Sony CDX-M800 Installation/Connections page 4

Precautions
• Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
• Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
• Use only the supplied mounting hardware for
a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 60°.
Removing the bracket (4)
Before installing the unit, remove the
bracket 1 from the unit.
1
Insert both release keys 7 together between
the unit and the bracket until they click.
1
2
Pull down the bracket , then pull up the
1
unit to separate.
Extended portion of the front
panel (5)
Mounting example (6)
Installation in the dashboard
When installing this unit, be sure to close the
front panel of the unit. (6- )
*
If the front panel is opened while installing and
given too much force, it may cause a
malfunction.
Notes
• Bend these claws outwards for a tight fit, if
necessary. (6-2)
• Make sure that the 4 catches on the protection
collar 5 are properly engaged in the slots of the
unit. (6-3)
Mounting the unit in a Japanese
car (7)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 4.
Warning when installing in a car
without ACC (accessory) position
on the ignition key switch
After tuning off the ignition, be sure to
press and hold (OFF) on the unit until the
clock display disppears.
Otherwise, the display does not turn off and this
causes battery drain.
RESET button (8)
When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc.
使用前注意事項
•請仔細選擇安裝位置，以使本機不妨礙正常的
駕駛操作。
•避免將本機安裝在多塵、髒亂、極易受震動的
地方，或者高溫之處，如陽光直射處或暖氣機
前。
•為了安全和安裝牢固，安裝時請使用附送的安
裝部件。
安裝角度之調整
請在 60 度以內調整安裝角度。
拆下保護環（4）
安裝之前，請先從本裝置上拆下托架 1 。
1
將兩把開鎖鑰匙 一起插入裝置和托架
7
間，直至聽到喀嗒聲。
2
向下拉托架 1 ，然後向上拉裝置，使之相互脫
離。
前面板的伸出部分（5）
安裝示例（6）
安裝在儀錶板裡
6-
安裝時必須關閉前面板。（ ）
*
安裝時若前面板開著，以及施以太大的力，都會
造成故障。
註
• 若有必要，則可彎曲這些卡爪使配合
緊密。 （6-2）
• 必須將保護環 5 上的 4 個鉤爪正確嚙合在裝置的卡
槽中。 （6-3）
將本機安裝於日本產汽車上時
（7）
有的日本產汽車不能安裝本機，在這種情形下，
請您向當地的 Sony 經銷商諮詢。
註
為防止發生故障，安裝時只能使用附送的螺絲 4 。
安裝在點火鑰匙開關上沒有 ACC
（附件）位置的汽車上時的警告
關閉汽車發動機後，必須按住 (OFF) 不
放，直至顯示消失。
否則顯示不會關閉，並耗費電池。
之
1
RESET 按鈕（8）
當安裝和連接完成後，必須用原子筆等按壓
RESET 按鈕。