection
Touch current <= 3.5 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Electrical hookup Via terminal box
Motor protection
Thermal overload protector (TOP)
internally connected
with cable Variable
Protection class I (with customer connection of protective
earth)
Conformity with EN 61800-5-1; CE
standards
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.