QuanSheng TG-45UV User Manual page 33

FUNCTION OPERATION AND DESCRIPTION（The following description is without
voice prompt.）
overtime warning" in DTMF side tone after clicking "option box" and "Edit" in PC program software.
Single call/Group call/Troop call in channel mode
1. If you want to make single call/group call/troop call in channel mode, please select Menu 27 to store channel (details
please refer to page 36) or set all the above parameters in PC programming and write them into radios, corresponding
to the above a, b, c, d to realize function after finish the above A and B operation steps accordingly.
Automatic Control of Single Call/Group call/Troop call
It mean you can activate these function only by selecting the signal code and pressing PTT key, no
need to use sending code.
Operating steps:
1. ANI code can be set by PC programming only, you can input user-defined code in " ID CODE" frame after click
"DTMF" and "Edit" in toolbar. (Details please refer to Menu 15 in page 30) Note: The ANI code of each radio is
independent.
For example: 1st sub-radio: 10026 2nd sub-radio: 10088 3rd sub-radio: 22233 4th sub-radio: 88888
2. There is " troop call code" in option box and choose code "A" (troop call code is universal character of ANI code),
finally write into radio. (Troop call code can be ABCD*#)
3. Steps to set 15 groups of signal code: please click "Edit" in toolbar and click "DTMF", then input the AI code of
1st sub-radio, 2nd sub-radio and 3rd sub-radio to the corresponding 1, 2, 3 code group in DTMF frame, then input
group code "100AA" to four groups and input troop code "AAAAA" to the five groups (Note: The signal code
corresponds to DTMF code in PC software is in Menu 17, details please refer to page 31), finally write into the radio
after edit.
Code Group Sending Code
1 10026
2 10088
3 22233
4 100AA
5 AAAAA
6
For example: 7
FUNCTION OPERATION AND DESCRIPTION 55
FUNCTION OPERATION AND DESCRIPTION（The following description is without
voice prompt.）
4. Parameters setting: select Menu 19, then open PTT-ID and set the delay time of code sending (Details please refer
to page 33) and confirm it; select Menu 33, then open DTMF (Details please refer to page 40) and confirm it; select
Menu 34 to set the silent mode and select QT+DT (Details please refer to page 41) and confirm it, finally the setting
is finished.
5. If you want to make a single call to 1st sub-radio: in Menu 17 "signal code" (Details please refer to page 31) and
select first group (Note: The signal code corresponds to DTMF code in PC software) and confirm it; press PTT key
of main radio to transmit the own PTT-ID and adverse PTT-ID, the single call is activated successfully. If you want to
call signal code of 2nd sub-radio and 3rd sub-radio please select corresponding second and third group.
6. If you want to make a group call to 1st sub-radio and 2nd sub-radio: in Menu 17 "signal code" (Details please refer
to page 31) and select the fourth group (Note: The signal code corresponds to DTMF code in PC software) and
confirm it; press PTT key of main radio to transmit the own PTT-ID and group call code, the group call is activated
successfully.
7. If you want to make a troop call: in Menu 17 "signal code" (Details please refer to page 31) and select the fifth
group (Note: The signal code corresponds to DTMF code in PC software) and confirm it; press PTT key of main radio
to transmit the own PTT-ID and troop call code, the troop call is activated successfully.
8. You should press PTT key of any sub-radio to send the confirm message to main radio after the single call/group
call/troop call is activated, finally all the radios can work with each other. If the activate time is 5s, it mean you should
resend the code to activate it when the radio standby more than 5s.You can set up the activate time in frame "1-15s
launch overtime warning" in DTMF side tone after clicking "option box" and "Edit" in PC program software.
56 FUNCTION OPERATION AND DESCRIPTION
NOTE
!
⊙
The function is only valid when
PTT-ID is open.