Compound Mitre Cuts; Care And Maintenance; Changing The Saw Blade - Metabo KS 210 Operating Instructions Manual

ENGLISH
Cutting the work piece:
1. Loosen the bevel tilt setting lock
screw (40) at the rear of the saw.
2. Tilt the sawhead slowly into the
desired position.
3. Tighten the bevel tilt setting lock
screw.
4. Hold work piece against the fence.
5. Press and hold the ON/OFF switch.
6. Swing the safety lock to the side
(see "Standard Crosscuts").
7. Slowly swing the sawhead fully
down, holding the handle firmly.
When sawing, exert only moderate
pressure to prevent the motor speed
to drop too much.
8. Cut work piece in a single pass.
9. Release the ON/OFF switch and let
the sawhead slowly return to its
upper starting position.
8.4

Compound Mitre Cuts

3
Note:
The compound mitre cut is a
combination of mitre and bevel cut. This
means the work piece is cut at an angle
other than 90° against the rear guide
edge and against its surface.
A
Danger!
When cutting
mitres the saw blade is much more
exposed than normally - increased
risk of injury. Always keep sufficient
distance to the saw blade.
Maximum work piece dimensions (in
mm) at 45° bevel tilt:
Width
approx.
15° 110
22.5° 105
30° 100
45° 80
Starting position:
Transport locking pin pulled out.
Sawhead fully raised.
20
Rotating table locked in desired
position.
Sawhead tilted to desired angle
against the work piece's surface and
locked.
Cutting the work piece:
1. Hold work piece against the fence.
2. Press and hold the ON/OFF switch.
3. Swing the safety lock to the side
(see "Standard Crosscuts").
40
4. Slowly swing the sawhead fully
down, holding the handle firmly.
When sawing, exert only moderate
pressure to prevent the motor speed
to drop too much.
5. Cut work piece in a single pass.
6. Release the ON/OFF switch and let
the sawhead slowly return to its
upper starting position.

9. Care and Maintenance

A
Danger!
Unplug before servicing.
Repair and maintenance work other
than described in this section should
only be performed by trained and
qualified personnel.
Replace defective parts, especially
of safety devices, only with OEM
replacement parts. Parts not tested
and approved by the manufacturer
can cause unforeseen damage.
Check that all safety devices are
operational again after each service.
9.1

Changing the Saw Blade

A
Danger!
Directly after cutting the saw
blade can be very hot – burning
hazard! Let a hot saw blade cool
down. Do not clean a hot saw
blade with combustible liquids.
compound
Risk of injury, even with the saw
blade at standstill. When loosen-
ing and tightening the arbor bolt,
the retractable blade guard must
encompass the saw blade. Wear
gloves when changing blades.
Laser radiation hazard!
Always disable the laser guide
Height
when servicing the machine!
approx.
1. Arrest sawhead assembly in the
40
upper position with the transport
lock.
40
2. Unscrew screw (41) fully.
40
40
3. Swing the retractable blade guard
(43) up.
4. Loosen screw (42) on the right.
5. Fully unscrew Allen head screw
(45).
6. Lift blade cover (43) and flange
guard (44) and put
wrench on the arbor bolt.
S
42
45 44
7. To keep the saw blade from turning
press the lock knob (46), while at
the same time turning the saw blade
by hand until the
engages.
8. Remove arbor bolt (47) from the
saw spindle with the assembly
wrench (left-hand thread!).
9. Remove the outer blade flange and
the saw blade from the saw spindle.
A
Danger!
Do not use cleaning agents
(e.g. to remove resin residue) which
would tend to corrode the light metal
components of the saw; the stability
of the saw could be compromised.
41
assembly
43
blade lock
46