TABLE OF CONTENTS JOB SPECIFICATION SHEET TABLE OF CONTENTS ............2 Job Number: ______________________________________________ JOB SPECIFICATION SHEET ..........2 Model Number: ____________________________________________ California Proposition 65 Warning ........2 Water Hardness: __________________________________ ppm or gpg TIMER FEATURES ..............3 Capacity Per Unit: __________________________________________ TIMER OPERATION ..............4 Mineral Tank Size: ___________ Diameter: ________Height: ________ MASTER PROGRAMMING MODE CHART ......5 Salt Setting per Regeneration: ________________________________...
TIMER FEATURES Setting the Time of Day 1. Press and hold either the Up or Down buttons until the Parameter Data programming icon replaces the service icon and the Display Display Indicator parameter display reads TD. Error/ Information Icon 2. Adjust the displayed time with the Up and Down buttons. 3.
TIMER OPERATION Manually Initiating a Regeneration 1. When timer is in service, press the Extra Cycle button for Meter Immediate Control 5 seconds on the main screen. A meter immediate control measures water usage and regenerates the system as soon as the calculated system 2.
MASTER PROGRAMMING MODE CHART CAUTION Before entering Master Programming, please contact your local professional water dealer. To enter Master Programming, set time to 12:01 PM. Master Programming Options Abbreviation Parameter Option Options Abbreviation Gallons Display Format Liters dF1b Downflow/Upflow Single Backwash dF2b Downflow Double Backwash Fltr...
MASTER PROGRAMMING MODE 2. Valve Type (Display Code VT) When the Master Programming Mode is entered, all available option setting displays may be viewed and set Press the Extra Cycle button. Use this display to set the Valve as needed. Depending on current option settings, some Type.
MASTER PROGRAMMING MODE CONTINUED 8. Reserve Selection (Display Code RS) Press the Extra Cycle button. Use this display to set the Safety 5. Tank in Service (Display Code TS) Factor. Use this display to select the type of reserve to be used in your system.
14. Day of Week Settings MASTER PROGRAMMING MODE CONTINUED Press the Extra Cycle button. Use this display to set the 11. Day Override (Display Code DO) regeneration schedule for a system configured as a Day of Press the Extra Cycle button. Use this display to set the Week control.
USER PROGRAMMING MODE 5. Press the Extra Cycle button. Use this display to adjust the Fixed Reserve Capacity. This option setting is identified by “RC” or "SF" in the upper left-hand Corner User Programming Mode Options of the screen. Abbreviation Parameter Description Day Override...
DIAGNOSTIC PROGRAMMING MODE 5. Press the Up button. Use this display to view the Volume Used since the last regeneration cycle. This option setting is identified by “VU” in the upper left hand corner Diagnostic Programming Mode Options of the screen. Abbreviation Parameter Description...
3/4-INCH PLASTIC TURBINE METER ASSEMBLY 19797 Rev A Item No. Part No. Description 1 ....1 ..19791-01 ..Meter Cable Assembly, 16 inch long with connector 2 ....2 ..19569 ....Clip, Flow Meter 3 ....2 ..13314 ....Screw, Slot Ind Hex, 8-18 x .60 4 .......
1-INCH STAINLESS STEEL METER ASSEMBLY Item No. Part No. Description Item No. Part No. Description 4 ....1 ..19791 ....Meter Cable Assembly, 1 ....1 ..62049-01 ..Service Kit, ..19791-02 ..Meter Cable Assembly, 1 inch & 1-1/2 inch Meter, 28 inch long with connector Standard Range ..
1-1/2 INCH STAINLESS STEEL METER ASSEMBLY Item No. Part No. Description Item No. Part No. Description 4 ....1 ..19791 ....Meter Cable Assembly, 1 ....1 ..62049-01 ..Service Kit, 1 inch & 1-1/2 inch Meter, ..19791-02 ..Meter Cable Assembly, Standard Range 28 inch long with connector 1 ..
TROUBLESHOOTING Error Codes Error codes appear on the In Service display. NOTE: Error Code Error Type Cause Reset and Recovery Cam Sense The valve drive took longer Unplug the unit and examine the powerhead. Verify that all cam Error than 6 minutes to advance to switches are connected to the circuit board and functioning the next regeneration position properly.
Page 28
For a detailed list of where Pentair trademarks are registered, please visit waterpurification.pentair.com/brands. § Pentair trademarks and logos are owned by Pentair plc or its affiliates. Third party registered and unregistered trademarks and logos are the property of their respective owners.