Mircom BPS-602 Installation Manual
Mircom BPS-602 Installation Manual

Mircom BPS-602 Installation Manual

Nac power extender

Advertisement

Quick Links

BPS-602
NAC Power Extender

Installation Guide

(see Application Guide for additional information)
Rev. 042209

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BPS-602 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Mircom BPS-602

  • Page 1: Installation Guide

    BPS-602 NAC Power Extender Installation Guide (see Application Guide for additional information) Rev. 042209...
  • Page 2: Specifications

    BPS-602 - NAC Power Extender Overview: The Mircom BPS-602 is an extremely cost effective 6.5 amp remote power supply/battery charger. It may be connected to any 24 volt Fire Alarm Control Panel (FACP). Primary applications include Notification Appliance Circuit (NAC such as strobes and horns) expansion support to meet ADA requirements.
  • Page 3: Power Supply Specifications

    Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all local codes and authorities having jurisdiction. Product is intended for indoor dry use only. ground Carefully review: Application Guide for BPS-602, BPS-802, BPS-1002 Power Supply Specifications (pg. 3) Stand-by Specifications (pg. 3)
  • Page 4 (horns) to be silenced while visual notification appliances (strobes) continue to operate. The FACP must be capable of a visual annunciation to the silencing status of the output or zone(s) to which the BPS-602 (NAC Power Extender) is connected. Sync Mode Selection Table:...
  • Page 5 *Note: The BPS-602 will only synchronize horns, horn/strobes and strobes that contain synchronization capability. Contact signal manufacturer for more detailed info (see Appendix A.4, pg. 12). The same synchronization mode must be selected for all outputs Amount of Notification Appliances per NAC:...
  • Page 6: Led Diagnostics

    The green input LEDs will be off (normal condition). To reset the memory depress the reset button (Fig. 2c, pg. 7). The LED(s) will extinguish. Note: If indicating circuits have been restored, memory reset is not required for normal operation of the unit. - 6 - BPS-602...
  • Page 7: Hookup Diagram

    C "DRY1" NC UPPER TERMINALS RET1+ RET1-- RET2+ RET2-- C "DRY2" NC LOWER TERMINALS Power Limited Outputs 2.5 amp per Addressable output in alarm Control Module Power (total=10 amp) Trigger Output sion Relay See Note 2 upplied) BPS-602 - 7 -...
  • Page 8: Maintenance

    Fuses: Check input fuse on the power supply board, replace if necessary. Input fuse rating is 5 amp @ 250V. Note: Maximum charging current is 650mA. Note: Expected battery life is 5 years; however, it is recommended changing batteries in 4 years or less if needed. - 8 - BPS-602...
  • Page 9: Battery Calculation Worksheet

    Current per number of devices. Stand-by: 90mA 90mA BPS-602 (Current draw from battery) Alarm: 175mA 175mA BPS-602 Current 90mA 175mA Auxiliary Devices Refer to device manual for current ratings. Alarm/Stand-by Alarm/Stand-by Alarm/Stand-by Auxiliary Devices Current (must not exceed 1 amp) Refer to device manual for current ratings.
  • Page 10: Appendix A - Ul Listed Compatible Devices

    Appendix A - UL Listed Compatible Devices A.1 Four (4) Wire Smoke Detectors Table A-1 below lists four (4) wire smoke detectors compatible with BPS-602 AUX output. Max Standby Alarm Smoke Detector/Base Detector Type Current (mA) Current (mA) FenWal CPD-7021 (w/70-201000-005 Base) Ionization 0.10...
  • Page 11 System Sensor 6424 Projected Beam 28.4 System Sensor Beam 1224(S) Projected Beam 38.5 * Contact manufacturer for current draws A.2 Door Holders Table A-2 below lists door holders compatible with BPS-602 AUX output. Manufacturer Model Type Current (mA) Edwards DH150A Floor Mount...
  • Page 12 A.4 Strobes Table A-4 below lists strobes compatible with BPS-602 NAC output. Wheelock Devices: Sychronizing Horns AH-12 AH-12WP AH-24AH-24 HS-24 AH-24WP NH-12/24 MIZ-24S Sychronizing Horn Strobes AS-121575W HS4-24MCWH AS-24100C AS-24MCW HS4-24185W NS-121575W AS-24MCWH ZNS-MCW NS-2-41575W AS-2415C ZNS-MCWH NS-24MCW AS-2475C HS4-24150C...
  • Page 13 System Sensor Devices: Wall Horn/Strobes P2RH P4RH P2RK P4RK P2RHK P4RHK P2WH P4WH Wall Strobes SRHK Ceiling Horn/Strobes PC2R PC4R PC2RH PC4RH PC2RK PC4RK PC2RHK PC4RHK PC2W PC4W PC2WH PC4WH Ceiling Strobes SCRHK SCRH SCRK SCWH Horns BPS-602 - 13 -...
  • Page 14 AS-MC-W SET-S17-CW-WP ZR-HMC-CW AS-HMC-R SET-MC-CW ZBB-R AS-HMC-W SET-MC-CR ZBB-W AS-MC-CR SET-HMC-CW MTH-R AS-MC-CW SET-HMC-CR MTH-W AS-HMC-CR SET-177-CR-WP MTH-MC-R AS-HMC-CW SET-177-CW-WP MTH-MC-W AS-75-R-WP SET-185-R-WP MTH-75-R-WP AS-75-CR-WP SET-185-W-WP MTH-15-115-R-WP AH-R SEF-MC-R MTH-HMC-CR-WP AH-W SEF-MC-W MTH-HMC-R-WP AH-WP SEF-HMC-R MTH-HMC-W-WP - 14 - BPS-602...
  • Page 15 Notes: BPS-602 - 15 -...
  • Page 16: Enclosure Dimensions

    (38.1mm) (117.22mm) (117.22mm) (38.1mm) Mircom is not responsible for any typographical errors USA - 4575 Witmer Industrial Estates, Niagara Falls, NY 14305, Canada - 25 Interchange Way, Vaughan (Toronto), ON L4K5W3, 888-660-4655 • fax: 888-660-4113 web site: www.mircom.com IIBPS-602 K23O...

Table of Contents