TABLE OF CONTENTS TABLE OF CONTENTS ... 2 GENERAL INFORMATION... 3 FFL 50 F ANTASEA LASH FLASH HOUSING D ENERAL GENERAL SPECIFICATIONS ... 3 FEATURES AND ACCESSORIES INCLUDED WITH THE HOUSING ... 4 ... 5 UNCTION ONTROLS MAINTENANCE OF THE MAIN GASKET SEAL ... 6 MOUNTING THE SPEEDLIGHT IN THE HOUSING ...
Housing for the Olympus E330. Does not include 5 pin Nikonos type sync cord. GENERAL FLASH HOUSING DESCRIPTION The Fantasea FFL 50 is rated to a maximum working depth of 60m/200 ft. It is an injection molded plastic housing, constructed to take the rigorous environments that underwater photographers and outdoor photographers experience, and will protect the Olympus FL50 Speedlight in these demanding activities.
FEATURES AND ACCESSORIES INCLUDED WITH THE HOUSING FEATURES: • Visible main gasket seal for final pre-dive check • Double O-ring design on all controls • Bulkhead and hotshoe plug for external TTL strobe ACCESSORIES INCLUDED: • Spare main gasket seal •...
FUNCTION CONTROLS 1. Mode To select the flash control mode and is shown on the control panel. 2. Zoom This is to adjust the firing angle. 3. Test Dual purpose for Auto Check and Test flash activation. 4. Power Power button for Off and On. 5.
MAINTENANCE OF THE MAIN GASKET SEAL Each housing is individually inspected and hydrostatically tested in the factory. The design of the main gasket seal is among the most reliable in the industry and the watertight integrity is excellent. This special gasket design provides a perfect seal even if there is any movement between the body and lid due to change of ambient pressure.
Page 7
When to Maintain the Gasket Seal: Remove the gasket periodically for inspection. It is not necessary to remove, clean and re-install the gasket after every dive provided the gasket did not become contaminated. The flash housing may be required to be opened between dives, to recharge the batteries.
Page 8
Clean the seal recess (the square groove where the gasket sits) with a cotton bud. Inspect the gasket all the way round its surface for damage such as cuts tears or contamination. This should be done visually and also by feeling the surface texture between finger and thumb.
Page 9
EXCLUSIVE PRESSURE RELEASE PLUG The body and lid are uniquely designed with a "no clip" closure arrangement. Our testing has shown that this arrangement allows the water to exert an even pressure on the O-ring, thus increasing the reliability of the watertight seal.
Page 10
OPENING LEVERS After unscrewing and pulling out the pressure release plug, the lid can be opened. To overcome the friction of opening, two levers are used to push against the lid with a cam action. On some models these opening levers are bolted to the body.
MOUNTING THE SPEEDLIGHT IN THE HOUSING INSERTING Since the Fantasea FFL 50 Flash Housing was specifically designed for the Olympus FL50 Speedlight, insertion is a simple matter of placing the flash into the housing. Make sure the flash is properly aligned and that it sits perfectly flat.
CLOSE HOUSING 1. Place housing back over front and align the complete mating surface of the housing and the gasket, forming a proper seal. 2. Ensure that the pressure release plug is pulled all the way out while closing, otherwise the air cannot escape.
ATTACHING THE SYNC CORD The sync cord is a 5 pin Nikonos type sync cord. The sync cord connects the flash to the camera housing. Both ends of the cord are identical so either side can be inserted into the flash and camera housings. When you insert the cord into the port you must exercise caution—the pins inside the cord are delicate and must not be damaged.
ATTACHING FLASH HOUSING TO ARM You can either use the Fantasea Flex or Ball and Joint Arms to attach the flash housing to the camera housing. Other arm systems can be used and Fantasea offers adapters to make this possible. Please check with Fantasea or your dealer regarding compatibility issues.
It is always wise to have backup batteries in case you do run out of power. The Ni Cad batteries can be recharged many times and offer an economical and environmentally friendly alternative to one-use disposable batteries. Check the users manual of the Olympus FL50 Speedlight for confirmation of compatibility with other batteries.
TRAVELING When transporting by air, please ensure the housing is not sealed to allow the air pressure to equalize; removing the gasket is recommended. Please protect the housing during transportation by wrapping it in foam or other protective wrapping. ACCIDENTS The impact resistance of the housing is excellent.
WARRANTY FANTASEA HOUSINGS ONE YEAR CONSUMER LIMITED WARRANTY In order to receive warranty service register your Fantasea Housing you must present your proof of purchase, indicating the date on which the purchase was made. This product is warranted by Fantasea Line to be free from defects in materials and workmanship for a period of one year from the date of purchase.