Maintenance And Storage - Toro 22610 Operator's Manual

– Never refuel or drain the machine indoors.
•
Check that the operator presence controls, safety switches,
and shields are attached and functioning properly. Do not
operate unless they are functioning properly.
•
Check that the cutting wheel has stopped rotating when
you reduce the throttle.
Operation
•
Never run an engine in an enclosed area.
•
Only operate in good light, keeping away from holes and
hidden hazards.
•
Be sure all drives are in neutral before starting the engine.
Only start the engine from the operator's position.
•
Never operate with the guards not securely in place. Be
sure all interlocks are attached, adjusted properly, and
functioning properly.
•
Do not change the engine governor setting or overspeed
the engine.
•
Stop on level ground, lower the grinder, and shut off
the engine before leaving the operator's position for any
reason.
•
Keep hands and feet away from the moving grinder wheel
and teeth.
•
Look behind and down before backing up to be sure of
a clear path.
•
Keep pets and bystanders away.
•
Do not operate the machine under the influence of
alcohol or drugs.
•
Use care when loading or unloading the machine into a
trailer or truck.
•
Ensure that the area is clear of other people before
operating the machine. Stop the machine if anyone enters
the area.
•
Never leave a running machine unattended. Always stop
the engine and verify the cutting wheels has stopped
rotating.
•
Never jerk the controls; use a steady motion.
•
Watch for traffic when operating near or crossing
roadways.
•
Do not touch parts which may be hot from operation.
Allow them to cool before attempting to maintain, adjust,
or service.
•
Ensure that you operate the machine in areas where
there are no obstacles in close proximity to the operator.
Failure to maintain adequate distance from trees, walls,
and other barriers may result in injury as the machine
backs up during operation if the operator is not attentive
to the surroundings. Only operate the unit in areas where
there is sufficient clearance for the operator to safely
maneuver the product.
•
Before grinding, have the area marked for underground
utilities, and do not grind in marked areas.
•
Locate the pinch point areas marked on the machine and
keep hands and feet away from these areas.
•
Lightning can cause severe injury or death. If lightning
is seen or thunder is heard in the area, do not operate
the machine; seek shelter.

Maintenance and Storage

•
Stop the engine. Wait for all movement to stop before
adjusting, cleaning, or repairing.
•
Clean debris from the grinder, drives, mufflers, and engine
to help prevent fires. Clean up oil or fuel spillage.
•
Let the engine cool before storing and do not store near
flame.
•
Do not store fuel near flames or drain indoors.
•
Park the machine on level ground. Never allow untrained
personnel to service the machine.
•
Carefully release pressure from components with stored
energy.
•
Remove the spark plug wire before making any repairs.
•
Keep hands and feet away from moving parts. If possible,
do not make adjustments with the engine running.
•
Keep all parts in good working condition and all hardware
tightened. Replace all worn or damaged decals.
•
Keep nuts and bolts tight. Keep equipment in good
condition.
•
Never tamper with safety devices.
•
Keep the machine free of grass, leaves, or other debris
build-up. Clean up oil or fuel spillage. Allow the machine
to cool before storing.
•
Use extra care when handling gasoline and other fuels.
They are flammable and vapors are explosive.
– Use only an approved container.
– Never remove the gas cap or add fuel when the
engine is running. Allow the engine to cool before
refueling. Do not smoke.
– Never refuel the machine indoors.
– Never store the machine or fuel container inside
where there is an open flame, such as near a water
heater or furnace.
– Never fill a container while it is inside a vehicle, trunk,
pick-up bed, or any surface other than the ground.
– Keep container nozzle in contact with the tank during
filling.
•
Stop and inspect the equipment if you strike an object.
Make any necessary repairs before restarting.
•
Use only genuine Toro replacement parts to ensure that
original standards are maintained.
4