Focus Adjustment - JVC AV-21W83 Service Manual

522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
AV-21W83
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
AV-21W93
AV-21W93B
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
ADJUSTMENTS
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
B1 POWER SUPPLY
Measuring
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
Item
instrument
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25 Signal
Check of
Generator
B1 POWER
SUPPLY
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
DC Voltmeter
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25

FOCUS ADJUSTMENT

Measuring
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
Item
instrument
Adjustment
Signal
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
of FOCUS
generator
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
IF CIRCUIT ADJUSTMENTS
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
Measuring
Item
instrument
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
Adjustment
Remote
of VCO (CW)
control unit
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
Adjustment Remote
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
of DELAY control unit
POINT
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
(AGC
TAKE-OVER)
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
Setting
(Adjustment time)
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
DELAY POINT
(AGC TAKE-OVER)
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
522 tu2522 tu2522 tu2522 tu2522 tu2522 tu2522 tu25
18
Test point Adjustment part
B1 (pin 1)
GND (pin 5)
[CN00S
connector
in MAIN
PWB]
Test point Adjustment part
FOCUS VR
[In HVT]
Test point Adjustment part
VCO (CW)
VCO (CW) . MHz
TOO HIGH
ABOVE REFERENCE
YELLOW
BELOW REFERENCE
TOO LOW
DISPLAY : EXIT
DELAY POINT
Initial setting value
26
1. Receive a black and white signal.
2. Connect a DC voltmeter between B1 and GND
(between pin 1 and 5 of the connector CN00S).
3. Make sure that the voltage is DC135 ± 1.5V.
Notes:
• Set PICTURE MODE (VSM) to "BRIGHT".
• The final adjustment of CONVERGENCE must be done after the
FOCUS adjustment. (CONVERGENCE is changed by FOCUS ad-
justment.)
When makes difference by FOCUS adjustment, should be reconfirming
PURITY adjustment.
1. Receive a cross-hatch signal.
2. While looking at the screen centre, adjust the FOCUS VR so that
the vertical and horizontal lines will be clear and in fine detail.
3. Make sure that the picture is in focus even when the screen gets
darkened.
Note:
• Under normal conditions, no adjustment is required.
1. Select 1. IF from the SERVICE MENU.
2. Select 1. VCO by pressing the 1 key on the remote control unit.
fv
3. Receive a broadcast signal.
4. Check the characters colour of the BELOW REFERENCE displayed
to yellow.
5. Press the DISPLAY key three times to return to normal screen.
1. Receive a black and white broadcast signal (colour off).
2. Select 1. IF from the SERVICE MENU.
3. Select 2. DELAY POINT by pressing the 2 key on the remote con-
trol unit.
4. Adjust the MENU */T key in order to eliminate any noise or beat
from the image. Any increase above the initial value produces noise
and any decrease below it produces beat.
5. Press the DISPLAY key three times to return to the normal screen.
6. Turn to other channels and make sure that there are no irregulari-
ties.
No. 52016
Description
Description
Description