Related Manuals for BON ELECTRONICS BSM-093N3G
Summary of Contents for BON ELECTRONICS BSM-093N3G
- Page 1 BSM-093N3G / BSM-173N3G BSM-183N3G / BSM-213N3G BSM-243N3G / BSM-463N3G BSM-553N3G BSM-212i / BSM-242i...
-
Page 2: Table Of Contents
Contents Safety Instructions........................3 Front............................4 Rear.............................6 MENU Description........................8 VIDEO............................9 DISPLAY 1..........................10 DISPLAY 2..........................12 COLOR.............................14 MARKER..........................15 OSD............................17 OSD 2............................19 AUDIO............................20 GPI............................22 SYSTEM...........................24 USB Firmware Update......................26 External Remote Control......................27 Assignable functions are listed below..................28 Dimensions..........................29 Troubleshooting........................30 Warranty Information........................32 Modification of Product......................32 Caution on Menu Operation......................32 Caution for Monitor Placement....................32 Caution for Usage........................32... -
Page 3: Safety Instructions
Safety Instructions To help avoid damaging your monitor, connect only one power (AC or DC) in operation. Rough handling of product may cause physical damage or malfunction. Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock. -
Page 4: Front
Front [BSM-18.5 ~ 24” Front Key] ” [BSM-9 Front Key] ” [BSM-46” 55” Front Key]... - Page 5 ) Power 2) Menu 3) Enter 4) SDI 1, SDI 2 Input 5) HDMI/DVI Input 6) Analog Switch analog input in the order of CVBS1 -> CVBS2 -> CVBS3 -> SVIDEO -> YPbPr -> RGB -> VGA. 7) WF/VS Waveform / Vectorscope display selection button. 8) Marker On/Off 9) Scan Switch scan mode among Zero Scan, Under Scan, Over Scan, Pixel to Pixel in HD...
-
Page 6: Rear
Rear ① ⑦ ⑧ ② ⑥ ③ ④ ⑤ ⑩ ⑪ ⑫ ⑨ 1,2) SDI Port 3) Component YPbPr/RGB or CVBS 1,2,3 Port 4) HDMI Port 5) DVI-I Port 6) Loop-Through Out for SDI-1/SDI-2 or YPbPr 7) AC Input Please check Power Cord, Power Voltage, Supply power for power input are suitable for the standard before use. - Page 7 8) DC Input For DC power supply. Check the DC Input voltage. In case of using the Battery power, DC 12 ~ 24V is usable. 9) Update Port The Serial communication terminal that for changing the operating program(Firmware) of the body or controlling the monitor. 10) Remote Ethernet Port External control via PC is able with this port by using 'Wall Control Program'.
-
Page 8: Menu Description
MENU Description General Cautions for OSD menu or Display The menu may not be displayed even when user pressed Menu button if there's No Signal, or in unclear signal status. The menu selection may be saved for each input signal mode, so sometimes user should do menu selection again. -
Page 9: Video
VIDEO Brightness, Contrast, Chroma, Phase, Sharpness Adjust color representation values. SDI 3G Mode Turns on SDI 3G mode to accept 3G signal. SDI Switching Normal : Use Normal in general condition but the screen might be blinking on screen change when you use Matrix or Routing Switcher. Fast : Use Fast to minimize blinking on screen change. -
Page 10: Display 1
DISPLAY 1 Aspect Set the aspect ratio of the screen. 16:9, 4:3, Native(Original) are selectable. 1:1 Scan Set this on to display picture in 1:1 pixel mapping. Anamorphic Set this mode to resize the screen to 3.56:1, 2.74:1, 2.59:1, 2.55:1, 2.40:1, 2.39:1, 2.35:1, 1.85:1, 1.75:1, 1.66:1, or 1.37:1 Waveform Display Select waveform display mode. - Page 11 Timecode Display On/Off Timecode Position Set the position of timecode. Timecode Size Set the size of time code among small, medium, large.
-
Page 12: Display 2
DISPLAY 2 Exposure Range Check (Video Range Check) Checks Y, C level and displays over-exposed or under-exposed area on screen. The base value can be Y, Cb, or Cr. Y Range Max / Min Set Y range value for range check. C Range Max / Min Set C range value for range check. - Page 13 DISPLAY2 - FOCUS ASSIST Focus Assist Display Turns on Focus Assist mode. This mode can be set also by pressing Focus Assist button in front. Focus Assist Box Select the size of the focus assist box. Focus Assist Level The sensitivity of the focus assist function can be set between 0 to 48. Focus Assist Color Set brush color of focus assist mode among Blue, Green, and Red.
-
Page 14: Color
COLOR Dithering Turn this mode on to view motion pictures smoothely when the source has low quality. Color Temperature Select color temperature among 3200K, 5600K, 6500K, 9300K or USER. (Gain and Offset menu are displayed on USER temperature only) Red/Green/Blue Gain (USER mode only) R,G,B gains are adjustable on User mode. -
Page 15: Marker
MARKER Marker Ratio Select one of preset markers or user marker. To display marker, press Marker button in front of the monitor. Center Marker Set preference to display center marker or not. Safety Area 16:9 Adjust size of the safety area when marker displayed on 16:9 screen. Safety Area 4:3 Adjust size of the safety area when marker displayed on 4:3 screen. - Page 16 User Marker H1 / User Marker H2 / User Marker V1 / User Marker V2 Set user marker’s position. H1 for left, H2 for right, V1 for top, V2 for bottom. The positions are saved as the selected marker name such as USER1.
-
Page 17: Osd
OSD Display Time Set menu display time (seconds) MENU Position Set menu position among Left Top, Right Top, Left Bottom, Right Bottom and Center. V-Chip SD-SDI, Composite signal might contain V-Chip data. Turn this mode on to display V-Chip information on screen. Closed Caption Select one of 608 Line 21, 608 VANC, 608 Transcoded, 708 to display Closed Captions. - Page 18 Internal Pattern Show internal test pattern such as color bars. Turn this mode off to display general pictures from input port. IMD/UMD Display Display IMD/UMD status. The screen aspect ratio will turn to 16:9 on this mode. IMD/UMD Color Set IMD/UMD color. IMD/UMD Edit Edit IMD/UMD text.
-
Page 19: Osd 2
OSD 2 PIP Source Select Picture-in-Picture source. * You can only use a combination of PIP Mode Digital Signal (Main) + Analog signals (Sub). PIP Mode Large PIP, Small PIP, Side by Side can be selected. PIP Position Sets sub-picture position. Main SDI 1 SDI 2... -
Page 20: Audio
AUDIO Embedded Audio Left Select audio channel for left (Ch 1 ~ 15) Embedded Audio Right Select audio channel for right (Ch 2 ~ 16) Audio Level Meter Turns on/off audio level meters. Level Meter Size Select the size of the meters : Small or Large. Level Meter Position Select the position of the meters : Upper or Lower. - Page 21 Speaker Volume Set volume of speaker. Audio Phase Meter Display Displays audio phase. Level Meter SDI Channel Select audio channel in SDI. Peak Hold Decay Time Adjust the decay time of the peak position. Level Meter Type Select Pair or Group.
-
Page 22: Gpi
GPI Control Turns on/off external monitor control function. GPI Port 1,2,3,4,5,6 Assigns each GPI port’s function. (e.g. SDI 1 input, HDMI input, Tally Red) See EXTERNAL REMOTE CONTROLLING section for details. Remote ID Number Assigns the ID for the monitor to control through serial port. 0 to 99 can be assigned. - Page 23 one. If you use a single monitor to control, you can leave it unchanged. MAC Address This address is unique address for each network device. User does not need to change it.
-
Page 24: System
SYSTEM Function 1,2,3,4 Assigns a function to each function button. See FRONT section for detail. Backlight Set the backlight intensity from 0 to 80. An LCD panel requires more than 30 minutes to be settled to a new backlight value. Front Button LED Set front LEDs on/off status. - Page 25 Firmware Version This version number is required when you request for service. Operating Time This indicates total hours that the monitor operated.
-
Page 26: Usb Firmware Update
Error Message when USB access Message when file on USB or file not exist detected You can also use Serial Port and your PC to update the firmware. Please request for help to your local dealer or directly to BON Electronics. -
Page 27: External Remote Control
External Remote Control Connecting GPI Port(RJ-45) Update Port (RJ-11) Update (RJ-11) Update Terminal Assignment 1 PIN NC 4 PIN 2 PIN RX+ 5 PIN 3 PIN RX- 6 PIN * Turn power off first and connect update cable when you update monitor firmware. -
Page 28: Function Name
Function Name Description Switches the input to SDI-1 SDI-1 Input Switches the input to SDI-2 SDI-2 Input Switches the input to HDMI HDMI Input Switches the input to YPbPr YPbPr Input Switches the input to CVBS-1 CVBS-1 Input Switches the input to CVBS-2 CVBS-2 Input Switches the input to CVBS-3 CVBS-3 Input... -
Page 29: Dimensions
Dimensions BSM-093N3G 223 x 174 x 50.2 mm (8.7 x 6.8 x 1.9 inches) BSM-173N3G 411 x 299 x 62mm (16.1 x 11.7 x 2.4 inches) BSM-183N3G 438.4 x 310.8 x 66.4mm (17.2 x 12.2 x 2.6 inches) BSM-212i 503.6 x348.0 x 70.3mm (19.8 x 13.7 x 2.76 inches) -
Page 30: Troubleshooting
Troubleshooting Try these if you have trouble in using the monitor. Call for Service if you can't solve the problem even after you tried these solutions. Symptom Solution Check Connectivity of Power Cable between Outlet and the Monitor. Press and Hold Power button for more than one second. Power isn't turned on Try with Other Monitor or Electric Device using the same Power Cable. - Page 31 Make Monitor "Factory Default" and Try again. Select Test Pattern(Internal Pattern) in the menu and See if R,G,B Color is Correct. the Startup Logo Color was ok but Check the Input Selection. Strange Color on Active Screen Try with Different Cable. Check if Each Cable is correctly Connected when you use Component as Input.
-
Page 32: Warranty Information
Warranty Information Free Service If the product needs to be repaired in 12 months from the purchase. Exceptions damage caused by accident, abuse, misuse, water, flood, fire, or other acts of nature or external causes damage caused by service performed by anyone who is not an authorized service provider ... - Page 33 Corporate Headquarters Tresebelle-Sky 2F, 1479 Gayang-2, Gangseo-gu, Seoul, South Korea Research / Service Center Vision Tower 7F, 1481 Gayang-2, Gangseo-gu, Seoul, South Korea Telephone +82 2 2659 0333 +82 2 2659 8133 http://www.bon-electronics.com Email salesbon@bon-electronics.com Ver. 16.0 3 . 08...