Fastener Depth Control Adjustment - DeWalt DPN9033-XJ Original Instructions Manual

Pneumatic framing & coil nailers

Hide thumbs Also See for DPN9033-XJ:

Original instructions manual (60 pages)

Manual (60 pages)

page of 60

/ 60
Bookmarks

Available languages

3. Close magazine: Release pusher by first pulling back

on the pusher and then pressing the release tab. Slide

pusher against the nails. (Fig. 3)

DPN90C-XJ / DPN75C-XJ / DPN64C-XJ

1. Open the magazine: Pull down on the latch and swing

the door open. Swing magazine cover open. (Fig. 4)

2. Check adjustment: the nailer must be set for the length

of nail to be used. Nails will not feed smoothly if the

magazine is not correctly adjusted.

To change the setting:

The magazine contains an adjustable nail platform on which

the nail coil rests.

The nail platform can be adjusted up and down to three or

4 nail settings. To change settings, pull up on the post and

twist to the correct step. (Fig. 5)

Step

DPN90C-XJ

50-65mm

70-75mm

80-90mm

3. Load the coil of nails: Place the coil of nails over the

post in the magazine. Uncoil enough nails to reach the

feed pawl. Place the first nail in front of the front tooth

on the feed pawl, in the driver channel. The nail heads

must be in the slot in the nose. (Fig. 6)

4. Swing the door/magazine cover closed. Check that the

latch engages when released. (If it does not engage,

check that the nail heads are in the slot in the nose.)

NOTE: DPN64C-XJ / DPN75C-XJ ONLY

Removal of plastic strip: As nails are driven, the plastic

strip will feed out of the tool. When sufficient strip has

been fed out, it can be torn away by pulling against the

tear edge in the nose. (Fig. 7)

REMOVING NAILS

(DPN9033-XJ / DPN9033SM-XJ /

DPN9021PL-XJ / DPN9017PL-XJ)

1. Disconnect the tool from the air supply

2. Pull pusher back until it is securely engaged (Fig. 8)

3. Slide nails back to opening and push out

DPN64C-XJ

DPN75C-XJ

32-40mm

38-40mm

45-50mm

55-64mm

55-60mm

65-75mm

CAUTION: The pusher and pusher spring (constant

force spring).

Caution must be used when removing nails, as if

pusher is disengaged from latch it could spring

forward potentially pinching your hand.

Extra caution should be taken when carrying out

maintenance on the magazine area of the tool. The

spring is wrapped around but not attached to a roller.

If the spring is stretched beyond its length, the end

will come off the roller and the spring will roll up with

a snap, with a chance of pinching your hand. Also the

edges of the spring are very thin and could cut your

hand. Care must also be taken to insure no permanent

kinks are put in the springs as this will reduce the

springs force.

GUIDE ROD INSTALLATION AND REMOVAL

(DPN9033-XJ / DPN9033SM-XJ /

DPN9021PL-XJ / DPN9017PL-XJ)

Step 1 (Fig. 9): Locate guide (A); Pull and rotate cover (B).

Step 2 (Fig. 10): Locate access windows for installation

and removal of guide rod (C); Locate guide rod storage

channel (D); Rotate cover open to install or remove guide

rod (E); Install or remove guide rod through rear

of magazine (F).

Step 3 (Fig. 11): Install guide rod through (G) for 2.8mm

to 3.3mm shank nails. Rotate cover (B) to close; Install

guide rod through (H) for 3.3mm to 4.1mm shank nails.

Rotate cover (B) to close.