3 7 63 1515 0 SERVICE MANUAL CD RECEIVER 49868 2003 KD-SX60WT,KD-SX50M KD-SX60WT K D-SX60WT 180W KD-SX50M K D-SX50M 180W L 13942296513 COMPACT DIGITAL AUDIO Area Suffix J --------- Northern America TABLE OF CONTENTS PRECAUTION............... . . 1-3 SPECIFIC SERVICE INSTRUCTIONS .
Page 2
http://www.xiaoyu163.com 3 7 63 1515 0 SPECIFICATION AUDIO AMPLIFIER Maximum Power Output Front 45 W per channel SECTION Rear 45 W per channel 17 W per channel into 4 Ω, 40 Continuous Power Output (RMS) Front Hz to 20 000 Hz at no more than 0.8% total harmonic distortion.
http://www.xiaoyu163.com 3 7 63 1515 0 SECTION 1 PRECAUTION Safety Precautions Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 4
http://www.xiaoyu163.com 3 7 63 1515 0 Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.2.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.
http://www.xiaoyu163.com 3 7 63 1515 0 SECTION 2 SPECIFIC SERVICE INSTRUCTIONS This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS. L 13942296513 u163 (No.49868)1-5 http://www.xiaoyu163.com...
http://www.xiaoyu163.com 3 7 63 1515 0 SECTION 3 DISASSEMBLY Main body 3.1.1 Removing the front panel assembly (See Fig.1) (1) Press the release button and remove the front panel as- sembly. Front panel assembly Release button Fig.1 3.1.2 Removing the bottom cover (See Figs.2) (1) Turn over the main body and release the two joints a, two joints b and joint c.
Page 7
http://www.xiaoyu163.com 3 7 63 1515 0 3.1.4 Removing the heat sink (See Fig.4) • Prior to performing the following procedure, remove the front panel assembly as required. (1) Remove the two screws B and screw C on the left side of the main body.
http://www.xiaoyu163.com 3 7 63 1515 0 3.1.7 Removing the CD mechanism assembly (See Fig.7) • Prior to performing the following procedure, remove the front panel assembly, bottom cover, front chassis assembly, heat sink, rear bracket and main board. (1) Remove the three screws H attaching the CD mechanism assembly to the top chassis.
Page 9
http://www.xiaoyu163.com 3 7 63 1515 0 CD Mechanism Assembly 3.2.1 Removing the top cover (See Figs.1 and 2) (1) Remove the two screws A on the both side of the body. (2) Lift the front side of the top cover and move the top cover backward to release the two joints a.
http://www.xiaoyu163.com 3 7 63 1515 0 3.2.2 Removing the connector board Wires (See Figs.3 to 5) CAUTION: Before disconnecting the flexible wire from the pickup, solder the short-circuit point on the pickup. No observance of this in- struction may cause damage of the pickup. (1) Remove the screw B fixing the connector board.
Page 11
http://www.xiaoyu163.com 3 7 63 1515 0 3.2.3 Removing the DET switch (See Figs.6 and 7) (1) Extend the two tabs c of the feed sw. holder and pull out the switch. (2) Unsolder the DET switch wire if necessary. DET switch Connector board Pickup...
Page 12
http://www.xiaoyu163.com 3 7 63 1515 0 3.2.4 Removing the chassis unit (See Figs.8 and 9) • Prior to performing the following procedure, remove the top Chassis unit cover and connector board. Suspension spring (L) Suspension spring (R) (1) Remove the two suspension springs (L) and (R) attaching the chassis unit to the frame.
http://www.xiaoyu163.com 3 7 63 1515 0 3.2.5 Removing the clamper assembly (See Figs.10 and 11) • Prior to performing the following procedure, remove the top cover. (1) Remove the clamper arm spring. Clamper arm spring (2) Move the clamper assembly in the direction of the arrow to release the two joints d.
http://www.xiaoyu163.com 3 7 63 1515 0 3.2.6 Removing the loading / feed motor assembly (See Figs.12 and 13) • Prior to performing the following procedure, remove the top cover, connector board and chassis unit. (1) Remove the screw C and move the loading / feed motor assembly in the direction of the arrow to remove it from the chassis rivet assembly.
Page 15
http://www.xiaoyu163.com 3 7 63 1515 0 3.2.7 Removing the pickup unit Pickup unit (See Figs.14 to 18) • Prior to performing the following procedure, remove the top cover, connector board and chassis unit. (1) Remove the screw D and pull out the pu. shaft holder from Part e the pu.
Page 16
http://www.xiaoyu163.com 3 7 63 1515 0 3.2.9 Removing the trigger arm Joint k (See Figs.19 and 20) • Prior to performing the following procedure, remove the top cover, connector board and clamper unit. (1) Turn the trigger arm in the direction of the arrow to release Trigger arm the joint k and pull out upward.
Page 17
http://www.xiaoyu163.com 3 7 63 1515 0 3.2.11 Removing the mode sw. / select lock arm Link plate Joint t (See Figs.22 and 23) Mode sw. • Prior to performing the following procedure, remove the top plate assembly. Select lock arm (1) Bring up the mode sw.
Page 18
http://www.xiaoyu163.com 3 7 63 1515 0 3.2.12 Reassembling the mode sw. / select lock arm Select lock arm spring (See Figs.24 to 26) Hook w REFERENCE: Reverse the above removing procedure. Joint v (1) Reattach the select lock arm spring to the top plate and set Joint v the shorter end of the select lock arm spring to the hook w on the top plate.
Page 19
http://www.xiaoyu163.com 3 7 63 1515 0 3.2.13 Removing the select arm R / link plate Joint c' Link plate Joint r (See Figs.27 and 28) Joint b' Select arm R • Prior to performing the following procedure, remove the top plate assembly.
Page 20
http://www.xiaoyu163.com 3 7 63 1515 0 3.2.15 Removing the loading roller assembly Loading roller assembly (See Figs.31 to 33) • Prior to performing the following procedure, remove the Roller guide clamper assembly and top plate assembly. spring (1) Push inward the loading roller assembly on the gear side and detach it upward from the slot of the joint g' of the lock arm rivet assembly.
Page 21
http://www.xiaoyu163.com 3 7 63 1515 0 3.2.16 Removing the loading gear 5, 6 and 7 Loading gear bracket (See Figs.35 and 36) • Prior to performing the following procedure, remove the top Loading gear 6 cover, chassis unit, pickup unit and top plate assembly. (1) Remove the screw K attaching the loading gear bracket.
Page 22
http://www.xiaoyu163.com 3 7 63 1515 0 3.2.17 Removing the gears Joint p' (See Figs.37 to 40) • Prior to performing the following procedure, remove the top Change plate cover, chassis unit, top plate assembly and pickup unit. rivet assembly • Pull out the loading gear 3. (See Fig.35.) (1) Pull out the feed gear.
Page 23
http://www.xiaoyu163.com 3 7 63 1515 0 3.2.18 Removing the turn table / spindle motor Turn table (See Figs.41 and 42) • Prior to performing the following procedure, remove the top cover, connector board, chassis unit and clamper assembly. (1) Remove the two screws L attaching the spindle motor as- sembly through the slot of the turn table on top of the body.
Exclusive dummy load should be used for AM,and FM. For FM (7) Tracking offset meter dummy load,there is a loss of 6dB between SSG output and (8) Test Disc JVC :CTS-1000 antenna input.The loss of 6dB need not be considered since (9) Extension cable for check direct reading of figures are applied in this working standard.
Page 25
http://www.xiaoyu163.com 3 7 63 1515 0 Maintenance of laser pickup Replacement of laser pickup (1) Cleaning the pick up lens Turn off the power switch and,disconnect the Before you replace the pick up, please try to clean the lens power cord from the ac outlet. with a alcohol soaked cotton swab.
http://www.xiaoyu163.com 3 7 63 1515 0 SECTION 5 TROUBLE SHOOTING Feed section Is the voltage output at Is the wiring for IC521 Is 5V present at IC581 Check CD 9V IC521 pin 40 5V or 0V? (90) (100) correct? pin 6? and 5V.
Page 27
http://www.xiaoyu163.com 3 7 63 1515 0 Tracking section When the disc is rotated at first: Check the circuit in the Check the pickup and vicinity of IC501 pins its connections. 2 12. Approx. 1.2 V Is the tracking error signal output at TP3? Check IC521.
http://www.xiaoyu163.com 3 7 63 1515 0 SECTION 6 DESCRIPTION OF MAJOR ICs HA13164A (IC911) : Regulator • Terminal layout 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 • Block diagram 100u 0.1u BATT.DET OUT ANT OUT Surge Protector 0.1u...
Page 29
http://www.xiaoyu163.com 3 7 63 1515 0 HA17558F (IC571) : Ope. amp. • Pin layout & Block diagram MM74HC126SJ-X (IC691) : 3-state Quad buffer • Pin layout & Block diagram • Truth table INPUT OUTPUT H : High level L : Low level X : Don't care Z : Hi-Z L 13942296513...
Page 30
http://www.xiaoyu163.com 3 7 63 1515 0 TEA6320T-X (IC301) : E.volume • Pin layout OUTRR OUTLR OUTRF OUTLF Vref MUTE CD-CH TAPE TUNER • Block diagram VOLUME 2 MUTE 0 to 55 dB FUNCTION BALANCE ZERO CROSS FENDER REAR POWER DETECTOR SUPPLY VOLUME 1 BASS...
Page 31
http://www.xiaoyu163.com 3 7 63 1515 0 LA4743K (IC941) : Power amp. • Block diagram 2200 F 0.022 F Vcc 1/2 Vcc 3/4 IN 1 OUT 1+ 0.22 F OUT 1- PWR GND1 Protective circuit OUT 2+ IN 2 OUT 2- 0.22 F PWR GND2 L 13942296513...
Page 32
http://www.xiaoyu163.com 3 7 63 1515 0 • Pin layout • Pin function Pin No. Symbol Function Pin No. Symbol Function Header of IC FLIN Front Lch input Power GND RLIN Rear Lch input Outpur(-) for front Rch ONTIME Power on time control STDBY Stand by input Output (+) for rear Lch...
Page 33
http://www.xiaoyu163.com 3 7 63 1515 0 LA6579H-X (IC561) : 4-Channel bridge driver • Pin layout & Block diagram VIN1-A VIN1 VIN1_SW [H]: OP-AMP_A [L]: OP-AMP_B VIN1+A VIN1-B VCCP1 VIN1+B Signal system S-GND power supply VIN1-SW All outputs ON/OFF H : ON VO2+ MUTE MUTE...
Page 34
http://www.xiaoyu163.com 3 7 63 1515 0 • Pin function Pin No. Symbol Function VIN1-A CH1 input AMP_inverted input VIN1+A CH1 input AMP_non-inverted input VCCP1 CH1 and CH2 power stage power supply VO1+ Output pin(+)for channel 1 VO1- CH1 output pin (-) for channel 1 VO2+ Output pin(+)for channel 2 VO2-...
Page 38
http://www.xiaoyu163.com 3 7 63 1515 0 • Pin function Pin No. Symbol Function 3.3V power supply pin Main-beam amp input pin Main-beam amp input pin Sub-beam amp input pin Sub-beam amp input pin Monitor photo diode amp input pin Laser diode amp output pin APC circuit ON/OFF control signal, laser diode (LDO) control signal input or bottom/peak detection frequency change pin.
Page 39
http://www.xiaoyu163.com 3 7 63 1515 0 6.10 TC94A14FA (IC541) : DSP & DAC • Terminal layout & block daiagram Clock generator 1-bit Servo control Digital equalizer Address automatic circuit adjustment circuit Data CLV servo slicer 16 k Synchronous guarantee decoder L 13942296513 Audio out Digital...
Page 40
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol I/O Descroption TMAX O TMAX detection result output pin. TMAX Output TMAX Detection Result Longer than fixed period "PV " Within fixed period "HiZ" Shorter than fixed period "AV " LPFN I Inverted input pin for PLL LPF amp. LPFO O Output pin for PLL LPF amp.
Page 41
6.11 UPD178078GF-622 (IC701) : System CPU • Pin Layout • Pin function Pin No. Symbol Function NO USE OUTPUT L BUS-INT JVC BUS COMMUNICATION LINE BUS-SI J-BUS data input BUS-SO J-BUS data output BUS-SCK J-BUS clock input/output 6 to8 NO USE...
Page 42
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Symbol Function IF COUNT INPUT VDDPLL OSC INPUT FM AM OSC INPUT NO USE GNDPLL AM E.OUT PLL ERROR OUTPUT FOR AM FM E,OUT PLL ERROR OUTPUT FOR FM IC(VPP) SETTING TO WRITE FOR FLASH RESET SYSTEM RESETCD MECHA REMOCON...
Page 44
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY MOBILE ENTERTAINMENT CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.49868) Printed in Japan http://www.xiaoyu163.com...
3 7 63 1515 0 SCHEMATIC DIAGRAMS CD RECEIVER KD-SX60WT,KD-SX50M CD-ROM No.SML200306 KD-SX60WT K D-SX60WT 180W L 13942296513 KD-SX50M 180W K D-SX50M COMPACT DIGITAL AUDIO Area Suffix J --------- Northern America Contents Block diagram Standard schematic diagrams Printed circuit boards...
KD-SX60WT,KD-SX50M 3 7 63 1515 0 Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 47
KD-SX60WT,KD-SX50M 3 7 63 1515 0 < M E M O > L 13942296513 u163 http://www.xiaoyu163.com...
Page 59
KD-SX60WT,KD-SX50M 3 7 63 1515 0 < M E M O > L 13942296513 u163 http://www.xiaoyu163.com...
Page 60
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY MOBILE ENTERTAINMENT CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.49868SCH) http://www.xiaoyu163.com...
3 7 63 1515 0 PARTS LIST [ KD-SX60WT ] [ KD-SX50M ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix J -------------- Northern America L 13942296513 - Contents - 3- 2 Exploded view of general assembly and parts list (Block No.M1)
Page 62
http://www.xiaoyu163.com 3 7 63 1515 0 Exploded view of general assembly and parts list Block No. L 13942296513 u163 http://www.xiaoyu163.com...
Page 63
http://www.xiaoyu163.com 3 7 63 1515 0 General assembly Block No. [M][1][M][M] Symbol No. Part No. Part Name Description Local GE10043-210A TOP CHASSIS GE30942-002A TOP SHEET GE40135-001A EARTH PLATE GE30938-003A SIDE PANEL GE30393-002A BOTTOM COVER FSMA3004-203 INSULATOR QYSDST2604Z SCREW 2.6mm x 4mm(x3) FSKZ4005-001 SCREW (x2)
Page 64
http://www.xiaoyu163.com 3 7 63 1515 0 CD mechanism assembly and parts list Block No. Grease TN-2001-1011 TNG-87 GP-501MK CFD-005Z GP-501A L 13942296513 u163 http://www.xiaoyu163.com...
Page 65
http://www.xiaoyu163.com 3 7 63 1515 0 CD mechanism Block No. [M][B][M][M] Symbol No. Part No. Part Name Description Local 30320101T FRAME 30320102T TOP COVER 30320115T DANPER F 30320116T DANPER R 303205505T CHASSIS RIVET 303205503T CHANGE P. RVT A 303205301T CLAMPER ASS'Y 303205302T SPINDLE MOTOR A 30320502T...
Page 66
http://www.xiaoyu163.com 3 7 63 1515 0 Electrical parts list Main board Block No. [0][1][0][0] Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local NCB31HK-102X C CAPACITOR 1000pF 50V K QEKJ1AM-227Z E CAPACITOR 220uF 10V M IC161 TEA6320T-X NDC31HJ-470X...
Page 67
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C509 QEKJ1AM-107Z E CAPACITOR 100uF 10V M C914 NCB31EK-104X C CAPACITOR 0.1uF 25V K C510 NCB31CK-104X C CAPACITOR 0.1uF 16V K C975 NCB31EK-823X...
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R515 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R732 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R516 NRSA63J-821X MG RESISTOR 820Ω...
Page 69
http://www.xiaoyu163.com 3 7 63 1515 0 Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local D614 LNJ308G81/1-3/X S608 NSW0124-001X TACT SW D615 LNJ308G81/1-3/X S609 NSW0124-001X TACT SW D616 LNJ308G81/1-3/X S610 NSW0124-001X TACT SW D617 LNJ308G81/1-3/X S611...
Page 70
http://www.xiaoyu163.com 3 7 63 1515 0 Packing materials and accessories parts list Block No. A2 A3 A6 A7 L 13942296513 KIT : A8 A9 A10 u163 3-10 http://www.xiaoyu163.com...
Page 71
http://www.xiaoyu163.com 3 7 63 1515 0 Packing and accessories Block No. [M][3][M][M] Symbol No. Part No. Part Name Description Local GET0157-001A INST BOOK ENG FRE SPA GET0157-002A INSTALL MANUAL ENG FRE SPA GET0153-001A CAUTION SHEET LVT0717-001B TROUBLE SHEET(C BT-51018-3 WARRANTY CARD BT-52006-2 WARRANTY CARD BT-51028-2...