Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Auto Test autostop maxi
Summary of Contents for Auto Test autostop maxi
- Page 1 User Manual Version 8.18 STOP AUTO Maxi I n V e h i c l e B r a k e T e s t e r...
-
Page 2: Table Of Contents
Downloading Data ......................8 3.2.1 Download Instructions ....................8 CHECKING SENSORS AND OTHER FUNCTIONS ............. 10 CALIBRATION PROCEDURE ....................11 Return of AutoStop Maxi for Calibration ................ 11 5.1.1 Packaging ........................11 5.1.2 Shipping ......................... 11 5.1.3 Documentation ......................12 TROUBLESHOOTING ...................... -
Page 3: Autostop Maxi User Manual Version 8.18
Congratulations on your choice of an AutoTest Brake Meter. Please take the time to read this User’s Manual before using the AutoStop Maxi Brake Meter in the field. Incorrect or inappropriate use of this instrument may void the warranty. Retain the packing materials for future shipping and transport of the unit for periodic calibration. -
Page 4: Use Of Battery Charger And Care Of Battery
If the Brake Meter is used more frequently, the battery should be recharged daily. The AutoStop Maxi is fitted with a low voltage cut-out switch in the circuitry to protect the battery from excessive discharge. If the battery is allowed to discharge to zero (0) volts, and left standing for a long period of time, severe sulfation would occur, raising the internal resistance of the battery to abnormally high levels. -
Page 5: Operation
The head wind should be less than 10kph. 2.3 Set-Up in Vehicle AutoStop Maxi must be secure during the entire duration of the test. Misalignment or movement can cause lower (worse) deceleration readings. This could mean test failure if the brake performance is close to the required limits. -
Page 6: Special Characters
To obtain the following characters, press and hold the “-“ key, then press the listed character to obtain the special character. Press “-“ and HOLD, Displayed Character Press “-“ and HOLD, Displayed Character then Press: then Press: “ (SPACE) “ & ‘ & ‘ AutoStop Maxi User Manual Version 8.18 Page 5... -
Page 7: Test Instructions Summary
Slope too large, adjust unit. The deceleration and pedal LCD will then return to Ready> pressure. Pressing “A“ will abort the test. AutoStop Maxi User Manual Version 8.18 Page 6... - Page 8 Repeat the test by pressing Repeat? Y/N Press “Y” or “N” Svrc/Emrg? S/E if “Y” is “Y”, stop testing and return to pressed, Ready> if “N” is Ready mode by pressing “N” pressed AutoStop Maxi User Manual Version 8.18 Page 7...
-
Page 9: Test Data Storage (Optional)
3.2 Downloading Data The downloadable model of the AutoStop Maxi is provided with a serial port to attach to any IBM or IBM compatible computer with a spare COM port. An interface cable and download software are required to download test results from the Brake Meter. - Page 10 Connect your Brake Meter via the supplied RS232 cable to a spare Com Port of your computer. If your brake meter is supplied with a USB cable, connect one end of the cable to the PC and the other end to your Brake Meter. AutoStop Maxi User Manual Version 8.18 Page 9...
-
Page 11: Checking Sensors And Other Functions
Press Screen Display Check battery life “B” Bat. life: xxx % The Battery is considered flat when the percentage falls below 85% Check calibration Cal: x.xx g Acceleration reading “C” AutoStop Maxi User Manual Version 8.18 Page 10... -
Page 12: Calibration Procedure
LCD screen will show: “Calibration due! Contact your vendor for recalibration.” Return Brake Meter to AutoTest Products (See Section 6.1). 5.1 Return of AutoStop Maxi for Calibration 5.1.1 Packaging The Brake Meter should be packaged in the original shipping container. However, where this container is not available, remember that you are shipping an electronic instrument. -
Page 13: Documentation
For instructions on returning products for calibration or servicing, see Section 6.1. 7. SPECIFICATIONS AutoStop Maxi Brake Tester Battery 12 V. 1.9 AH fully sealed lead acid rechargeable Charger Output 14 V DC regulated, center positive, 500 mA AutoStop Maxi User Manual Version 8.18 Page 12... -
Page 14: Changing Paper
7. Prepare a clean starting edge on the new roll by cutting off the top of the paper. 8. Mount the paper roll on the spindle and load into the paper holder orientation shown on the printer cover. AutoStop Maxi User Manual Version 8.18 Page 13... -
Page 15: Changing Printer Ribbon
5. Wind up any slack in the paper roll, replace the printer cover plate fitted with the new paper roll and press the hold-down buttons home. Note: The buttons must be correctly aligned before they will click home. 6. Press “Off” when complete. AutoStop Maxi User Manual Version 8.18 Page 14... -
Page 16: Warranty
AutoTest Products or any Authorised Service Center is not responsible for incidental or consequential damages resulting from the breach of any express or implied warranty, including damage to property and, to the extent permitted by law, damages for personal injury. AutoStop Maxi User Manual Version 8.18 Page 15... -
Page 17: Quick Guide
The battery must never be allowed to fully discharge as it will void the warranty. Set-Up & Testing 1. Secure AutoStop Maxi in vehicle and attach pedal sensor to brake pedal. This will vary from vehicle to vehicle; a mounting bracket or straps may be used. - Page 18 NOTES: AutoStop Maxi User Manual Version 8.18 Page 17...
- Page 19 AutoStop Maxi User Manual Version 8.18 Page 18...
- Page 20 AUTOTEST Products Pty Ltd 279 Normanby Road, Port Melbourne. VIC 3207 Australia Phone: (+61 3) 9647 9797 Sales:(+61 3) 9647 9707 Service:(+61 3) 9647 9706 Fax: (+61 3) 9646 3427 Email:service@autotest.net.au sales@autotest.net.au info@autotest.net.au www.autotest.net.au...
Need help?
Do you have a question about the autostop maxi and is the answer not in the manual?
Questions and answers