Please read this manual before you begin!
C1200
Failure to follow this manual's instructions may
result in damage to the 3D Lite Board®, AC
Adapter and/or Laser Pegs®. Not adhering to
HELICOPTER
these instructions will void the manufacturer's
warranty. The packaging must be kept because
AGES 5+
it contains important information.
30 Models+
WARNING:
CHOKING HAZARD
-
Small parts.
Any creation you can build
Not for children under 3 yrs.
LIGHTED
Do not submerge in water.
CONSTRUCTION SET INCLUDES:
®
• 36 Laser Pegs
• 169 Construction parts
• Triangle Power Base
• Instruction Manual
Requires 3 AA Batteries
Batteries NOT
EN71, RoHS COMPLIANT
Included
This product complies to
all safety requirements
of ASTM F 963
Laser Pegs® Parts List
x2
x5
x2
x2
x2
x2
Y PEG
x8
45° PEG
SQUARE
STRAIGHT
STRAIGHT
M-M PEG
T-PEG
TRUSS PEG
STRAIGHT
x2
SQUARE
M-M PEG
PEG
Color
Each Laser Peg® is color coded on the circuit board inside
each shape.
Code
Warning:
This product contains a
button battery. If swallowed, it could cause
severe injury or death in just 2 hours. Seek
medical attention immediately.
Sound Activated
Triangle Power Base
Construction Parts List
x9
x2
x30
x8
x4
x8
x15
x8
x4
x1
x15
x4
x7
x2
x4
x2
x4
www.LaserPegs.com
This manual is copyright and cannot be reproduced or used online without Laser
Pegs®Ventures LLC permission. Copyright 2014 © All Rights Reserved US Patent
#7,731,558 Additional Global & Multiple Patents Pending. Laser Pegs®Ventures
LLC. 8304 Consumer Ct Sarasota FL. 34240. Contact: Support@LaserPegs.com
Connecting Pegs
To construct with Laser Pegs®, slide two pieces together to form a
connection. Slide each piece on and off smoothly. To build away from the
Triangle Power Base, use the peg cord in one of the top three peg holes to
illuminate your model! The 90° pegs are essential to construction but they
DO NOT ILLUMINATE.
Environmental Phenomena
* The unit may malfunction if subjected to radio-frequency interference. It SHOULD revert to
normal operation when the interference stops. If not, it may become necessary to turn the power
off and back on, or remove and reinstall the batteries.
* In the unlikely event of an electrostatic discharge, the unit may malfunction and lose memory,
requiring the user to reset the devise by removing and reinstalling the batteries.
Push Red
Red
Power Button
Power Button
to turn on/off
Push Red Power Button to
cycle through 4 different
light settings.
AC Adapter
SOUND/ON/FLASH/FLASH FASTER
Connection
WARNING: STROBE LIGHTS
The toy is not to be connected to more than
MAY CAUSE SEIZURES
the recommended number of power supplies
x7
Replacing Batteries
Stackable
1. Remove the three (3) screws.
2. Place three (3) AA batteries in the correct
x4
position - as displayed inside the Triangle
Power Base.
3. Reassemble the Triangle Power Base.
4. Replace the three (3) screws.
WHEEL PEG
5. Push RED Power Button to turn on!
6. Do not mix old and new batteries.
7. Do not mix alkaline, standard (carbon-
zinc), or rechargeable (nickel-cadmium,
NiMH) batteries!
8. Exhausted batteries are to be removed
from the Triangle Power Base.
9. Never connect more than 200 Laser Pegs®
10. Non-rechargeable batteries are not to be
recharged.
11. Rechargeable batteries are only to be
recharged under adult supervision.
12. Rechargeable batteries are to be removed
from the toy before being recharged.
13. Batteries are to be inserted with the
correct polarity.
14. The supply terminals are not to be short-
circuited.
15. DO NOT THROW BATTERIES INTO FIRE!
Please dispose of batteries properly as per state and local regulations.
Using an
AC Adapt
er
Remove all batteries
from Laser Pegs® power
x6
base before using the
x14
5-volt AC adapter.
*To avoid short-circuits, keep metal objects and
x6
other unauthorized materials from obstructing
the peg holes.
x3
The AC adapter and the Triangle Power Base are to be regularly examined for
damage to the cord, plug, enclosure and other parts, and in the event of such
damage, they must not be used until the damage has been repaired.
x11
x2
WARNING! Each Laser Peg® draws current from the batteries. Therefore, the more
pegs you use, the quicker you will deplete your battery power! As the power
weakens, the current will slowly fail and some Laser Pegs® will illuminate (typically
the reds and yellows) and some won't. When the Laser Pegs® dim the Laser Pegs®
are not broken, they just need stronger batteries or an AC Adapter.
You have 3 simple options...
1. Use a 5-volt AC Adapter –available from www.LaserPegs.com
2. Change the batteries.
3. Use high quality batteries. They will last a little longer, but they will still deplete
rapidly the more laser pegs you connect!
DO NOT SUBMERGE IN WATER
ASSAULT HELICOPTER: Although primarily used for warfare, this powerful aircraft is
also used for fighting something else...forest fires.
ASSAULT HELICOPTER
Model
Difficulty
Level
5
Peg Holes
A
STEP
1
Try-Me function contains
3xL1154F/LR44
Add 3-AA Batteries
3-AA Batteries
STEP
2
Remove LR-44 Batteries
The LR-44 batteries are only for the
"Try-Me" function, they should be re-
moved from the Triangle Power Base
and replaced with 3 - "AA" batteries
before giving it to the child.
Requires (3AA) Batteries
STEP
When using an AC
3
Adapter, NEVER
place the adapter
plug into the Tri-
angle Power Base
top peg holes.
Never connect more than 200
Laser Pegs® when using a 5-volt
(2000mA) AC Adapter.
COMBINE
PARTS
STEP
4
STEP
5
STEP
6
STEP
7
FLIP MODEL
ROTATE
OVER
MODEL
Need help?
Do you have a question about the C1200 HELICOPTER AGES 5+ and is the answer not in the manual?
Questions and answers