Laser Pegs MPS 300B Quick Start Manual

Please read this manual before
MPS 300B
you begin! Failure to follow this
manual's instructions may result in
Sprint Car
damage to the Mobile Power Source
and/or Laser Pegs®. Not adhering
Series
to these instructions will void
AGES 5+
the manufacturer's warranty. The
packaging must be kept because it
4 Models+
contains important information.
Any creation you can build
WARNING:
LIGHTED
CHOKING HAZARD
Not for children under 3 yrs.
CONSTRUCTION SET INCLUDES:
Do not submerge in water.
• 2 Laser Pegs
®
• 49 Construction Parts Warning:
This product contains a
• Mobile Power Source
button battery. If swallowed, it could cause
severe injury or death in just 2 hours. Seek
• Instruction Manual
medical attention immediately. "

Batteries

WARNING: STROBE LIGHTS
Included
MAY CAUSE SEIZURES
EN71, RoHS COMPLIANT
This product complies to all safety
requirements of ASTM F 963
Laser Pegs ® Parts List
x2
STACKABLE MOBILE POWER SOURCE
The toy is not to be connected to more than
the recommended number of power supplies

Construction Parts List

x6
x6
x4
x6 x6
x3
x2
x7
x1
x2
MADE IN CHINA
www.LaserPegs.com
This manual is copyright and cannot be reproduced or used online without Laser
Pegs®Ventures LLC permission. Copyright 2014 © All Rights Reserved US Patent
#7,731,558 Additional Global & Multiple Patents Pending. Laser Pegs® Ventures
LLC. 8304 Consumer Ct., Sarasota FL. 34240. Contact: Support@LaserPegs.com

Connecting Pegs

Connecting Pegs
To construct with Laser Pegs®, slide two
To construct with Laser Pegs®, slide two pieces together to form a
pieces together to form a connection.
connection. Slide each piece on and off smoothly. Slide each piece on and off smoothly.
Press button to
Slide Power Switch
turn on/off/flash
to turn on/off/flash
Power Switch
Slide Power Switch to cycle
Push button to cycle
through different
through different
-
Small parts.
light settings.
light settings.
Power Switch
Battery
Compartment
Peg Holes
*To avoid short-circuits, keep metal objects and other
unauthorized materials from obstructing the peg holes.
Battery
Please dispose of batteries properly as per state and local regulations.
section

Replacing Batteries

Peg Holes
1. Remove the Phillips head screw.
2. Remove the Battery Compartment Cover.
3. Place three LR 44 batteries in the correct position.
(Batteries are to be inserted with the correct polarity).
Power
4. Replace the Battery Compartment Cover.
Switch
5. Replace the Phillips head screw.
6. Slide Power Switch to turn on!
Push switch to
7. Do not mix old and new batteries.
8. Do not mix alkaline, standard (carbon-zinc), or
ON/OFF/FLASH
rechargeable (nickel-cadmium, NiMH) batteries!
9. Exhausted batteries are to be removed from the power
*To avoid short-circuits, keep metal objects and other
base.
un-authorized materials from obstructing the peg holes.
x1
10. Never connect more than 4 Laser Pegs®
11. Non-rechargeable batteries are not to be recharged.
When Using Batteries
12. Rechargeable batteries are only to be recharged under
adult supervision.
13. Rechargeable batteries are to be removed from the toy
before being recharged.
14. The supply terminals are not to be short-circuited.
15. DO NOT THROW BATTERIES INTO FIRE!
Screw Battery
x4
Compartment Cover
Batteries
LR 44
WARNING! Each Laser Peg® draws current from the batteries. Therefore,
x2
Button Cell
the more pegs you use, the quicker you will deplete your battery power! As
Battery x3
Mobile Power Source the power weakens, the current will slowly fail and some Laser Pegs® will
illuminate (typically the reds and yellows) and some won't. When the Laser
Pegs® dim the Laser Pegs® are not broken, they just need stronger batteries.
WARNING! Each Laser Peg® draws current from the batteries. Therefore,
You have 3 simple options...
the more pegs you use, the quicker you will deplete your battery power! As
1. Change the batteries.
the power weakens, the current will slowly fail and some Laser Pegs® will
2. Use high quality batteries. They will last a little longer, but they will still
illuminate (typically the reds and yellows) and some won't. When the Laser
deplete rapidly the more Laser Pegs® you connect!
Pegs® dim, the Laser Pegs® are not broken, they just need stronger batteries.
You have 2 simple options...
1. Change the batteries.
2. Use high quality batteries. They will last a little longer, but they will still
deplete rapidly the more Laser Pegs® you connect!
Sprint Car: High-powered race cars designed primarily for the pur-
TRANSATMOSPHERIC FIGHTER - A spacecraft capable of flight within
pose of running on short oval or circular dirt or paved tracks.
the atmosphere, similar to an airplane.
SPRINT CAR
Construction Compatible
Model
Difficulty
Level
A
Remove Pull
Tab To Activate
STEP
Batteries
1
STEP
2
Remove the three Philips
head screws with a 4mm
screw driver.
Requires
3 LR 44 Button Cell
B
Batteries
STEP
3
STEP
4
Remove the Phillips head
screw with a 4mm screw
STEP
driver.
5
Requires
3 LR 44 Button Cell
Batteries
COMBINE FLIP MODEL
PARTS OVER
STEP
7
STEP
8
STEP
9
STEP
10
STEP
STEP
11
6
ROTATE
MODEL