Page 3
A092 L2 Service Manual 1. Tools list Tweezer Cross Screw driver III. Solder Tommy bar Hot gun...
Page 4
A092 L2 Service Manual 2. Battery caver disassembly Open the battery cover,as the Fig. 1...
Page 5
A092 L2 Service Manual 3. Back caver disassembly Unscrew 7 screws in back cover,as the Fig.2...
Page 6
A092 L2 Service Manual 4. Disassemble back cover with Tommy bar,as the Fig.3...
Page 7
A092 L2 Service Manual 5. Main board and front cover disassembly The main components of distribution,as the fig.4...
Page 8
A092 L2 Service Manual 6. Remove four screws and open the LCD con. & TP con. & Speaker & Vibrator, as the fig.5...
Page 9
A092 L2 Service Manual 7. Take out the main board,as the FIG.6...
Page 10
A092 L2 Service Manual 8. Remove the Back Camera and Front camera,as the FIG.7...
Page 11
A092 L2 Service Manual 9. Receiver and Light sensor rubber sleeve disassembly, as the fig.8...
Page 12
A092 L2 Service Manual 10. Exploded view...
Page 13
A092 L2 Service Manual L1 & L2 Repairing guide 1. LCD Check if the SW is correct, otherwise to upgrade the SW; Check the LCD if is ok, otherwise change a new LCD; If that the LCD loose, re-assemble the LCD and test;...
Page 14
A092 L2 Service Manual 2. Camera Checking the camera is assemble ok, re-assemble the camera and test; Using the good camera to do cross test, it can check if the camera is ok; Checking the camera connector if is ok as below picture, otherwise to re-solder or change a new one;...
Page 15
A092 L2 Service Manual 3. Touch Pannel Checking the SW and upgrade the SW; Checking the FPC of TP and re-assemble it; Using the good TP to do cross test; Checking the TP connector, otherwise re-solder or change a new one;...
Page 16
A092 L2 Service Manual 4. Ringer Checking the shrapnel of speaker if is ok; Checking the resistance of speaker if is ok, otherwise to change a new one; Checking the FPC if is ok; Checking SPK-FPC if connector with sub-board is ok.
Page 17
A092 L2 Service Manual 5. Receiver Checking the shrapnel of receiver if is ok; Checking the resistance of receiver if is ok, otherwise to change a new one; Checking the connector point on the main board if is ok, as below picture;...
Page 18
A092 L2 Service Manual 6. MIC and Vibrator Checking the MIC and Vibrator is cold soldering, re-solder it; Change the MIC and Vibrator; Checking the circuit of MIC and Vibrator; Checking the FPC if connect ok.
Page 19
A092 L2 Service Manual 7. Earphone Checking the shrapnel of earphone if is ok; Checking the connector point on the main board if is ok, as below picture; Change earphone connector; Checking the circuit of earphone.
Page 20
A092 L2 Service Manual 8. No Power On / Dead Checking the voltage of battery if is 3.8-4.2V and connect ok; Upgrade the SW; Checking the power on key and circuit around it.
Page 21
A092 L2 Service Manual 9. No Charging Checking the voltage of battery if is over 3.4V; Checking the charger and USB cable if is ok; Checking the USB connector and circuit if is ok.
Page 22
A092 L2 Service Manual 10. No SIM card and No memory card Checking the connector of T –card and SIM card; Change the connector of T –card and SIM card; Thanks For any query or suggestion please write to tech.help@micromaxinfo.com...