CONTENTS Warranty Warranty Power Tools Introduction For full details please visit us at www.909.com Environmental protection Description of symbols Specifications General safety rules Additional safety rules for line trimmers Additional safety rules for the charger Additional safety rules related to the battery pack and battery safety...
Model #: 20VLTG special care to heed the Cautions and Warnings. Voltage: 20Vdc Your 909 power tool has many features that will make No load speed: 10,000 min your job faster and easier. Safety, performance, and Cut diameter (swathe): 250 mm...
General safety rules 3) Personal safety a) Stay alert, watch what you are doing and use WARNING. Read all safety warnings and all instructions. common sense when operating a power tool. Do not Failure to follow the warnings and instructions may result in use a power tool while you are tired or under the electric shock, fire and/or serious injury.
b) Do not use the power tool if the switch does not turn b) Recharge only with the charger specified by the it on and off. Any power tool that cannot be controlled manufacturer. A charger that is suitable for one type with the switch is dangerous and must be repaired.
Do not try to stop the cutting device (nylon line) with your • Additional safety rules for the charger hands. Always let it come to a stop by itself. Your 909 tool with Lithium-Ion batteries may only be • WARNING: After switching off the machine, the cutting charged with the specific designed 909 Lithium-Ion device continues to rotate for a few more seconds.
Page 7
• Do not plug anything other than your 909 battery pack Do not place any object on to, or allow anything to rest •...
Do not dispose of the battery in a fire or put the battery • • Use only the 909 batteries supplied with the 909 Tool or into a microwave oven, conventional oven, dryer, or high- 909-approved replacements. pressure container. Under these conditions, the battery •...
Unpacking When recycling, make it non-conductive by applying • insulating tape to the terminals located on the battery. Due to modern mass production techniques, it is unlikely When to charge the battery that your power tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool New battery packs are shipped in a low charge until the parts have been replaced or the fault has been...
Assembly Adjusting the telescopic handle. The distance between the top handle and the cutting head Assembly of the lower guard is required prior to operation. can be adjusted to suit the comfort of the operator. Prior to carrying out any assembly work, adjustments or maintenance, ensure the battery pack has been removed 1.
Page 12
Adjusting the secondary handle Adjusting the angle of the cutting head. The secondary handle can pivot and lock into 1 of 3 pre-set positions. The angle of the cutting head can be adjusted to suit 1. To change the position of the handle, depress the handle the task being performed.
Important information - product care Note: When the battery of the tool is at the lower end of the charge, the tool is more susceptible to the overload condition. This line trimmer uses Lithium-Ion battery cells. Care As mentioned above, the battery pack is an integral MUST be taken to ensure both the safety and life of the component of this tool and is fitted with thermal safety pack is maintained.
Fitting and removing the battery pack To remove the battery pack from the tool firmly press the battery release button at the back of the battery pack and slide the battery pack backward, and then pull or lift the battery out of the tool handle.
Safety features incorporated with tools using stops the tool from operating (similar to that of the over load condition). When this condition occurs you will need this battery pack to either insert another battery into the tool or recharge the Product overload existing battery.
Switching on and off at an angle of about 30°. Light cuts are better than heavy cuts as they allow the cut grass to fall away from the 1. Insert a charged battery into the handle of the line spool, preventing the grass from clogging the spool. trimmer, ensuring the 4.
Using the protector Handle rotation while edging The trimmer is fitted with a The trimmer has a rotating handle which makes it easier to wire protector. To protect edge while using the handle in an uprigt positon. small plants etc from the 1.
Maintenance and cleaning 3. Remove the empty spool and clean out the spool 1. Store the tool, instruction manual and accessories in cover. a secure, dry place. In this way you will always have 4. Using a fully wound spool, the information ready to hand.
Trouble shooting Problem Solution Line will not feed Check: • Both Lines are correctly routed through Eyelets. • Lines are not crossing each other and lines are in there own spool section • When Bumping, ensure spool is running at full speed. Poor cutting performance Check: •...