Electrolux E30SO75ESS Service Manual page 37

bottom plate.
30.Remove the thirteen (13) screws holding the convection
duct to the oven cavity and the heater duct upper.
31.Remove the convection duct assembly from the oven
cavity.
1. Disconnect the power supply cord.
2. Remove the outer case cabinet, referring to "OUTER
CASE CABINET REMOVAL".
3. Open the oven door and block it open.
4. Discharge the high voltage capacitor.
5. Remove the back plate from the oven, referring to
"BACK PLATE REMOVAL".
6. Remove the heater duct left assembly from the oven
1. Disconnect the power supply cord.
2. Remove the outer case cabinet, referring to "OUTER
CASE CABINET REMOVAL".
3. Open the oven door and block it open.
4. Discharge the high voltage capacitor.
5. Remove the back plate from the oven, referring to
"BACK PLATE REMOVAL".
6. Remove the convection duct assembly from the oven
cavity, referring to "HEATER DUCT LEFT ASSEMBLY,
HEATER DUCT UPPER
CONVECTION DUCT ASSEMBLY REMOVAL
1. Disconnect the power supply cord.
2. Remove the outer case cabinet, referring to "OUTER
CASE CABINET REMOVAL".
3. Open the oven door and block it open.
4. Discharge the high voltage capacitor.
5. Remove the back plate from the oven, referring to
"BACK PLATE REMOVAL".
6. Remove the heater duct left assembly from the oven
1. Disconnect the power supply cord.
2. Wait for 60 seconds to discharge the high voltage
capacitor.
3. Remove the turntable tray and the turntable support from
the oven cavity.
4. Lay the oven on its backside.
5. Remove the turntable motor cover by snipping off the
material in four corners.
6. Where the corners have been snipped off, bend corner
DOOR SENSING SWITCH, SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH REPLACEMENT
Removal
1. Disconnect the power supply cord.
32.Now, the convection duct assembly is free.
33.Remove the nine (9) screws holding the heater duct
34.Remove the heater duct upper from the oven cavity.
35.Now, the heater duct upper assembly is free.
SIDE HEATING ELEMENT REMOVAL
7. Remove the one (1) screw holding the heater mounting
8. Remove the two (2) nuts holding the side heating element
9. Now, the side heating element is free.
CONVECTION MOTOR REMOVAL
7. Loosen the one (1) screw holding the convection fan
8. Remove the four (4) screws holding the convection
9. Remove the six (6) screws holding the convection motor
10.Remove the convection motor from the convection
11.Now, the convection motor is free.
ASSEMBLY AND
TOP HEATING ELEMENT REMOVAL
7. Remove the one (1) screw holding the heater mounting
8. Remove the two (2) nuts holding the top heating element
9. Now, the top heating element is free.
TURNTABLE MOTOR REMOVAL
7. Disconnect the wire leads from the turntable motor.
8. Remove the one (1) screw holding the turntable motor to
9. Now, the turntable motor is free.
10.After replacement, use the one (1) screw to fit the
2. Remove the outer case cabinet, referring to "OUTER
35
upper to the oven cavity.
cavity, referring to "HEATER DUCT LEFT ASSEMBLY,
HEATER DUCT UPPER
CONVECTION DUCT ASSEMBLY REMOVAL
angle B to the heater duct left.
to the heater duct left.
assembly to the convection fan motor shaft with a
hexagon key wrench, and remove the convection fan.
motor mounting angle to the convection duct.
to the convection motor mounting angle.
motor mounting angle.
cavity, referring to "HEATER DUCT LEFT ASSEMBLY,
HEATER DUCT UPPER
CONVECTION DUCT ASSEMBLY REMOVAL
angle A to the heater duct upper.
to the heater duct upper.
areas flat. No sharp edges must be evident after removal
of the turntable motor.
the oven cavity bottom plate.
turntable motor cover.
CASE CABINET REMOVAL".
E30SO75ESS
ASSEMBLY AND
ASSEMBLY AND