The Radio - Panasonic RX-ES27 Operating Instructions Manual

7
A 3
7
1
7
○ ○ ○ ○ ○ ○ ○
2
7
○ ○ ○ ○ ○ ○ ○
3
7
B
7 7
2 3
•
7
1
TUNER
7
○ ○ ○ ○ ○ ○ ○
2
AUTO SCAN
7
○ ○ ○ ○ ○ ○ ○
3
AUTO SCAN
7
C
FM MODE/BP
7
D
FM
Downloaded From Disc-Player.com Panasonic Manuals
14
7 7
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
7
PRESET EQ
TAPE TUNER CD
1
S.VIRTUALIZER REW FF
AUTO SCAN
PRESET TUNE
CD SKIP
– VOLUME +
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Indicates auto scan
!"#
wJOðUÄuðË_« ` *« 5³¹
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
FM MODE/BP C RESET RANDOM REPEAT
PRESET EQ
TAPE TUNER CD
S.VIRTUALIZER REW FF
AUTO SCAN
PRESET TUNE
CD SKIP
VOLUME
AM

The Radio

2
Preparation: (when using batteries) Press [
A
Normal tuning
Press [TUNER BAND] to select "FM" or "AM".
1
(Unit comes on when using AC power.)
Each time you press the button:
AM ↔ FM
Press [ REW/–/Q
2
station.
"
Press [+, – VOLUME] to adjust the volume.
3
○ ○ ○ ○ ○ ○ ○ ○
B
Using auto scan
Remote control only
You can search for a station by listening to all tuned-in stations for 8
seconds each.
Press [TUNER] to select "FM" or "AM".
1
○ ○ ○ ○ ○ ○ ○ ○
Press [AUTO SCAN].
2
Auto scan starts.
Press [AUTO SCAN] when you find the desired
3
station.
Auto scan ends when it reaches the original frequency again.
To stop during the process, press [AUTO SCAN].
C
If noise is excessive in FM
Remote control only
Press [FM MODE/BP] to display "
Monaural sound is selected ("
reception is weak.
Press [FM MODE/BP] again to cancel the mode.
Auto-tuning
Press and hold [REW / – / Q] or [R / + / FF] until the frequency
○ ○ ○ ○ ○ ○ ○ ○
starts changing rapidly.
The frequency stops when it finds a station. (Interference may also
cause it to stop. Start auto-tuning again if this occurs.)
To stop auto-tuning
Press [REW / – / Q] or [R / + / FF].
D To improve reception
FM: Change the length and direction of the antenna.
AM: Change the facing of the unit.
○ ○ ○ ○ ○ ○ ○ ○ Note
• AM reception is briefly interrupted if [0 DECK] is pressed.
• To improve reception when using the unit in a building or vehicle,
use it near a window.
AM allocation setting
Only from the main unit
Before receiving AM broadcasts, be sure to select the correct alloca-
1
tion setting (either 9 kHz or 10 kHz) for your area.
2
Press [TUNER BAND] to select FM.
Press and hold [TUNER BAND] for approximately 5
seconds.
The frequency display will be returned to the minimum frequency
of the AM band and the display will begin to flash. Keep holding
3
for approximately 5 more seconds.
When the display stops flashing and indicates a
different frequency number, release [TUNER BAND].
To return to the original frequency, repeat steps
Note
After changing the "allocation" setting, the frequencies you
previously preset into the memory will be cleared.
Q ] or [ R Q Q R /+/FF ] to select a R R
Q R
" is displayed during FM stereo broadcasts.
MONO ".
" goes off) and noise reduces when
/I
].
1 3
to above.