Omnimount TILT-PA Installation Instructions Manual

Tilting pipe adapter

Advertisement

Quick Links

Step 10 — Adjusting Tilt
B.
To adjust tilt
1. Hold A with 3/4" Socket
2. Loosen B with 3/4" Socket
3. Loosen C with 9/16" Socket
4. Position Display
5. Tighten A,B, & C
Specifications are subject to change without prior notice.
Every effort has been made to provide accurate and error-free assembly and installation. Omni-
Mount Systems disclaims liability for any difficulties arising from the interpretation of information
contained in these instructions. If OmniMount products are used for purposes other than their
original intent, OmniMount, its distributors and retailers shall not be held responsible or liable for
injuries or property damage, direct, indirect, or consequential, which may arise from the inability
to use this product safely, properly, and in the manner for which it has been designed and manufac-
tured. Warranty does not apply to products which have been lost, damaged by misuse, abuse, or
accident.
12
C.
A.
PN —9/05
Installation Instructions
TPUM-1: Tilting Pipe Adapter
Designed for 26" - 55" Flat Panel TV's
Maximum Weight Capacity: 175 lbs. (79.4 Kg)
Connects to 1.5" NPT Pipe

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TILT-PA and is the answer not in the manual?

Questions and answers

Summary of Contents for Omnimount TILT-PA

  • Page 1 If OmniMount products are used for purposes other than their original intent, OmniMount, its distributors and retailers shall not be held responsible or liable for injuries or property damage, direct, indirect, or consequential, which may arise from the inability to use this product safely, properly, and in the manner for which it has been designed and manufac- tured.
  • Page 2 Step 8 — Attaching the Tilt-PA to the Pipe 1. Thread and tighten Tilting Pipe Adapter onto 1.5” NPT Pipe (not included). 2. Tighten Tilt Tension Nut before attaching Adapter. Step 9 — Attaching the Adapter and Display to the Pipe Adapter Note: Pipe removed for clarity 4.
  • Page 3 Step 7 — Attaching the UM1 to the Display Mounting Spacer Screw (if needed) 1. Thread Mounting Screw through Square Washer, Rail, Spacer (if needed), and into the Display’s Mounting Holes. NOTE: Ensure Retaining Screws are loose enough to allow for adjustment 2.
  • Page 4: Parts List

    Parts List Description A Philips Screws M4 x 16mm B Philips Screws M4 x 36mm C Philips Screws M4 x 45mm D Philips Screws M5 x 16mm E Philips Screws M5 x 36mm F Philips Screws M5 x 46mm G Philips Screws M6 x 16mm H Philips Screws M6 x 36mm I Philips Screws M6 x 46mm J Philips Screws M8 x 16mm...
  • Page 5 Step 4 — Rail Installation Narrow Configuration Standard Configuration Step 5 — Secure Sliders and Back Plate 1. Set Rails to horizontal distance between Mounting Holes on Display. 2. Loosely thread Slider Retaining Screws through Channels into Sliders Step 1 — Set Studs in UM-1 1.
  • Page 6 Step 2 — Determine Rail Selection Measure the vertical distance between Mounting Holes on Display. If distance is greater than 19” (48cm) use the supplied Extended Rails. Extended Rail Installation (only if required) 1. Using the Small Hex Wrench unscrew the Slider Retaining Screws (8).

This manual is also suitable for:

Tpum-1

Table of Contents