Laser Pegs MPS 400 HELICOPTER Instructions

Please read this manual before
MPS 400
you begin! Failure to follow this
manual's instructions may result in
HELICOPTER
damage to the Mobile Power Source
and/or Laser Pegs®. Not adhering
For Boys And Girls
to these instructions will void
Ages 5 And Up
the manufacturer's warranty. The
4 Models+ packaging must be kept because it
contains important information.
Any creation you can build
WARNING:
LIGHTED
CHOKING HAZARD
Not for children under 3 yrs.
CONSTRUCTION SET INCLUDES:
Do not submerge in water.
• 2 Laser Pegs®
Warning:
• 45 Construction Parts
This product contains a
button battery. If swallowed, it could cause
• Mobile Power Source
severe injury or death in just 2 hours. Seek
• Instruction Manual
medical attention immediately. "
Batteries
WARNING: STROBE LIGHTS
Included
MAY CAUSE SEIZURES
EN71, RoHS COMPLIANT
This product complies to all safety
requirements of ASTM F 963
MODEL INSTRUCTIONS
All additional model instructions can be
downloaded at www.LaserPegs.com
Laser Pegs® Parts List
x1
x2
Laser Pegs ® Stackable
Laser Pegs ® link that allows you to
STACKABLE
connect to other construction kits.
Construction Parts List
x3
x1
x6
x5
x6
x2
x2
x1
x1
x2
www.LaserPegs.com
This manual is copyright and cannot be reproduced or used online without Laser
Pegs®Ventures LLC permission. Copyright 2013 © All Rights Reserved US Patent
#7,731,558 Additional Global & Multiple Patents Pending. Laser Pegs® Ventures
LLC. 8304 Consumer Ct., Sarasota FL. 34240. Contact: Support@LaserPegs.com
Connecting Pegs
Connecting Pegs
To construct with Laser Pegs®, slide two
pieces together to form a connection.
To construct with Laser Pegs®, slide two pieces together to form a
Slide each piece on and off smoothly.
connection. Slide each piece on and off smoothly.
Slide Power Switch
Press button to
to turn on/off/flash
turn on/off/flash
Power Switch
Slide Power Switch to cycle
Push button to cycle through different
-
Small parts.
light settings.
through different
light settings.
Power Switch
Battery
Compartment
Peg Holes
*To avoid short-circuits, keep metal objects and other
unauthorized materials from obstructing the peg holes.
Remove the three Philips
Please dispose of batteries properly as per state and local regulations.
Battery head screws with a 4mm
section
Replacing Batteries
1. Remove the Phillips head screw. Peg Holes
2. Remove the Battery Compartment Cover.
3. Place three LR 44 batteries in the correct position.
(Batteries are to be inserted with the correct polarity).
Power 4. Replace the Battery Compartment Cover.
5. Replace the Phillips head screw.
Switch
6. Slide Power Switch to turn on!
7. Do not mix old and new batteries.
Push switch to
8. Do not mix alkaline, standard (carbon-zinc), or
ON/OFF/FLASH
rechargeable (nickel-cadmium, NiMH) batteries!
9. Exhausted batteries are to be removed from the power
*To avoid short-circuits, keep metal objects and other base.
10. Never connect more than 4 Laser Pegs®
un-authorized materials from obstructing the peg holes.
11. Non-rechargeable batteries are not to be recharged.
12. Rechargeable batteries are only to be recharged under
When Using Batteries
adult supervision.
1. Remove screws.
13. Rechargeable batteries are to be removed from the toy
2. Place three LR 44 batteries in the correct
before being recharged.
position - as displayed inside the Mobile Power Source.
14. The supply terminals are not to be short-circuited.
3. Push Power Switch to turn on!
15. DO NOT THROW BATTERIES INTO FIRE!
4. Do not mix old and new batteries.
5. Do not mix alkaline, standard (carbon- Screw Battery
zinc), or rechargeable (nickel-cadmium) batteries! Compartment Cover
6. Exhausted batteries are to be removed
Remove the Phillips head
from the power base.
7. Never connect more than 4 Laser Pegs®
8. Non-rechargeable batteries are not to be recharged.
x2
9. Rechargeable batteries are only to be charged under
adult supervision.
10. Rechargeable batteries are to be removed from the
x4 Batteries
toy before being charged.
11. Batteries are to be inserted with the correct polarity.
x2
12. The supply terminals are not to be short-circuited.
LR 44
Button Cell
WARNING! Each Laser Peg® draws current from the batteries. Therefore,
x2
Battery x3
the more pegs you use, the quicker you will deplete your battery power! As
Mobile Power Source
the power weakens, the current will slowly fail and some Laser Pegs® will
illuminate (typically the reds and yellows) and some won't. When the Laser
WARNING! Each Laser Peg® draws current from the batteries. Therefore,
x6
Pegs® dim the Laser Pegs® are not broken, they just need stronger batteries.
the more pegs you use, the quicker you will deplete your battery power! As
You have 3 simple options...
the power weakens, the current will slowly fail and some Laser Pegs® will
1. Change the batteries.
illuminate (typically the reds and yellows) and some won't. When the Laser
2. Use high quality batteries. They will last a little longer, but they will still
Pegs® dim, the Laser Pegs® are not broken, they just need stronger batteries.
deplete rapidly the more Laser Pegs® you connect!
You have 3 simple options...
1. Change the batteries.
2. Use high quality batteries. They will last a little longer, but they will still
deplete rapidly the more Laser Pegs® you connect!
RESCUE HELICOPTER: Incredibly fast chopper designed for
mountain and water rescue missions.
RESCUE HELICOPTER
Construction Compatible
Model
Difficulty
Level
Remove Pull
STEP
Tab To Activate
1
Batteries
STEP
screw driver.
2
Requires
3 LR 44 Button Cell
Batteries
STEP
3
screw with a 4mm screw
driver.
STEP
4
Requires
3 LR 44 Button Cell
Batteries
STEP
5
A
STEP
6
STEP
7
STEP
8
COMBINE
A