Advertisement
HOW TO ADJUST THE RESISTANCE STRAP
If there is not enough pedaling resistance when the
resistance control is turned to the highest setting, the
resistance strap may need to be adjusted. Follow the
steps below to adjust the resistance strap.
1. Turn the resistance control to the lowest setting.
Console
Strap
Clamp
Resistance
Control
2. Locate the strap clamp behind the console and
open it.
3. Grip the end of the resistance strap (not shown)
and pull it slightly. While holding the resistance
strap, fully close the strap clamp. Turn the pedals
for a moment to make sure that there is not too
much resistance.
HOW TO ADJUST THE DRIVE BELT
If the drive belt causes excessive noise or slips as
you pedal, follow the steps below to adjust the drive
belt.
1. Remove the left and right pedals. Then, remove
the screws that hold the side shields in place;
make sure to note the location of each screw.
Remove both side shields.
Side
Shields
Screws
2. Press down on the center of the drive belt between
the front and rear pulleys. There should be from
1/4" to 1/2" of movement in the center of the
drive belt.
Drive Belt
Flywheel
Adjustment
Nuts
Locknut
If the drive belt is properly adjusted, go to step 4.
3. If the drive belt needs to be adjusted, loosen the
indicated locknut on each side of the flywheel.
To tighten the drive belt, turn the adjustment nuts
clockwise; to loosen the drive belt, turn the adjust-
ment nuts counterclockwise. Make sure that the fly-
wheel is straight and tighten the locknuts.
4. Reattach the side shields and the pedals.
8
4. Loosen, but do not remove, the Handlebar Lever (8)
and the two Handlebar Bolts (11) that hold the
Handlebar Bracket (2) in place.
Slide the Handlebar (7) through the Handlebar
Bracket (2) until the Handlebar is in the position
shown. Note: If it is difficult to slide the Handlebar
into position, remove the Handlebar Bracket.
After the Handlebar (7) is in position, tighten the
Handlebar Lever (8) and the two Handlebar Bolts (11).
5. Attach the Seat (1) to the indicated brackets on the
Seat Frame (30) with the four Seat Screws (3).
6. Press the Backrest Frame Cap (63) into the
Backrest Frame (64). Attach the Backrest (62) to the
Backrest Frame with two Backrest Screws (48).
Attach the Backrest Frame (64) to the indicated
bracket on the Seat Frame (30) with a Frame Bolt
(28), two Frame Washers (29), and a Frame
Locknut (44).
Hold the Backrest Frame (64) in an upright position.
Insert a Lock Pin (47) into the indicated holes in the
bracket on the Seat Frame (30) and the Backrest
Frame.
7. The Console (15) requires two 1,5 V batteries (not
included). Alkaline batteries are recommended.
Insert two batteries into the battery compartment in
the back of the Console. Make sure that the nega-
tive ends of the batteries (marked "—") are
touching the springs in the battery compartment.
Slide the Console (15) onto the console bracket.
Connect the Reed Switch Wire (33) to the jack on
the back of the Console (15) through the hole in the
bracket on the Frame (16).
Identify the Left Pedal (25), which is marked with an
"L." Using an adjustable wrench, tighten the Left
Pedal counterclockwise into the left arm of the
Crank (24). Next, tighten the Right Pedal (not
shown) clockwise into the right arm on the Crank.
8. Make sure that all parts are properly tightened
before you use the exercise cycle.
4
5
10
30
5
7
2
11
9
5
1
30
3
6
62
64
48
28
29
47
29
30
44
7
Hole
15
33
24
16
Console
25
Bracket
5
9
8
63
Advertisement
