Related Manuals for Fisher & Paykel CI302CTB1
Summary of Contents for Fisher & Paykel CI302CTB1
-
Page 1: Installation Instructions
INSTALLATION INSTRUCTIONS Induction cooktop CI302CTB1 , CI604CTB1, CI704CTB1, CI804CTB1, CI904CTB1 models NZ AU GB IE HK SG www.fisherpaykel.com 591060B 02.16... -
Page 3: Safety And Warnings
SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS WARNING! Electrical shock hazard Particular attention shall be given to Disconnect the appliance from ● ● the relevant requirements regarding the mains electricity supply ventilation. before carrying out any work or Read these instructions carefully before ●... - Page 4 SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS if the cooktop is installed above an oven, Before you install the appliance, please make sure that a suitable disconnection switch is ● ● the oven has a built-in cooling fan. ●...
-
Page 5: Parts Supplied
PARTS SUPPLIED Foam tape (1) Clamping brackets (4) and screws (4) CI302CTB only Clamping brackets (2) and screws (2) Installing multiple products Note: We recommend installing products in separate cutouts with a minimum distance of 5 mm between the glass edges. ●... - Page 6 PRODUCT & CABINETRY DIMENSIONS * Note: CI604CTB, CI704CTB1, CI804CTB, CI904CTB models Electrical connection is made at the centre rear. CI302CTB models Electrical connection is made at the left rear. PLAN PLAN Note cutout position is centred to the cooktop. FRONT FRONT PROFILE * POWER CORD...
-
Page 7: Clearance Dimensions
CLEARANCE DIMENSIONS Alternatively 50mm holes min. 4 mm in side wall to allow adequate min. 75 mm Drawer or other obstruction cool air Alternatively 50mm holes min. 4 mm in side wall to allow adequate Oven with cooling fan cool air 20 mm WARNING! Ventilation gap... - Page 8 FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED) WARNING! We do not recommend flush mounting and sealing as servicing requires the cooktop to be removed from the benchtop. The owner carries all risk for flush mounting the cooktop. The owner must ensure the cooktop has been cut out from the benchtop before servicing can be carried out.
- Page 9 FLUSH MOUNTING INSTALLATION (NOT RECOMMENDED) 5 mm 5 mm 5 mm ROUTER THE BENCHTOP TO THE SPECIFIED DEPTH FIT THE CLAMPING BRACKETS MASK OFF THE AREA TO BE SILICONED 16 - 50mm 16 - 50mm No. of brackets and slot positions depends on model view from below min.
- Page 10 DISCARD PACKAGING PLACE COOKTOP UPSIDE DOWN IMPORTANT! - To avoid damage to the glass, ensure there is a protective cover underneath it. Recycle responsibly APPLY ADHESIVE FOAM TAPE AROUND GLASS EDGE LOWER GENTLY INTO THE CUTOUT IMPORTANT! Beware sharp edges Ensure edge of tape Foam Tape lines up with outer...
-
Page 11: Connecting The Cooktop To The Mains Power Supply
CONNECTING THE COOKTOP TO THE MAINS POWER SUPPLY IMPORTANT! This cooktop must be connected to the mains power supply only by a suitably qualified Ensure cable ● ● clamp is tightened person. with screw To connect the cooktop to the mains power supply, do not use adapters, reducers, or (you may have ●... -
Page 12: Final Checklist
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Is the cooktop earthed? Have you demonstrated the basic operation to the customer? Check that there is an adequate and constant flow of cool air from the cabinetry to the Make sure you explain to the customer about base of the cooktop. - Page 16 www.fisherpaykel.com Copyright © Fisher & Paykel Appliances. 2015. All rights reserved. The product specifications in this booklet apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available.