Table of Contents
Advertisement
Quick Links
• Sealed, permanently lubricated bearings.
• Cast-iron wheel guards and dust vents.
• One-piece quick adjusting spark guards.
• Large quick adjust eye shields.
• Easy-adjust cast tool rest.
• Safety key switch.
• Fine and coarse vitrified grinding wheels included.
• Rubber foot mounts reduce vibration and prevent sliding.
• Wheel dresser included.
FEATURES
WHEEL SIZE
ARBOR SPEED
ARBOR SIZE
AMPERES
MOTOR
WEIGHT
SPECIFICATIONS
MODEL
MODEL
15-870 M1
15-910 M1
8" x 1" (203 x 25 mm)
10" x 1" (254 x 25 mm)
3450 RPM
1720 RPM
5 ⁄
" (16 mm)
1" (25 mm)
8
9.6 AMP
13.5 AMP
1 HP , 110 V, 1 Ph
1
59 LBS (27 kg)
103 LBS (47 kg)
1 ⁄
HP , 110 V, 1 Ph
2
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for General International 15-870 M1
Summary of Contents for General International 15-870 M1
-
Page 1: Specifications
FEATURES SPECIFICATIONS MODEL MODEL 15-870 M1 15-910 M1 • Sealed, permanently lubricated bearings. • Cast-iron wheel guards and dust vents. • One-piece quick adjusting spark guards. WHEEL SIZE 8” x 1” (203 x 25 mm) 10” x 1” (254 x 25 mm) •... -
Page 2: Safety Rules
20. Do not use this bench grinder for any purpose other while it is unattended. than it’s intended use. If used for other purposes, General International disclaims any real or implied 10. Keep children away. Make sure that visitors are warranty and holds itself harmless for any injury kept at a safe distance from the work area. -
Page 3: Unpacking And Cleanup
HEAVY DUTY BENCH GRINDER 15-870 / 15-910 Thank you for choosing this GENERAL® INTERNATIONAL heavy duty bench grinder. This unit has been carefully tested and inspected before shipment and if properly used and maintained, will provide you with years of reliable service. To ensure optimum performance and trouble free operation a reasonable amount of care and attention is required. -
Page 4: Grounding Methods
GROUNDING METHODS Fig. 1 Fig. 2 Fig. 3 The use of an extension cord is not recommended, if necessary use a three-prong extension cord and outlet, if the exten- sion will be used outside the cord must be suitable for outdoor use (immediately replace the extension cord if worn out, cut or damaged). - Page 5 REPLACING GRINDING WHEELS Fig. 6 Follow these procedures to remove and replace the grinding wheels. Unplug the grinder from the power source. Raise the eye shield out of the way. Loosen and pull the tool rest out as far as possible. Do not remove completely.
-
Page 6: Parts List
PARTS LIST 15-870 PART N0. DESCRIPTION SIZE QTY PART N0. DESCRIPTION SIZE QTY 15870-01 SHAFT 15870-36 COPPER WASHER 15870-02 ROTOR 15870-37 TOOTH WASHER 15870-03 STATOR 15870-38 SWITCH 15870-04 COPPER WIRE 15870-39 SWITCH PLATE 15870-05 WIRE 15870-40 CROSS HEAD SCREW W/WASHER 3/16"... - Page 7 15 870...
- Page 8 PARTS LIST 15-910 PART N0. DESCRIPTION SIZE QTY PART N0. DESCRIPTION SIZE QTY 15910-01 SHAFT 15910-38 COPPER WASHER 15910-02 ROTOR 15910-39 TOOTH WASHER 15910-03 STATOR 15910-40 SWITCH 15910-04 COPPER WIRE 15910-41 SWITCH PLATE 15910-05 WIRE 15910-42 CROSS HEAD SCREW W/WASHER 3/16"...
- Page 9 15 910...
- Page 10 15-870 / 15-910 8360, Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3 Tel.: (514) 326-1161 Fax: (514) 326-5565 Parts and Service Fax: (514) 326-5555 Order desk orderdesk@general.ca www.general.ca IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity desired.
Need help?
Do you have a question about the 15-870 M1 and is the answer not in the manual?
Questions and answers