Advertisement
4.2.
BLADE LUBRICATION
4.2.1.
Lubrication will be required when cutting materials such as:
aluminium, copper, steel and iron which produce swarf likely to adhere to the blades.
4.2.2.
Lubrication is achieved by inserting a wax stick (figs.1.10 & 2.10) into the feed aperture
(figs.1.13 & 2.13) and winding in with the feed knob (figs1.11 & 2.11) until the tip of the
wax stick touches the blades.
4.2.3.
Wind more wax in periodically by means of the feed knob to replenish the supply of
lubricant.
5.
MAINTENANCE
5.1.
CHANGING BLADES
WARNING: Use only the blades specified for this machine. Other blades may not have the
correct clearances resulting in damage to the machine and injury.
WARNING: Isolate from the power supply and allow to cool before carrying out any
maintenance.
Wear protective gloves before touching blades.
To remove blades:
5.1.1.
Press the spindle lock (fig.1.1).
5.1.2.
Undo the clamping screw by turning it anticlockwise using the wrench supplied
(fig.1.12 & Fig.3).
5.1.3.
Push back the blade guard.
5.1.4.
Remove the clamping screw and the spacer.
5.1.5.
Lift the outer saw blade and remove.
5.1.6.
Lift the inner saw blade from its locating pins and remove.
To refit blades:
5.1.7.
Fit the inner blade. Locate holes with locating pins (the blade will only fit facing the correct
way). Ensure that the blade is sitting correctly on the centre boss.
See (fig.4)
Place the outer blade on the boss MAKING SURE THAT THE TEETH FACE THE TEETH
5.1.8.
ON THE INNER BLADE (fig.5).
5.1.9.
Refit the spacer and clamping screw.
5.1.10.
Finger tighten the clamping screw, ensuring that the spacer is located centrally.
5.1.11.
Engage the spindle lock and tighten fully using the wrench.
5.2.
BLADE GUARD
5.2.1.
DO NOT make any adjustments or modifications to the blade guard.
5.2.2.
Before each use of the saw, ensure that the blade guard has full and free movement.
If any fault is found with the blade guard, DO NOT use the machine; have it checked and
5.2.3.
repaired by a competent person.
5.2.4.
If the saw is dropped, check the blade guard for damage before further use.
5.3.
CARBON BRUSH REPLACEMENT
5.3.1.
If excessive sparking is noticed from within the machine, check the condition of the carbon
brushes. These will wear down with use and are a consumable item.
WARNING: Ensure that the saw is disconnected from the power supply.
5.3.2.
To check the brushes: Unscrew the brush holder caps (fig.6, on either side of the machine).
5.3.3.
Removing the caps will reveal the carbon brush assemblies (fig.7.)
5.3.4.
Gently pull on the spring caps to withdraw the brushes.
5.3.5.
If the brushes are worn down, obtain replacements from your Sealey dealer. Always
replace both brushes at the same time.
5.3.6.
Replacement is the reverse of 5.2.3 and 5.2.4.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. Contact your local solid waste authority for recycling information.
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack Sealey Limited
Dispose of this product at the end of its working life in compliance with the EU Directive on
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
Environmental Protection
WEEE Regulations
01284 757500
01284 703534
fig.2
fig.3
fig.4
fig.5
fig.6
fig.7
www.sealey.co.uk
sales@sealey.co.uk
SCT125
Issue:1 - 13/11/14
Advertisement
