Subscribe to Our Youtube Channel
Related Manuals for Beretta 20050692
Summary of Contents for Beretta 20050692
- Page 1 ROGRAMMABLE THERMOSTAT Installation and user instruction This instructions to be retained by the user...
- Page 2 This programmer can be used either as a maximum switching load of 2A at 30VDC central heating ON/OFF thermostat and or 0,25A at 230VAC or with Beretta as boiler remote control (only with boilers fitting a bus protocol connection selected Beretta boilers), therefore is...
- Page 3 Type Description Your programmer is a room thermostat Room thermostat working with (recognized by no house icon on display) ON/OFF command to the boiler. – type crt Connect the 2 right wires (highlighted with T.A.) room thermostat Your programmer is a boiler remote connection on the boiler.
- Page 4 Programming Fast room button temperature adjusting buttons Fast DHW adjusting buttons (rEc only) Heating mode button...
- Page 5 Adjusting buttons Display Heating mode button Temperature Battery flap sensor...
- Page 6 recommended that this device is installed NSTALLATION AND OPERATING INSTRUCTIONS Unlike the conventional thermostat, this by a qualified electrician. control separates the function in two ACKING LIST units. The receiver serves for wiring RF receiver with 6 wires fitted connections and heat on/off control. The RF transmitter transmitter serves as the user interface Anchors and screws...
- Page 7 Important: Secure the receiver wiring harness to the internal boiler cable anchors Important: never connect contact to 230V supply to avoid the destruction of the bus circuit. NSTALLATION OF RECEIVER Secure the receiver in the proximity of the Blue = main supply 230 Vac = neutral N boiler using 2 anchors (see picture below Brown = main supply 230 Vac = line L for drill holes specifications) and screws...
- Page 8 reason should the receiver box be there is not necessity to make any opened. The appliance can only be encoding operation after installation (both mounted indoors and in areas free from installation type) - follow the encoding any water or moisture. Wiring must instruction communication conform to IEE regulations.
- Page 9 ARNING board of the transmitter as it contains electrostatically sensitive components. UNCTIONS The Beretta Programmable 7-day RF Thermostat has the following functions: Type Room thermostat (crt): for the display appearance in this mode, please In the case of using anchors, the...
- Page 10 with the set point, switches ON or OFF Programming timing: it is possible by the heating request (according the selecting the relative timing fascia to programmed timing). The temperature select the desired time. The programming sensor is located on the left side of the is possible during 7 day 24-hours and the item.
- Page 11 room temperature. In AUTO mode it is midnight. After the counter down is ended possible increase decrease the programmer switch to AUTO mode. temporary the room set temperature by PARTY mode automatically switch pressing the buttons, only if programmer comfort the current time is inside in a heating ON temperature (T1).
- Page 12 values not just an ON/OFF) according to the 4 status OFF – AUTO – PARTY - the calculation made. With this type of HOLIDAY. communication it is possible also to OFF mode, the heating request to adjust by remote the domestic hot water the boiler is off, on display there is not (DHW) temperature...
- Page 13 set (T1) is maintained only inside the (T2). number days timing fascia. The next heating fascia will considered on the day starting from back original midnight. After the counter down is ended temperature. It is possible to check the the programmer switch to AUTO mode. target flow temperature communicated to PARTY mode automatically switch boiler...
- Page 14 the scrolling give access to the following PERATING INSTRUCTIONS settings: The programmer is factory set as room Attention: the TYPE of the device (that is thermostat type (crt). Most part of the main menu selection) should parameters are already set, at the start have already been set by the installer as up it is necessary to set the time and the this set is according the installation made...
- Page 15 icon Description Factory set T1 = 21° C Setting the comfort (T1) and economy (T2) temperatures T2 = 16° C Setting the time Unset Setting the day Unset Setting the programming fascia Unset Setting the domestic hot water temperature (only rEc type) 42°...
- Page 16 Set the target domestic hot water. minutes. Use the button to enter and exit. Use the to increase or Set the day of the week. Use decrease the value. Use the button to increase or decrease. to enter and exit. tyPE Set the device installation type.
- Page 17 menu is set ON. Set the programming be shown in the main display, together fascia in the same way used for heating with the spanner icon. In most of the fascia. The setting is possible daily, not weekly. The heating of the DHW tank will cases it is sufficient to press the done according...
- Page 18 is no communication between receiver and boiler. Or receiver connected on the LIMATIC CURVES room thermostat (T.A.) boiler connection. Below climatic curves A99 = too many resets. There have been programmer. Curves from 0,2 to 0,8 are more than 5 resets in 15 minutes. used when the boiler is set for low Following this alarm, it is necessary to temperature (i.e.
- Page 19 External temperature icon means that there is a heat request from the room to the boiler. The DISPLAY IN crt (ON/OFF) MODE: boiler will switch ON. When the device is in its standard mode of functioning, the appearance of the central heating symbol and bar display will be the following: is a proportional indication of the set-point...
- Page 20 temperature display day icon and the night icon indicates actual temperature indicate whether the current set point for measured inside the room the current time is night or day. time display indicates the party icon is lit up when the actual time party mode is selected.
- Page 21 When the icon appears, the controller icon means that the device is set is working as to keep the anti-frost as a wireless device, and that the temperature. communication is effective DISPLAY (remote control) icon means that there is a heat MODE: request from the room to the boiler.
- Page 22 fascia set for the central heating set point setting. If a bar is completely blank, the temperature display set-point is the anti-frost level (central indicates actual temperature heating OFF). If only the lower part of a measured inside the room bar is black, the set point is the economy (T2).
- Page 23 controller to the installation. Following party icon is lit up when the instructions are dedicated to expert party mode is selected. In this mode the personnel as they have a deep impact on central heating fascia will the working mode of your boiler and your completely lit up at T1 together with the system.
- Page 24 Par. Factory Descr. Type Operation Ref. set value Display shows the wireless channel and the address. Use button to start the encoding procedure. On the Type Encoding receiver press for 5 second the button up to the codified procedure orange light is flashing, the transmitter start to codify all the and crt values and the display shows P00..-P90.
- Page 25 Par. Factory Descr. Type Operation Ref. set value Use the button to decrease and the button to Climatic Type (see increase the climatic curve value (see below the climatic curve climatic curves). The value is automatically memorized when selection only curves) moving to the next parameter.
- Page 26 Par. Factory Descr. Type Operation Ref. set value Type Software This parameter just shows the software reference number Actual release on the device and crt Use either the button and the button to switch to °F Type or ° C. all the temperatures values will change. In case of Choice °...
- Page 27 Par. Factory Descr. Type Operation Ref. set value Type Alarms Use the and the button to scroll last 9 alarms code Actual history memorized on the device. only Type Boiler TSP Actual Unused reading only Anti- Type Use the and the button to switch ON or OFF the Legionella legionella function (function active only with boiler...
- Page 28 Room sensor: -10° C ÷ 40° C installation conditions electromagnetic environment). ECEIVER Linked with transmitter Beretta -Via Risorgimento 23/A frequency 868 MHz Power rating: 230 VAC ± 10%, 50 Hz 23900 Lecco (Italy) www.berettaclima.com T.A. Switching capacity (crt only): − Min 1mA, Beretta...
Need help?
Do you have a question about the 20050692 and is the answer not in the manual?
Questions and answers