Before You Begin - Weslo CADENCE 1020 WETL28090 User Manual

BEFORE YOU BEGIN

Thank you for selecting the WESLO CADENCE ¨ 1020
treadmill. The CADENCE 1020 treadmill combines
advanced technology with innovative design to let you
enjoy an excellent form of cardiovascular exercise in
the convenience and privacy of your home. And when
youÕre not exercising, the unique CADENCE 1020 can
be folded up, requiring less than half the floor space of
other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
Speed Control
Water Bottle Holder
(Bottle not included)
Handrails
Storage Latch
Walking Belt
Foot Rails
BACK
Rear Roller
Adjustment Bolts
please call our Customer Service Department at 0345-
089009. To help us assist you, please note the product
model number and serial number before calling. The
model number of the treadmill is WETL28090. The
serial number can be found on a decal attached to the
treadmill (see the front cover of this manual for the
location).
Before reading further, please review the drawing
below and familiarise yourself with the parts that are
labelled.
Console
Accessory Tray
Book Rack
Key/Clip
Handrail
Knobs
Circuit Breaker
Cushioned Deck
Incline Leg
RIGHT SIDE
4
PROBLEM: The walking belt is off-centre or slips when walked on
SOLUTION: a. If the walking belt has shifted to the left, first
remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller adjust-
ment bolt clockwise, and the right bolt counterclock-
wise, 1/4 of a turn each. Be careful not to overtighten
the walking belt. Plug in the power cord, insert the
key and run the treadmill for a few minutes. Repeat
until the walking belt is centred.
b. If the walking belt has shifted to the right, first
remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller adjust-
ment bolt counterclockwise, and the right bolt clock-
wise, 1/4 of a turn each. Be careful not to overtighten
the walking belt. Plug in the power cord, insert the
key and run the treadmill for a few minutes. Repeat
until the walking belt is centred.
c. If the walking belt slips when walked on, first
remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn both rear roller adjust-
ment bolts clockwise, 1/4 of a turn. When the walking
belt is correctly tightened, you should be able to lift
each side of the walking belt 5 to 7 cm off the walking
platform. Be careful to keep the walking belt centred.
Plug in the power cord, insert the key and run the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. If an extension cord is needed, use only a 3-conductor, 14-gauge (1mm
than 5 feet (1.5 meters).
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may be
permanently damaged. Remove the key and
UNPLUG THE POWER CORD. Using the allen
wrench, turn both rear roller adjustment bolts counter-
clockwise, 1/4 of a turn. When the walking belt is
properly tightened, you should be able to lift each
side of the walking belt 5 to 7 cm off the walking plat-
form. Be careful to keep the walking belt centred.
Plug in the power cord, insert the key and run the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
c. If the walking belt still slows when walked on, please call our Customer Service Department.
a
b
c
2 ) cord that is no longer
b
5Ð7 cm
Rear Roller
Adjustment Bolts
13