HP R/T2200 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. UPS
  5. R/T2200
  6. Installation instructions manual

HP R/T2200 Installation Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Enlarged version
HP R/T2200 UPS

Installation Instructions

© Copyright 2006, 2008 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only
warranties for HP products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should
be construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
Part Number 404313-004
August 2008 (Fourth Edition)
Overview
The HP UPS R/T2200 features power protection for loads up to
2200 VA/1600 W.
For more information about any of the topics covered in this
document, see the UPS user guide located on the documentation CD
or HP website (http://www.hp.com/go/rackandpower).
Precautions
Save these instructions. This document contains important safety
instructions that should be followed during installation, operation,
and maintenance of the UPS and batteries.
WARNING: A risk of personal injury from electric shock
and hazardous energy levels exists. The installation of
options and routine maintenance and service of this
product must be performed by individuals who are
knowledgeable about the procedures, precautions, and
hazards associated with AC power products.
WARNING: To prevent personal injury from earth
conductor leakage current:
Do not operate the UPS while disconnected from the
•
utility power source.
Disconnect load devices before disconnecting the UPS
•
from the utility power source.
WARNING: To prevent personal injury, prepare the area
and observe all materials handling procedures when
transporting the UPS. When fully assembled, the UPS
weighs 29 kg (64 lb).

Advertisement

Table of Contents
loading

Related Manuals for HP R/T2200

Summary of Contents for HP R/T2200

  • Page 1: Installation Instructions

    The information contained herein is subject to change without notice. The only Disconnect load devices before disconnecting the UPS • warranties for HP products and services are set forth in the express warranty from the utility power source. statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.

  • Page 2: Kit Contents

    Installing the UPS as a tower If you have the HP Enterprise Infrastructure Solutions Management Pack CD, use the CD to install HP Power Manager software. To download the latest version of HP Power Manager software and UPS Before installing the unit, review and adhere to all warnings firmware, see the HP website (http://www.hp.com/products/ups).

  • Page 3: Installing The Ups In A Rack

    From inside the bezel, gently push out the LED/Control panel, Attach the 2U side-mounting brackets to the unit. rotate it 90 degrees, and then replace it in the bezel. Loosen the wing nuts, and extend the brackets to the desired Replace the front bezel.

  • Page 4: Connecting The Batteries

    • Do not attempt to recharge batteries after removal from the unit. NOTE: The HP logo and product name are printed on the Do not disassemble, crush, or puncture the batteries. • RETMA rail covers; therefore, the HP logo badge is only used for a tower installation/configuration.

  • Page 5: Selecting The Ups Voltage Configuration

    DB9 serial cable included with the UPS. Install HP Power CAUTION: Do not set the Battery Charge Level switch to Manager software 4.1 or later on the host computer. See the HP the down position without an ERM connected. There is a website (http://www.hp.com/go/rackandpower) to download the...

  • Page 6: Connecting The Ground Bonding Cable

    Connecting the ground bonding cable The ground bonding screw is provided as an attachment point for conductors. Use a ground bonding cable if the rack contains any conductors for the purpose of functional grounding or bonding of ungrounded metal parts. The ground bonding cable is not included.

  • Page 7: Powering Up The Ups

    Powering up the UPS Press and hold the Power On/Standby button until the UPS beeps. The Power LED illuminates solid green, indicating that power is available at the UPS output receptacles.

Table of Contents