NEC PlasmaSync 42XM5 PX-42XM5G User Manual page 35

Information
AUTO ID settings
ON: Enables Auto ID function. In the case shown below,
display 1 will be set as ID 1, display 2 as ID2, etc.
This can be set only when a 2 2, 3 3, 1 5 or 5 1
is selected.
REMOTE
IN
REMOTE
OUT
OFF: Disables Auto ID function.
Note: To use this function, you have to connect the
displays with the remote cable (not supplied).
IMAGE ADJUST
The position of the image can be adjusted and flickering
of the image can be corrected.
Example: Adjusting the vertical position
On "VIDEO WALL" menu, select "IMAGE ADJUST", then
press the MENU/ENTER button.
The "IMAGE ADJUST" screen appears.
On "V-POSITION" of "IMAGE ADJUST" menu, adjust the
position.
IMAGE ADJUST
ASPECT MODE :
V-POSITION
H-POSITION
V-HEIGHT
H-WIDTH
AUTO PICTURE :
FINE PICTURE
PICTURE ADJ.
UNDERSCAN :
SEL. ADJ.
Information
IMAGE ADJUST settings
These are the same functions as the IMAGE ADJUST
menu on page En-23.
P. ON DELAY (Power on delay)
Use this function to activate power-on delay.
Turn on the AUTO ID before the following operations.
Example: Setting "ON"
On "P. ON DELAY" of "VIDEO WALL" menu, select
"ON".
DIVIDER
POSITION
DISP. MODE
AUTO ID
IMAGE ADJUST
P. ON DELAY
PLE LINK
SEL.
Information
P. ON DELAY settings
(Video wall modes other than 4 4 and 5 5)
ON: Turns on the main power of each display after a
delay time.
* Once this function has been set to "ON", POWER ON/
OFF button on the remote control does not function
except for the No.1 monitor.
By pressing the POWER ON button on the remote
Downloaded From TV-Manual.com Manuals
REMOTE
OUT
No.1 No.2
No.1 No.2
No.4 No.3
No.4 No.3
REMOTE
IN
Display 1 Display 2
REMOTE
OUT
No.1 No.2 No.1 No.2
No.4 No.3
No.4 No.3
REMOTE
IN
Display 4 Display 3
NORMAL
: ± 0
: ± 0
: 0
: 0
OFF
: 0
: 0
OFF
V-POSITION
EXIT RETURN
VIDEO WALL
: 1
: SPLIT
: OFF
: ON
: OFF
ADJ. EXIT RETURN
control the No.1 monitor will turn on and the others
will be turned on one by one automatically.
* From the second monitor onward, neither the POWER
button on the unit nor the POWER ON button on the
remote control works. However, by pressing and holding
the POWER ON button for more than 3 seconds, the
monitor will be turned on.
OFF: Turns on the main power of all displays at the
REMOTE
same time.
OUT
(Only for 4 4 and 5 5 video wall modes)
MODE1: Turns on the main power of each display
delayed.
REMOTE
MODE2: Turns on the main power of each display more
IN
delayed.
OFF: Turns on the main power of all displays at the
same time.
Note: To use this function, you have to connect the
displays with the remote cable (not supplied).
PLE LINK
Use this function to set a uniform brightness for each display.
Turn on the AUTO ID and set the DIVIDER (at 1, 2 2,
3 3, 1 5 or 5 1) before the following operations.
Example: Setting "ON"
On "PLE LINK" of "VIDEO WALL" menu, select "ON",
then press the MENU/ENTER button.
: + 6 4
Information
PLE LINK settings
ON: Sets a uniform brightness for each screen in a video
wall. This can be set only when a 1, 2 2, 3 3, 1 5
or 5 1 video wall is selected.
OFF: Sets the individual screen brightness for each
screen in a video wall.
* When this function is set "ON", connect your plasma
displays with the remote cable (optional) in the order of
the position numbers for the 2 2 video wall. See the
drawing below.
* If there are changes in the DIVIDER or POSITION,
the PLE LINK will automatically turn OFF.
REMOTE
REMOTE
* With the 3 3, 1 5 or 5 1 video wall, connect the
final display to the first display the same way as with
2 2 video wall.
Note:
* The remote control can be operated unless the IR
REMOTE is set to "OFF".
* To use this function, you have to connect the displays
with the remote cable (not supplied).
En-34
VIDEO WALL
DIVIDER : 1
POSITION
DISP. MODE : SPLIT
AUTO ID : OFF
IMAGE ADJUST
P. ON DELAY : OFF
PLE LINK : ON
SEL. ADJ. RETURN
EXIT
REMOTE
OUT
No.1 No.2
No.1 No.2
No.4
IN No.4 No.3
REMOTE
IN
Display 1 Display 2
REMOTE
OUT
No.1 No.2
No.1 No.2
OUT
No.4
No.4 No.3
REMOTE
IN
Display 4 Display 3
REMOTE
No.3 OUT
REMOTE
No.3
IN