Xerox WorkCentre 5222 Service Manual Field page 18

REP 16.1.3 H-Transport Belt .................................................................
REP 16.1.4 H-Transport Motor ..............................................................
REP 16.2.1 SB-Finisher Undocking ................................................................................
REP 16.2.2 Front Cover Assembly .................................................................................
REP 16.2.3 Rear Upper Cover........................................................................................
REP 16.2.4 Rear Lower Cover........................................................................................
REP 16.2.5 Eject Cover ..................................................................................................
REP 16.2.6 Foot Cover ...................................................................................................
REP 16.2.7 Stacker Lower Cover ...................................................................................
REP 16.2.8 Stacker Upper Cover ...................................................................................
REP 16.2.9 Stack Height Sensors 1 and 2 .....................................................................
REP 16.2.10 Sub Paddle Solenoid Assembly.................................................................
REP 16.2.11 Finisher Stapler Move Motor......................................................................
REP 16.2.12 Finisher Stapler Assembly .........................................................................
REP 16.2.13 Compiler Tray Assembly............................................................................
REP 16.2.14 Folder Knife Assembly ...............................................................................
REP 16.2.15 Stacker Elevator Motor ..............................................................................
REP 16.2.16 Stacker Tray ..............................................................................................
REP 16.2.18 Eject Belt....................................................................................................
REP 16.2.19 Eject Motor Assembly ................................................................................
REP 16.2.21 Finisher PWB.............................................................................................
REP 16.2.22 Finisher LVPS............................................................................................
REP 16.2.23 Eject Motor.................................................................................................
REP 16.2.24 Front/Rear Tamper Motor ..........................................................................
REP 16.2.25 Front/Rear Tamper Home Sensors ...........................................................
REP 16.2.26 Compiler No Paper Sensor........................................................................
REP 16.2.27 Front/Rear Carriage Assembly ..................................................................
REP 16.3.1 Booklet PWB................................................................................................
REP 16.3.2 Booklet Maker Assembly .............................................................................
REP 16.3.3 Booklet Front Cover .....................................................................................
REP 16.3.4 Booklet Rear Cover .....................................................................................
REP 16.3.5 Booklet Top Cover .......................................................................................
REP 16.3.6 Booklet PWB Cover .....................................................................................
REP 16.3.7 Booklet Left Cover .......................................................................................
REP 16.3.8 Booklet Front/Rear Stapler ..........................................................................
REP 16.3.9 Booklet Stapler Move Motor ........................................................................
22. A Finisher
REP 22.1 Intergrated Office Finisher ..............................................................................
REP 22.3.1 Paddle Belt ..................................................................................................
REP 22.3.2 Sub Paddle Solenoid ...................................................................................
REP 22.4.1 Exit Roll Assembly .......................................................................................
REP 22.4.2 Staple Assembly ..........................................................................................
REP 22.4.3 Set Clamp Home Sensor .............................................................................
REP 22.4.4 Exit Roll Assembly .......................................................................................
REP 22.5.1 Pinch Roll.....................................................................................................
REP 22.5.2 Finisher Entrance Sensor ............................................................................
REP 22.5.3 Compile Exit Sensor ....................................................................................
REP 22.5.4 Main Paddle Shaft Assembly.......................................................................
REP 22.5.5 Lower Chute Assembly................................................................................
REP 22.6.1 ENT Roll Assembly......................................................................................
REP 22.6.2 Upper Chute Assembly................................................................................
Repairs and Adjustments
service-repair-manual.com
y
4-145 REP 22.8.2 Stacker Shaft Assembly...............................................................................
4-146 REP 22.8.3 Stacker Motor...............................................................................................
4-147 REP 22.8.4 Stacker Stack Sensor ..................................................................................
4-147 REP 22.9.1 Compile Assembly .......................................................................................
4-148 REP 22.9.2 Set Clamp Shaft...........................................................................................
4-151 REP 22.9.3 Eject Belts ....................................................................................................
4-151 REP 22.9.4 Eject/Set Clamp Motor Assembly ................................................................
4-152 REP 22.9.5 Rear Tamper Home Sensor.........................................................................
4-152 REP 22.9.6 Eject Shaft Assembly ...................................................................................
4-153 REP 22.10.1 Front/Rear Tamper Motor Assembly..........................................................
4-153 REP 22.10.2 Front Tamper Home Sensor ......................................................................
4-155 REP 22.10.3 Eject Clamp Home Sensor.........................................................................
4-156 REP 22.10.4 Stack Height Sensor ..................................................................................
4-166
7. HCF
4-167
ADJ 7.1.2 HCF Side Edge Registration ..........................................................................
4-167
4-168
9. Electrical Components
4-168
ADJ 9.1.1 IOT Lead Edge/Side Edge Registration .........................................................
4-169
ADJ 9.2.1 Edge Erase Value Adjustment........................................................................
4-169
ADJ 9.3.1 Firmware Version Downloading......................................................................
4-170
11. IIT
4-170
4-171
ADJ 11.1.1 IIT Lead Edge/Side Edge Registration .........................................................
4-171
ADJ 11.2.1 Reduce/Enlarge Adjustment.........................................................................
4-172
ADJ 11.6.1 Full/Half Rate Carriage Position Adjustment ................................................
4-173
15. DADF
4-174
ADJ 15.1.1 DADF Side Edge Registration ......................................................................
4-176
ADJ 15.1.3 DADF Non-Standard Sized Original Customized Registration Function ......
4-177
ADJ 15.1.4 DADF Lead Edge Registration .....................................................................
4-179
ADJ 15.1.5 DADF Height Adjustment .............................................................................
4-179
ADJ 15.1.6 DADF Position (Skew) Adjustment...............................................................
4-180
4-180
4-182
4-185
4-187
4-189
4-191
4-193
4-194
4-196
4-198
4-198
4-200
4-201
4-203
4-206
4-208
June, 2008
4-2
.......................................................................
y .......................................................................
WorkCentre 5222, 5225, 5230
4-209
4-210
4-211
4-214
4-216
4-216
4-218
4-220
4-221
4-223
4-225
4-226
4-228
4-229
4-231
4-233
4-235
4-237
4-238
4-239
4-240
4-241
4-245
4-246
4-247
4-249
4-250
Revision