Related Manuals for Toro TimeCutter Z 79166
Summary of Contents for Toro TimeCutter Z 79166
- Page 1 Form No. 3353-493 Rev A 48in Vac-Bagger TimeCutter Z Riding Mower Attachment Model No. 79166—Serial No. 250000001 and Up Operator’s Manual Original Instructions (EN) Register your product at www.Toro.com...
-
Page 2: Table Of Contents
Whenever you need service, genuine Toro parts, or precautions. additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and This manual uses two other words to highlight serial numbers of your product ready. Figure 1 illustrates Important information. -
Page 3: Safety
Safety Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-7320 1. Crushing hazard of hand—do not remove the whole bagger from the machine; open the bagger top and then remove the bag(s) from the bagger. -
Page 4: Installation
Installation Note: Determine the left and right sides of the machine from the normal operating position. Note: The installation of this attachment requires the information found in the Operator’s Manual; you should have the manual at hand to reference during the installation. Loose Parts Note: Use the chart below to identify parts used for assembly. -
Page 5: Preparing The Mower
Qty. Discharge tube Grass bags Installing the bagger assembly Bagger top assembly Registration card Fill out and return to Toro. Read before operating the machine and Operator’s manual vac-bagger. Preparing the Mower Installing the Grass Baffle Install the 48 inch grass baffle to the existing grass baffle... -
Page 6: Installing The Blower Assembly
Installing the Blower Assembly Installing the Blower Pivot Support 1. Slide the pivot support over the threaded stud welded Installing the Blower Pulley to the front of the mower near the discharge opening. Use the inside slot on the pivot support so that the 1. -
Page 7: Pulley
Installing the Blower Important You may have to lift the blower slightly for the latch to close. Ensure that the latch operates smoothly 1. Install the mower to the machine; refer to Operator’s and closes completely. Manual. 2. Install the blower by lowering the pivot pin into the pivot support (Fig. -
Page 8: Assemble The Bagger
Assemble the Bagger 3. Mount the blower belt cover using two 1/4 x 5/8 inch bolts and two 1/4 inch locknuts (Fig. 10). Tighten the locknuts slightly so light drag is felt on the belt cover If necessary, install the bagger frame to the cover. Attach when it is tilted upward. -
Page 9: Preparing The Machine
Preparing the Machine Installing the Bagger Support Assembly Attach the bagger support assembly to the machine frame Installing the Weight with four bolts (3/8 x 1 inch), four washers (3/8 inch), and four locknuts (3/8 inch) as shown in Figure 14. Caution The bagger adds a lot of weight to the rear of the machine and may cause an unstable condition... -
Page 10: Installing The Vac-Bagger Onto The Machine
Installing the Vac-Bagger onto 2. Install the bags by sliding the bag frame hooks onto the retaining brackets (Fig. 16). the Machine Installing the Bagger Assembly 1. Carefully lift the bagger top assembly and slide it onto the bagger support assembly (Fig. 15). The bagger top assembly is easier to install if two people work together. -
Page 11: Removing The Bagger
Mounting the Discharge Tube 2. Carefully lift the bagger top and slide off the quick-attach bracket (Fig. 20). The bagger top 1. Insert the upper end of the discharge tube into the assembly is easier to remove if two people work bagger top. - Page 12 Removing the Belt Covers 1. Remove the blower belt cover by removing two 1/4 inch locknuts and 1/4 x 5/8 inch bolts (Fig. 21). 2 & 3 m–8285 Figure 23 m–8287 1. Idler pulley bracket and 3. “V” side of belt into top Figure 21 pulley pulley groove...
- Page 13 Removing the Blower Pivot Support Note: When nut is removed the shaft is free to drop out of the spindle. Be sure to support the spindle and blade from 1. Remove the pivot support and pivot bracket from the the bottom side. mower (Fig.
- Page 14 3. Align the discharge chute with the holes in the brackets and the spring and spacer in the space between the brackets and above the deflector (Fig. 29). 4. Place the spring and spacer so that the hooked ends of the spring are pointing down, with one end contacting on the mower deck and the other over the deflector (Fig.
-
Page 15: Operation
m–6432 1376 Figure 30 Figure 31 1. Slotted leveling bracket 2. Washer and hairpin cotter 1. Bagger top 2. Bag retainer handles 3. Check the mower level front-to-rear and side-to-side; refer to the Operator’s Manual for instructions. 3. Compress debris into the bags. With both hands, lift up on the bag and unhook it from the retaining bracket (Fig. -
Page 16: Clearing Obstructions From The Bagger
Clearing Obstructions from the remove the filled grass bag and close the top of the liner. Then pull the liner out the grass bag or turn the bag upside Bagger down while holding the handle on the bottom of the grass bag, allowing the liner to slide out. -
Page 17: Maintenance
Bagging Wet Grass Warning Do not mow on slopes when grass is wet. Always try to cut grass when it is dry because your lawn will have a neat You or bystanders could be severely injured by appearance. Wet grass on level surfaces can be mowed flying debris or thrown objects that may pass using the conventional side discharge feature of the through torn, worn, or deteriorated grass bags. -
Page 20: The Toro Total Coverage Guarantee
If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.
Need help?
Do you have a question about the TimeCutter Z 79166 and is the answer not in the manual?
Questions and answers