Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for STARTRITE 352SB
Summary of Contents for STARTRITE 352SB
-
Page 1: Instruction Manual
Woodworking Bandsaws Instruction Manual 352SB 401S 440R 501S 581S 681S... - Page 2 Index GENERAL INFORMATION Foreword Warranty MACHINE DESCRIPTION Machine identification CE Certificate Technical specification Recommended protective clothing Noise emission Prescribed use of the machine Hazards INSTALLATION Hoisting and unloading Position of the machine Electrical connection - start up Connecting the dust extraction system USING THE MACHINE Principal machine groups Choice and maintenance of blade...
-
Page 3: General Information
Packing Dimensions cm 189x53x84 189x53x84 199x53x84 207x52x94 210x55x107 230x60x120 255x65x125 Nett Weight kg 352SB* Additional features and educational safety system • Ceramic blade guide system • Lockable isolator • Two speed motor in 3 phase model • Lockable keyswitch •... -
Page 4: Noise Emission
2.4 RECOMMENDED PROTECTIVE CLOTHING • Gloves for moving work material and when carrying out the blade changes; • Non-slip shoes; • Protective eye glasses. 2.5 NOISE EMISSION The measurements of noise, in the working position and during operation, were carried out under the standard ISO 7960 annex "J": Instantaneous acoustic pressure <130.0 dB The value of the noise level indicated is an emission level and doesn’t necessarily represent safe working levels. -
Page 5: Dust Extraction
PLEASE NOTE: 352SB 3 phase (2 speed) model the speed selector switch must be set at zero to switch the machine on. It is then started by turning the speed selection switch to speed 1 or 2. -
Page 6: Using The Machine
Re-tension before next next operation. • Misalignment of the bandwheels due to unauthorized intervention of the regulating screws of the lower bandwheel. • Irregularity of bandwheels surface, e.g an accumulation of sawdust whilst cutting resinous materials. 352SB* 401S 440R 501S... -
Page 7: Setting The Blade Guides
4.3 BLADE MOUNTING AND ADJUSTMENT When mounting the blade it is necessary to release the motor brake that prevents manual rotation of bandwheels. To release the brake, while machine is stopped, move the brake release selector (FIG. 10 & FIG.11 section 3.3) turning it toward the release symbol. -
Page 8: Cutting Direction And Parallelism
4.5 TABLE INSERT FOR DUST EXTRACTION The machines are equipped with a FIG. 20 removable plastic insert on the work- table, FIG.20, pos “B”, the relieved holes of the insert improve dust extraction. By adjusting the 4 screws at the bottom of the opening of the work-table it is possible to change the height of the insert in relation to the work surface. -
Page 9: Safety Advice
5. Safety Advice a) Machine out of order Before making any adjustments or repairs to the machine, disconnect from the electrical supply. If any faults are suspected, disconnect the electrical supply and put a visible notice on the machine. b) Before operating •... -
Page 10: Cutting Of Round Pieces
5.3 CUTTING OF ROUND PIECES FIG. 5.3 Use a wedge rest to prevent rotation of round parts during cutting. FIG. 5.3 5.4 WEDGE CUTTING FIG. 5.4 Pushing device for wedge cutting FIG. 5.4 5.5 CUTTING OF WEDGE-SHAPED LENGTHS FIG. 5.6 Equipment for cutting wedge-shaped lengths. -
Page 11: Braking System
6. Braking System The machines are equipped with an electro-magnetic brake that ensure stopping all moving parts within 10 seconds, The brake pads of the braking system are subject to wear, it is recommended that they are checked regularly and replaced when necessary, to maintain the braking time within regulations fixed by the norms. -
Page 12: Maintenance
7. Maintenance BEFORE ANY INTERVENTION ALWAYS DISCONNECT THE ELECTRICAL SUPPLY! Periodically check that all screws are tightly fastened and the condition of the various guards V BELTS After the first few hours of operation it is necessary to check that the tension of the belts is correct,as they tend to stretch. To control the tension of the belts push the mid-point of the belt applying 3-4 Kg of pressure, the displacement should not exceed 5-6 mm. -
Page 13: Troubleshooting
EXAMPLE: TO ORDER LOWER FLY WHEEL FOR 781S Model: 781S Registration number: xyxyxyy Part number: 95 Quantity: 1 piece 9.1 DRIVE BELTS & BALL BEARING PART NUMBERS Model V-Belt Ball Bearings 352SB 3V335 6205 2RS 401S 3V335 6205 2RS 440R 3V755 x2 62062 RS... -
Page 14: Diagrams & Components
Diagrams & Components... - Page 23 Dust extractors Circular Saws Band Re-saws Panel saws Spindle Moulders Planer thicknessers Universals Planers Thicknessers Startrite Machines T: 0870 770 1777 E: info@startrite.co.uk Unit B, Ireland Industrial Est. F: 0870 770 1888 W: www.startrite.co.uk Adelphi Way, Staveley Chesterfield England S43 3LS...