Instruction Manual - AEG MC 4403 CD Instruction Manual & Guarantee

General safety instructions
To avoid the risk of fi re or an electric shock, you should
not expose the device to rain or moisture. Consequently,
do not use the device in the immediate vicinity of water
- for example near a bath tub, a swimming pool or in a
damp cellar.
Use the device only for the intended purpose.
Only connect the device at a properly installed plug
socket. Pay attention that the specifi ed voltage corres-
ponds to the voltage of the plug socket.
When using external mains supply, pay attention to the
correct polarity and voltage. Always place the batteries
in the correct direction.
Assemble the device in such a way that the available
ventilation openings are not covered.
Never open the housing of the device. Incorrect repairs
can constitute a considerable risk for the user. Should
the device become damaged, in particular the mains
supply cable, do not operate the device any longer, but
rather have it repaired by an expert. Check the mains
supply cable regularly for damage.
For safety reasons a broken or damaged mains lead may
only be replaced by an equivalent lead from the manuf-
acturer, our customer service department or a similary
qualifi ed person.
If the device is not used for a longer period, remove the
plug connector from the plug socket or take out the
batteries.
These symbols may be found on the machine and are
intended to indicate the following:
The lightning symbol should advise the user
of parts in the inside of the device which carry
dangerously high voltage levels.
The symbol with an exclamation mark should
advise the user of important operation or
maintenance instructions in the accompa-
nying documentation.
Devices bearing this symbol work with a
„class 1 laser" for tracing the CD. The built-in
safety switches should prevent the user being
exposed to dangerous laser light, which is
invisible to the human eye, when the CD compartment
is opened.
Under no circumstances should these safety switches
be bypassed or manipulated, as this could result in a
danger of exposure to the laser light.
32
5....-05-MC 4403 CD 32
Description of the Controls
1 STANDBY/ON button
2 STANDBY control lamp
3 SENSOR Sensor for the remote control
4 LCD display
5 BBS switch (ON/OFF)
6 VOLUME + / - buttons
7 FUNCTION Function selector (CD/TAPE/TUNER)
8 BAND Band selector switch (FM ST/FM/AM)
9 FM ST control lamp
10 TUNING control
11 CD compartment
12 PUSH/OPEN CD compartment
13 /II CD play/pause button
14 CD Stop button
15 I button (forward search)
16 I button (reverse search)
17 REPEAT button
18 PROGRAM button
19 Cassette compartment
20 door PUSH OPEN
21 II Pause key - cassette
22 / Stop/Eject key - cassette
23 Fast Forward key – cassette
24 Fast Rewind key – cassette
25 Playback key – cassette
26 b Recording key – cassette
Reverse Side
27 FM throw-out aerial
28 PHONES headphone connection
29 Loudspeaker connections
30 AC Mains connection
Remote control
A POWER button
B VOLUME + / - buttons
C I CD button (forward search)
D I CD button (reverse search)
E / II Play/Pause button
F STOP button
G MEMORY button
H REPEAT button
I MUTE button
Start-up of the device/Introduction
• Read the operating instructions thoroughly before the
start-up!
• Remove any transport safety equipment on the CD
and cassette sections.
• Select an appropriate location for the device, e.g. a
dry, fl at, non-slip surface on which the device can be
easily operated.
• Make sure that the device is adequately ventilated!
• Connect the loudspeakers to the back of the music
centre to the sockets market „Speaker R and L" (29).
• Insert the plug into a properly installed 230 V, 50 Hz
power socket. The STANDBY (2) control lamp shows
the function. Please ensure that the mains voltage
corresponds to the information on the type plate.
23.08.2004, 10:35:20 Uhr