This will ensure that the complete stop before placing it down. The safety of the power tool is maintained. tool insert can jam and lead to loss of control over the power tool. Bosch Power Tools 1 609 929 K81 | (21.4.08)
12 Scale for mitre angle maintain the tool and the accessories, keep the 13 Angle gauge** hands warm, organisation of work patterns. 14 Bolt hole 1 609 929 K81 | (21.4.08) Bosch Power Tools...
Senior Vice President Head of Product longer than required for the intended cut. Engineering Certification Use a thin saw blade for narrow curve cuts. 07.04.2008, Robert Bosch GmbH, Power Tools Division D-70745 Leinfelden-Echterdingen Bosch Power Tools 1 609 929 K81 | (21.4.08)
Page 10
Touch- tre cuts. ing or breathing-in the dusts can cause aller- gic reactions and/or lead to respiratory infec- tions of the user or bystanders. 1 609 929 K81 | (21.4.08) Bosch Power Tools...
Page 11
When the base plate 4 fully lays on the work- piece, continue sawing along the desired cutting line. Bosch Power Tools 1 609 929 K81 | (21.4.08)
Page 12
Circular Cuts (see figure G): Set the locking Check the guide roller 5 regularly. If worn, it must screw 17 to the other side of the parallel guide. be replaced through an authorised Bosch after- Slide the scale of the parallel guide through the sales service agent.
Page 13
Dublin 24 Tel. Service: +353 (01) 4 66 67 00 Fax: +353 (01) 4 66 68 88 Australia, New Zealand and Pacific Islands Robert Bosch Australia Pty. Ltd. Power Tools Locked Bag 66 Clayton South VIC 3169 Customer Contact Center...
Page 14
Une clé laissée fixée sur une partie tournante de l’outil peut d’eau à l’intérieur d’un outil augmentera le risque de choc électrique. donner lieu à des blessures de personnes. 1 609 929 K81 | (25.9.08) Bosch Power Tools...
Page 15
De nombreux accidents le. La lame de scie peut être endommagée, se sont dus à des outils mal entretenus. casser ou causer un contrecoup. Bosch Power Tools 1 609 929 K81 | (25.9.08)
Page 16
Déplier le volet sur lequel l’appareil est représenté de manière graphique. Laisser le volet déplié pen- dant la lecture de la présente notice d’utilisation. 1 609 929 K81 | (25.9.08) Bosch Power Tools...
Page 17
9 et le tourner dans le sens des prévue. aiguilles d’une montre jusqu’à ce que la lame Pour scier des courbes serrées, utiliser des la- de scie 6 soit bloquée. mes de scie fines. Bosch Power Tools 1 609 929 K81 | (25.9.08)
Page 18
Lorsque la plaque de base 4 est reculée, on ne peut travailler avec un angle d’onglet de 0°. Il ne faut pas non plus utiliser la butée parallèle avec dispositif pour coupes circulaires 18 (accessoi- re) et le pare-éclats 10. 1 609 929 K81 | (25.9.08) Bosch Power Tools...
Page 19
Il est recommandé de réduire le nombre de cour- ses quand la lame de scie est placée sur la pièce à travailler ainsi que pour scier des matières plas- tiques et de l’aluminium. Bosch Power Tools 1 609 929 K81 | (25.9.08)
Page 20
également sous : courant. www.bosch-pt.com Tenez toujours propres l’outil électroporta- Les conseillers techniques Bosch sont à votre tif ainsi que les ouïes de ventilation afin disposition pour répondre à vos questions con- d’obtenir un travail impeccable et sûr.
Page 21
Suyun elektrikli el aleti ç kar n. Aletin dönen parçalar içinde içine s zmas elektrik çarpma tehlikesini bulunabilecek bir yard mc alet yaralan- art r r. malara neden olabilir. Bosch Power Tools 1 609 929 K81 | (21.4.08)
Page 22
ğ n kontrol edin. Aleti kullanmaya başlamadan önce hasarl parçalar onart n. Birçok iş kazas elektrikli el aletlerinin kötü bak m ndan kaynaklan r. 1 609 929 K81 | (21.4.08) Bosch Power Tools...
Page 23
çarpmalar na, yang n- değildir) lara ve/veya ağ r yaralanmalara neden olunabilir. Lütfen aletin resminin göründüğü sayfay aç n ve bu kullan m k lavuzunu okuduğunuz sürece bu sayfay aç k tutun. Bosch Power Tools 1 609 929 K81 | (21.4.08)
Page 24
Veriler [U] 230/240 V’luk anma gerilimleri için geçerlidir. Daha düşük gerilimlerde ve ülkelere özgü tiplerde bu veriler değişebilir. Lütfen elektrikli el aletinizin tip etiketi üzerindeki ürün koduna dikkat edin. Tek tek aletlerin ticari kodlar değişik olabilir. 1 609 929 K81 | (21.4.08) Bosch Power Tools...
Page 25
Elektrikli el aletinin kendinde bir çal şma yap- madan önce her defas nda fişi prizden çekin. Talaş emniyeti 10 (aksesuar) ahşap malzemede 07.04.2008, Robert Bosch GmbH, Power Tools Division D-70745 Leinfelden-Echterdingen kesme yaparken üst yüzeyin y rt lmas n önler.
Page 26
0° gönye aç lar nda mümkündür. Ayr ca alüminyum ile plastikleri keserken düşük strok dairesel kesicili (aksesuar) paralellik mesnedi 18 say s tavsiye edilir. ve talaş emniyeti 10 kullan lmamal d r. 1 609 929 K81 | (21.4.08) Bosch Power Tools...
Page 27
30 mm olmal d r. K lavuz makaray 5 düzenli aral klarla kontrol Paralel kesme işleri (Bak n z: Şekil F): Tespit edin. Aş nan k lavuz makara yetkili bir Bosch vidas n gevşetin 17 ve paralellik mesnedi servisinde değiştirilmelidir.
Page 28
Demonte görünüşler ve yedek parçalara ait bilgileri şu adreste de bulabilirsiniz: www.bosch-pt.com Bosch müşteri servisi timi sat n alacağ n z ürünün özellikleri, bu ürünün kullan m ve ayar işlemleri hakk ndaki sorular n z ile yedek parçalar na ait sorular n z memnuniyetle yan tland r r.